• Journal of information and communication convergence engineering
• /
• v.6 no.4
• /
• pp.417-420
• /
• 2008

Solar electric systems have very little impact on environment, making them one of the cleanest power-generating technologies available. While they are operating, PV systems produce no air pollution, hazardous waste, or noise, and they require no transportable fuels. In PV system design, the selection and proper installation of appropriately-sized components directly affect system reliability, lifetime, and initial cost. In this research, we have studied the PWM(Pulse Width Modulation) signals. I proposed an efficient photovoltaic power interface circuit incorporated with a DC-DC converter and a sine-pwm control method full-bridge inverter. In grid-connected solar power systems, the DC-DC converter operates at high switching frequency to make the output current a sine wave, whereas the full-bridge inverter operates at low switching frequency which is determined by the ac frequency. Thus, it can reduce the switching losses incurred by the full-bridge inverter. Full-bridge converter is controlled by using microprocessor control method, and its operation is verified through computer aided simulations.

• Proceedings of the KIEE Conference
• /
• 1997.07f
• /
• pp.1978-1981
• /
• 1997

This paper describes several PWM method for harmonics reduction in GTO inverter. The analysis and simulations of PWM techniques are carried out. The simulation results demonstrate that the programmed PWM methods(SHE PWM) are superior to the sine-modulated PWM method. The selected harmonic elimination (SHE) PWM scheme which eliminates specific lower order harmonics can generate high quality output waveform in PWM inverter.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.652-654
• /
• 2016

This paper shows the Design and implementation of sinusoidal BLDC motor drive logic using SVPWM method with FPGA. Sinusoidal BLDC motor driver logic consists of sine-wave PWM generator, dead-time and lead angle control logic. PWM generator logic is designed using SVPWM method for increase of 15.5% linear domain than general sine-wave PWM. This logic is verified and implemented using Spartan-6 FPGA Board. Test results show that THD(Total Harmonic Distortion) of motor-driving current is 19.2% and rotor position resolution is 1.6 degree.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.1 no.2
• /
• pp.70-73
• /
• 1987

This paper itltroduces a simple stair-case PWM using the pseudo-sinusoidal method. In a configuration of controller, the value of sine as a fundamental factor divided into stair-case level and the three-phase PWM inverter is composed by digital compound for each value of stair-case level. The three-phase output pulse at a fixed carrier frequency and a variable reference frequency is obtained under the effect of reduced harmonics. In this experiment, using the power FET as the switching device, 0.5 H.P. induction motor operation is performed when the switching frequency is 20KHz.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 1991.10a
• /
• pp.75-79
• /
• 1991

In this study, a new sinusoidal PWM inverter suitable for use with power MOSFETs is described. The output waveforms in the proposed OWM inverter are investigated both theoretically and experimentally. A modulating signal for the three-phase PWM inverter is obtained by adding 3nth harmonics to the conventional three-phase sine wave. By using the new modulating signal, the amplitude of the fundamental component is increased about 15 percent more than that of a conventional sine wave inverter and the commutation number of the inverter is decreased to two-thirds of a conventional one.

• The Proceedings of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.9 no.5
• /
• pp.51-56
• /
• 1995

The transistors of single phase 3 level PWM Inverter compose output power transistors and neutral point clamping transistors, which are NPN transistors. Waveforms of driving signals for this are PWM waves for power transistors and period operating waves for neutral point clamping transistors, which signals made W-type modulation from rectangular and sine wave. The output power transistors operate at ON-time complementary and neutral point clamping transistors operate at OFF-time complementary respectively. Therefore, each transistors operate in half period at parallel. Characteristics of this inverter circuit is parallel switching method about series switching method of general inverter. As modulation of 3 level drive signals made from full-wave rectifier of sine wave and rectangular wave, which are level wave about 3 level of complementary transistor inverter. So, this circuit composed complementary operation inverter of NPN transistors only compare with PNP-NPN complementary inverter, which have high power 3 level inverter of complementary operation.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.14 no.5
• /
• pp.66-73
• /
• 2000

A new modified command voltage of the third harmonics injected PWM inverter is proposed to control the inverter in overmodulation mode. The third harmonics injected PWM has a extended linear region compared with the sine PWM. But it still has a maximum voltage about 90% compared with the six step inverter. By analyzing the relationship between the modulation index and the peak of the fundamental component of the modified reference voltage, we can settle the problem in over modulation mode without iteration. Then we can increase the maximum fundamental component of the third harmonics injected PWM inverter comparative to six-step inverter continuously in over modulation mode. The simulation results of the inverter-induction motor system shows the validity of this method.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.515-517
• /
• 1989

This PWM inverter are used bridge circuit of two pair complementary transistor at each phase. The operation signals are 3 level PWM wave of W type and M type modulation, Which were obtained from switching time data by switching position calculation of triangular and sine wave. The output voltage waveforms of this inverter have the 5 level phase voltage and the 9 level line voltage of PWM.

• Proceedings of the KIEE Conference
• /
• 1988.07a
• /
• pp.148-150
• /
• 1988

The output characteristics of VSI by transistor depend upon bias signal with drive circuit. As the CTI is one of the VSI, takes case PWM output voltage. This Inverter operation is based upon position and negative of sinusoldal PWM signal by carrier triangular wave and compared sine one. Besides, the Inverter operation system required digital signal for microprocessor, sampling method of Inverter driver signals study for get rid of generated signal is error. In the paper, the method of 3 level PWM signal for CTI was studied. This method of signals depend upon caculated switching position of natural sampling with $10^{-6}$ modulation error for time flowchart programs.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.675-677
• /
• 2000

In the paper the eddy current loss in brushless DC motor due to switching frequency supplied by PWM inverter, is analyzed. The compensated conductivity is used in order to analyze the eddy current loss in brushless DC motor which has lamination structure. The eddy current loss is deceased when switching frequency supplied by PWM inverter is gradually increased from 1.2kHz up to 12kHz. The high switching frequency of PWM inverter make the output wave into a similar sine wave and this leads to the decreasing eddy current loss.