• Journal of the Korean Institute of Landscape Architecture
• /
• v.33 no.1 s.108
• /
• pp.49-57
• /
• 2005

The aim of this study was to explain the relationship between the landscape organization and evaluating factors to harmonize the buildings with natural landscape using the landscape simulation models (near view less than $100{\cal}m$) controled the distance and obtain some knowledges about the introduction of buildings into the recreation forest. Through this study, the results were summarized as follow ;1) As the distance got to be near, the evaluation of comprehensive scenery and natural quality became low. 2) At the view points according to the distance the clear landscape organization showed a high value of scenery in comparison with the simple landscape organization, 3) As the coniferous forest showed more high value in comparison with the deciduous forest, the forest type surrounding cottage is important factor evaluating the landscape in the recreation forest area.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.480-485
• /
• 2009

Offshore wind energy is gaining more attention. Ensuring proper design of offshore wind turbines and wind farms require knowledge of the external conditions in which the turbines and associated facilities are to operate. In this work, a three-bladed 5MW upwind wind turbine, which is supported by the monopile foundation, is studied by use of fully coupled aero-hydro-servo-elastic commercial simulation tool, 'GH-Bladed'$^{(R)}$. Specification of the structures are chosen from the OC3 (Offshore Code Comparison Collaboration) under "IEA Wind Annex XXIII-subtask2". The primary external conditions due to wind and waves are simulated. Design Load case 5.2 is investigated in this work. The steady state power curve and power production loads are evaluated. Comparison between different codes is made.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.931-935
• /
• 2004

This paper presents a comparison of the rotor position estimation of a switched reluctance motor(SRM) with built-in search coils. Squared euclidean distance, fuzzy logic and neural network are used to estimate the rotor position. The simulation is performed by three methods and the results are compared. The experiment of squared euclidean distance is achieved and compared with the simulation result.

• Journal of The Korean Astronomical Society
• /
• v.29 no.spc1
• /
• pp.123-124
• /
• 1996

Snapshots of eight SA and standard fields from low to high galactic latitudes were made using the KPNO 0.9m 2K $\times$ 2K CCD with a limiting magnitude from 19 to 22.5. The purpose of this study is to determine the vertical distribution of stars with respect to Galactic latitude and z-distance in comparison with the model simulation between intermediate population to the 'thick disk' component of scale height of a few kpc. Comparison of the preliminary results between observed and model simulation for 3 of the S fields shows good agreement both in V-mag and B- V color distributions. A bimodal distribution in B- V at high galactic latitude seems to be represented by a halo and 'thick disk' dwarf in the blue and by a normal disk dwarf population in the red.

• Industrial Engineering and Management Systems
• /
• v.14 no.3
• /
• pp.289-298
• /
• 2015

This paper analyses the best batch formations for order picking throughput in narrow-aisle order picking systems. Our analytical comparison finds that a high pick density variation leads to a heavy picker blocking. Simulation experiments show that a distance-based batching algorithm reduces picker blocking by decreasing the number of aisles visited and stabilizing the variation in number of picks per aisle by packing orders tightly, and that the solution quality and mechanism for determining the batch size dictated by the sorting strategy causes varying amounts of blocking. We conclude that combining a distance-based batching method with an appropriate batch sizing strategy will reduce picker blocking and shorten travel in narrow-aisle picking systems.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.10
• /
• pp.2787-2796
• /
• 1994

The modeling of combustion process is an important part in an engine simulation program. In this study, calculated results using a conventional B-K model and the other model which is called GESIM were compared with experimentally measured data of a three-cylinder spark-ignition engine under wide range of operating conditions. The burn rates calculated from the combustion models were compared with the burn rate calculated from the one-zone heat release analysis that uses measured pressure data as an input data. As a result of the two models' comparison, the GESIM combustion model conformed to be closer to the data acquired from the experiment in wide operating ranges. The GESIM model has been improved by introducing a variable that considers the flame size, the area of flame conacting the piston surface into the model, based on the comparison between the experimental result and the calculated results. The improved combustion model predicts experimental results more precisely than that of GESIM combustion model.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.260-264
• /
• 1998

Three phase Boost/Buck converter which have economical merits and simple control scheme, are analyzed and evaluated through comparative methods and digital simulation for equivalent load. Those play a part of voltage boost/buck as well as power factor correction with single switch. Controller operating in constant and variable frequency is used for rapid output response and stable system condition respectively. Moreover low THD property of single switched converters is available for inverter arc welding machine known as high power and low power factor. So, in this paper a comparison of the characteristics in boost and buck converter is described and then simulation results conforms the merits from point of view of power factor and voltage regulator.

• Communications for Statistical Applications and Methods
• /
• v.27 no.5
• /
• pp.501-510
• /
• 2020

Mardia (Biometrika, 57, 519-530, 1970) defined measures of multivariate skewness and kurtosis. Based on these measures, omnibus test statistics of multivariate normality are proposed using normalizing transformations. The transformations we consider are normal approximation and a Wilson-Hilferty transformation. The normalizing transformation proposed by Enomoto et al. (Communications in Statistics-Simulation and Computation, 49, 684-698, 2019) for the Mardia's kurtosis is also considered. A comparison of power is conducted by a simulation study. As a result, sum of squares of the normal approximation to the Mardia's skewness and the Enomoto's normalizing transformation to the Mardia's kurtosis seems to have relatively good power over the alternatives that are considered.

• Korean Journal of Geomatics
• /
• v.1 no.1
• /
• pp.15-20
• /
• 2001

In this study, several basic data for road design and GIS data were used for selecting the optimized road alignment database system. The cut and fill volumes were compared with existing manual road design method through the analysis and data application in this database system. We solved and estimated objective, economic, environmental and technical problems caused in road construction comparing existing manual method with the road alignment which was selected in GIS automatically. Also, we performed three dimensional simulation with the existing road design program and simulation of virtual reality through Virtual GIS. This study showed the method in selecting the optimized road alignment through the analysis and comparison of the selected road alignment. The goal of this study is comparison and analysis of definite cut and fill volume and environmental problem after the road construction through analyzing and comparing the social, economic, technical and environmental aspect in the road alignments with various statistic data.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2005.11a
• /
• pp.111-114
• /
• 2005

This paper presents a comparison of experimental value by hemispherical grounding simulation system and calculated value by CDEGS program for ground potential rise of structure. When a test current flowed through structure grounding electrodes, ground potential rise was measured and analyzed for types of structure using the hemispherical grounding simulation system in real time, and was computed by means of CDEGS program. The model structures were designed and fabricated with two types on a scale of one-one hundred sixty. When the experimental data were compared with the theoretical values, the similar profile was shown. Therefore, the confidence of measurement was obtained. The distributions of ground surface potential are dependent on the resistivity and absorption percentage in concrete attached to structure.