• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.16 no.3
• /
• pp.81-87
• /
• 2016

This paper analysis the AM-SCS-MMA (Adaptive Modulus-Soft Constraint Satisfaction-MMA) based on the adaptive modulus and minimus-disturbance technique in order to improve the stability and robustness in low signal to noise power of current MMA adaptive equalization algorithm. In AM-SCS-MMA, it updates the filter coefficient applying the adaptive modulus and minimum-disturbance technique of deterministic optimization problem instead of LMS or gradient descend algorithm for obtain the minimize the cost function of adaptive equalization. It is possible to improve the equalizer filter stability, robustness to the various noise characteristic and simultaneous reducing the intersymbol interference due to the amplitude and phase distortion occurred at channel. The computer simulation were performed for confirming the improved performance of SCS-MMA. For these, the output signal constellation of equalizer, residual isi, MSE, EMSE (Excess MSE) which means the channel traking capability and SER which means the robustness were applied. As a result of computer simulation, the AM-SCS-MMA have slow convergence time and less residual quantities after steady state, more good robustness in the poor signal to noise ratio, but poor in channel tracking capabilities was confirmed than MMA.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.11 no.5
• /
• pp.151-157
• /
• 2011

This study analyzed the posture balance of time variation for exercising body a period of time. Posture balance measured output values for the posture balance system of body moving in the multi-parameter. Posture moving variation had three methods such as open and closed eye, head moving and upper body moving. There were checked a parameter that measured vision, vestibular, somatosensory, CNS. This system was evaluated a data through the stability. This system has catched a signal for physical condition of body data such as a data acquisition system, data signal processing and feedback system. The output signal was generated Fourier analysis that using frequency of 0.1Hz, 0.1-0.5Hz, 0.5-1Hz and 1Hz over. The posture balance system will be used to support assessment for body moving the posture balance of time variation. It was expected to monitor a physical parameter for health verification system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.23 no.5
• /
• pp.1349-1359
• /
• 1998

In this paper, presented is the result of a digital implementation of a FM stereo composite signal generator. The chip utilizing DDFS(Direct Digital Frequency Synthesizer architecture is implemented using $1.0\mu\textrm{m}$ CMOS gate-array technology thereby replacing analog componentry. To verify the process of generating composite signals a conventional logic simulation method was used. The processed chip was mounted on an evaluation PCB to test and analyze to signals. According to the measurement result obtained by using a 12-bit DAC, the digital FM composite signal generator produces a 74DB spectrally pure signal over its entire tuning range, which is superior to that of analog counterpart by 14dB in it spectral reponse. And further enhancements of the spectral response is expected to be achieved by using a high resolution digital to analog converter, such as a 16-bit DAC. The resulting signals is superior to the signal of the analoy circuitry typically used, in major characteristics such as S/N ratios, accuracy, tuning stability, and signal seperation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.7
• /
• pp.1086-1093
• /
• 2001

A new linearization technique for RF high-power amplifiers(HPAs) using n-th order error signal generator (ESGn) is proposed. The n-th order ESG generates an error signal based on the complex envelope transfer characteristics of the HPA, which is combined at the output of the HPA. Therefore, the higher-order nonlinearlities are not affected by the ESG$\_$n/ and the stability of the linearized system is guaranteed due to the inherent open-loop configuration. Moreover, the output delay loss can be avoided, because the error signal is generated with the input signal of the HPA. The IMD(intermodulation distortion) improvement obtained applying the ESG$\_$7/ to 5 W class A HPA in cellular band demonstrates the feasibility of the proposed postdistortion system.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.62 no.8
• /
• pp.1132-1137
• /
• 2013

This paper considers the $H_{\infty}$ control problem for networked control systems(NCSs). In order to solve the problem which comes from discontinuous control signal in NCSs, an approach that discontinuous control signals treat time-varying delayed continuous signals is applied to achieve $H_{\infty}$ stability of NCSs. In addition, randomly occurring packet losses and disturbances are considered by introducing stochastic variables with Bernoulli distribution. Based on Lyapunov stability theory, a new stability condition is obtained via linear matrix inequality formulation to find the $H_{\infty}$ controller which achieves the mean square stability of NCSs. Finally, the proposed method is applied to a numerical example in order to show the effectiveness of our results.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.9
• /
• pp.64-72
• /
• 2012

The interest in wind power generation area such as developing and operating wind-diesel pilot complex in remote and island regions that have difficulty in having power plant and connecting to power system is growing rapidly in the world. We have installed and researched the hybrid system in Sekgok Pilot Complex to meet the new generation system. From the monitored data of the system, the performance of each diesel power plant is outstanding. However, step out problem was detected with respect to load sharing and synchronization with decentralized power supply. An advanced controller design having better response time and stability is needed to solve such problem. In this paper, we proposed the algorithm, through digital controller of Governor, which is applied to hybrid system. As a result, we obtained the stable frequency value in variable loading conditions. Also, we proved the advanced response time and stability through the simulation and experiment by applying additional current signal to the control algorithm.

• Journal of Advanced Marine Engineering and Technology
• /
• v.27 no.3
• /
• pp.412-420
• /
• 2003

This study describes the merits of PWM control of hydraulic system using high speed on-off valves. Generally, Electro-hydraulic valves can be classified into two classification: valves which are controlled by analog signal and which are controlled by digital. The former includes hydraulic servo valves and proportional valves which require A/D converters as interface to digital computer and too costly and sensitive to oil contamination because of complexity in structures. The latter includes high speed on-off valves which do not require A/D converters because they are normally operated in a pulse width modulation(PWM) method, and are low in price and robust to oil contamination because of their simple structures. The objectives of this study is to analyze the limit cycle which regularly appear in the position control system using 2/2way high speed on-off valves and to give a criterion for the stability of this system. The nonlinear characteristics of PWM and cylinder friction of this system are described by harmonic linearization and the effects of parameter variations to the system stability are simulated.

• Journal of Power Electronics
• /
• v.18 no.3
• /
• pp.853-862
• /
• 2018

Frequency coupling in the phase domain is a recently reported phenomenon for phase locked loop (PLL) based three-phase grid-inverter systems. This paper investigates the mechanism and stabilization method for the frequency coupling to the stability of grid-inverter systems. Self and accompanying admittance models are employed to represent the frequency coupling characteristics of the inverter, and a small signal equivalent circuit of a grid-inverter system is set up to reveal the mechanism of the frequency coupling to the system stability. The analysis reveals that the equivalent inverter admittance is changed due to the frequency coupling of the inverter, and the system stability is affected. In the end, retuning the bandwidth of the phase locked loop is presented to stabilize the three-phase grid-inverter system. Experimental results are given to verify the analysis and the stabilization scheme.

• Journal of Sensor Science and Technology
• /
• v.31 no.1
• /
• pp.57-63
• /
• 2022

This study describes a system that monitors the tool and cutting state of automatic beveling operation in real time. As a signal for cutting state monitoring, a motor current detected from the spindle drive system of the automatic beveling machine is used to monitor abnormal state. Because automatic beveling is processed using a face milling cutter, the cutting force mechanism is the same as the milling process. The predicted cutting torque is obtained using a cutting force model based on specific cutting resistance. Then, the predicted cutting torque is converted into the spindle motor current value, and cutting state stability is diagnosed by comparing it with the motor current value detected during beveling operation. The experimental results show that the spindle motor current can detect abnormal cutting state such as overload and tool wear during beveling operation, and can diagnose the cutting stability using the proposed equip-current line diagram.

• Science of Emotion and Sensibility
• /
• v.26 no.4
• /
• pp.41-50
• /
• 2023

This study aims to develop electromyography (EMG) textile electrodes and assess their performance and signal stability by examining variations in layer count and fabric types. We fabricated the electrodes through layering and pressing techniques, focusing on configurations with different layer counts (Layer-0, Layer-1, and Layer-2). Our findings indicate that layer presence significantly influences muscle activation measurements, with enhanced performance correlated with increased layer numbers. Subsequently, we created electrodes from five distinct fabrics (neoprene, spandex cushion, 100% polyester, nylon spandex, and cotton canvas), each maintaining a Layer-2 structure. In performance tests, nylon spandex fabric, particularly heavier variants, outperformed others, while the spandex cushion electrodes showed superior stability in muscle activation signal acquisition. This research elucidates the connection between electrode performance and factors like layer number and electrode-skin contact area. It suggests a novel approach to electrode design, focusing on layer properties and targeted pressure application on specific sensor areas, rather than uniformly increasing sleeve pressure.