• 전기학회논문지
• /
• 제57권7호
• /
• pp.1195-1199
• /
• 2008

In this paper, peak detector of generator's output voltage and variable gain controller are introduced for a fast dynamic response. The conventional r,m.s, signal detected has inherent time delay, and the dynamic response of generator using conventional PID controller has some problem in sudden load change. In this paper, the peak detector and signal selector with variable gain controller is used to overcome this problem. The main controller can check the voltage state from the peak detector. When a sudden load change, the over-voltage and under-voltage signal from peak detector change the controller's gain and exciter's current reference. The proposed scheme can improve the dynamic response, which is verified from experimental test of 200kW diesel engine-generator.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• 제3권2호
• /
• pp.251-257
• /
• 2003

In this paper, we wish to construct a optimal traffic cycle using wire remote control. if police vehicle or ambulance suddenly enter the traffic Intersection, it will increase the traffic accident. In this paper, wireless traffic light use the radio traffic control signal and research about the hardware manufacture to check special detectors on urgency vehicles may safety and rapidly enter traffic intersection. Also, this paper present a traffic signal control conditions that analyzes different traffic intersection flows in cases of saturated flows, where the real traffic volume demand is large and the capacity constraints of bottlenecks have significant effects on the flow patterns. Through computer simulation this wireless traffic light has been proven to be much more safety and efficient than fixed traffic signal light which does not consider emergency vehicles for safety escort.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.425-430
• /
• 2008

To verify the system performance of portable AE leak diagnosis system which can measure with moving conditions, AE activities such as RMS voltage level, AE signal trend, leak rate degree according to AE database, FFT spectrum were measured during operation on total 11 valves of the secondary system in nuclear power plant. AE activities were recorded and analyzed from various operating conditions including different temperature, type of valve, pressure difference, valve size and fluid. The results of this field study are utilized to select the type of sensors, the frequency band for filtering and thereby to improve the signal-to-noise ratio for diagnosis for diagnosis or monitoring of valves in operation. As the final result of application study above, portable type leak diagnosis system by AE was developed. The outcome of the study can be definitely applied as a means of the diagnosis or monitoring system for energy saving and prevention of accident for power plant valve. The purpose of this study is to verify availability of the acoustic emission in-situ monitoring method to the internal leak and operating conditions of the major valves at nuclear power plants. In this study, acoustic emission tests are performed when the pressurized temperature water and steam flowed through glove valve(main steam dump valve) and check valve(main steam outlet pump check valve) on the normal size of 12 and 18 ". The valve internal leak monitoring system for practical field was designed. The acoustic emission method was applied to the valves at the site, and the background noise was measured for the abnormal plant condition. To improve the reliability, a judgment of leak on the system was used various factors which are AE parameters, trend analysis, frequency analysis, voltage analysis and amplitude analysis of acoustic signal emitted from the valve operating condition internal leak.

• 대한조선학회논문집
• /
• 제51권2호
• /
• pp.122-129
• /
• 2014

Identification of the whipping response out of the combined wave-vibration response of a flexible sea going vessel is one of the most interesting research topic from ship designer's point of view. In order to achieve this goal, a novel methodology based on the wavelet cross-correlation technique was proposed in this paper. The cross-correlation of the wavelet power spectrum averaged across the frequency axis was introduced to check the similarity between the combined wave-vibration response and impulse response. The calculated cross-correlation of the wavelet power spectrum was normalized by the auto-correlation of the each spectrum with zero time lag, eventually providing the cross-correlation coefficient that stays between 0 and 1, precisely indicating the existence of the impulse response buried in the combined wave-vibration response. Additionally, the weight function was introduced while calculating the cross-correlation of the two spectrums in order to filter out the signal of lower frequency so that the accuracy of the similarity check becomes as high as possible. The validity of the proposed methodology was checked through the application to the artificially generated ideal combined wave-vibration signal, together with the more realistic signal obtained by running 3D hydroelasticity program WISH-Flex. The correspondence of the identified whipping instances between the results, one from the proposed method and the other from the calculated slamming modal force, was excellent.

• 한국소음진동공학회논문집
• /
• 제19권8호
• /
• pp.843-849
• /
• 2009

The reliable operation of a swing check valve in the main feed water system of a power plant is most essential for successful shout-down process. A failure to close the valve at proper time often leads to the instability of the main feed water system, or even to an emergency stop of the power plant. In reality it is a very difficult task to monitor the behavior of a swing check valve. Furthermore it is impossible to see the motion of the valve. In this work two measurements were carried out simultaneously to determine the precise valve closure time. The dynamic pressure measurements were made at the inlet and outlet regions of the swing check valve. The transient vibration of the valve housing in the direction of water flow was also measured, which enabled the measurement of the transient vibration of the valve housing near valve closure. By comparing the results produced from these measurements the precise valve closure time could be determined. By carrying out order tracking technique using the dynamic pressure signals and pump rpm signal, the complicated dynamic problems inside the main feed water system can be more easily dealt with. This measurement scheme might be implemented in a power plant on a real-time basis without much difficulty. If this could be implemented, valuable information essential for shut-down operations can readily be passed on to the main control room. The feasibility of this implementation was demonstrated by this experimental work.

• 방송공학회논문지
• /
• 제25권1호
• /
• pp.36-47
• /
• 2020

향상된 신뢰-전파 기반 알고리즘인 정규화 최소-합 알고리즘 혹은 오프셋 최소-합 알고리즘은 낮은 연산복잡도와 높은 복호 성능을 보여 LDPC(Low-Density Parity-Check) 부호의 복호에 널리 이용되고 있다. 그러나, 이 알고리즘들은 적절한 정규화 계수와 오프셋 계수가 이용되어야만 높은 복호 성능을 갖는다. 최근 제안된 CMD(Check Node Message Distribution) 차트와 최소자승법을 이용하여 정규화 계수를 찾는 방법은 기존의 계수 도출 방법보다 계산량이 적을 뿐 아니라 각 반복 복호마다 최적의 정규화 계수를 도출할 수 있기 때문에 복호 성능을 높일 수 있다. 본 논문에서는 이 방법을 응용하여 정규화와 오프셋이 조합된 최소-합 알고리즘의 보정 계수 조합의 도출을 위한 알고리즘을 제안하고자 한다. 차세대 방송 통신 표준인 ATSC 3.0용 LDPC 부호의 컴퓨터 모의실험은 제안한 알고리즘을 통해 도출된 보정 계수 조합을 사용하였을 때 타 복호 알고리즘보다 월등히 높은 복호 성능을 가지는 것을 보인다.

• 한국멀티미디어학회논문지
• /
• 제21권5호
• /
• pp.545-557
• /
• 2018

The Global Positioning System (GPS) has become popular and widely used in many fields from military to civilian applications. However, GPS signals are suffered from interference due to its weak signal over wireless channel. There are many types of interference, such as jamming, blocking multipath, and spoofing, which can mislead the operation of GPS receiver. In this paper, vector-based tracking loop model with integrity check is proposed to detect and mitigate the harmful effect of interference on GPS receiver operation. The suggested methods are implemented in the tracking loop of GPS receiver. As a first method, integrity check with carrier-to-noise ratio (C/No) monitoring technique is applied to detect the presence of interference and prevent contaminated channels out of tracking channels to calculate position. As a second method, a vector-based tracking loop using Extended Kalman Filter with adaptive noise covariance according to C/No monitoring results. The proposed methods have been implemented on simulated dataset. The results demonstrates that the suggested methods significantly mitigate interference of Additive White Gaussian Noise (AWGN) and improve position calculation by 44%.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.436-438
• /
• 2007

As the sensors and communication technology get advance, the remote health diagnosis for patients and senior persons at home are possible now without visiting doctors in hospitals. A low-power ubiquitous health check device was developed adapting Real-Time Embedded Linux is developed. This ubiquitous device is consisted of three sensors. The wrist type health checking terminal acquires periodically the health data by using a blood pressure sensor, a pulse sensor and a body temperature sensor. It transmits the health data to the access point located at the home center through the ZigBee wireless communication modem. This health data collector or access point device sends the data again to the main server operated in a hospital or health care organization. The health server control continuously the input data and sends an alarm signal to the assigned. doctor and responsible persons using cellular SMS when any dangerous events occur. This wrist type health check device has an embedded linux OS using Intel PAX255 MPU. The developed U-Health system is applicable for checking patients health in remote at home. And their family or related persons in remote site can check the patients health status at any time. They can be assured by receiving SMS record and alarm of emergency case which is transmitted from the health server.

• 방송공학회논문지
• /
• 제24권7호
• /
• pp.1221-1227
• /
• 2019

This paper describes a low-density parity-check (LDPC) coded index modulated orthogonal frequency division multiplexing with quasi-orthogonal sequence (IM-OFDM-QOS) and provides performance evaluations of the proposed system. By using QOS as the spreading code, IM-OFDM-QOS scheme can improve the reception performance than IM-OFDM-SS scheme for a given data rate. On the other hand, LDPC code is widely used to the latest wireless communication systems as forward error correction (FEC) scheme and has Shannon-limit approaching performance. Therefore, by applying LDPC code to IM-OFDM-QOS system as FEC scheme, the reception performance can be further improved. Simulation results show that significant signal-to-noise ratio (SNR) gains can be obtained for LDPC coded IM-OFDM-QOS system compared to the LDPC coded IM-OFDM-SS system and the SNR gain increases with the higher code rate.

• 한국정밀공학회지
• /
• 제12권11호
• /
• pp.110-117
• /
• 1995

This study presents and algorithm and related techniques which could satisfy the important properties of check weighers and conveyor scales. The algorithm of Recursive Least Squares Regression is applied for the weighing system simulated as a dynamic model of the second order. Using the model and the algorithm, model parameters and then the mass being weighed can be determined from the step input. The performance of the algorithm was tested on a check weigher. Discussions were extended to the development of noise reduction techniques and to the lagged introduction of objects on the moving plate. It turns out that the algorithm shows several desirable features suitable for real-time signal processing with a microcomputer, which are high precision and stability in noisy environment.