• 전자공학회논문지D
• /
• 제34D권5호
• /
• pp.45-51
• /
• 1997

Low temperature activation of dopants which were doped using ion mass doping system in amorphous silicon(a-Si) thin films was investigated. With a 20.angs.-thick Ni film on top of the a-Si thin film, the activation temperature of dopants lowered to 500.deg. C. When the doping was performaed after the deposition of Ni thin film on the a-Si thin films (post-doping), the activation time was shorter than that of dopants mass, the activation time of the dopants doped by pre-doping method increased. It turned NiSi2 formation, while the decrease of activation time was mainly due to the enhancement of the NiSi2 formation by mixing of Ni and a-Si at the interface of Ni and a -Si thin during the ion doping process.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제8권2호
• /
• pp.111-114
• /
• 2008

We studied the influence of nanocrystalline silicon (nc-Si) thin film thickness on top gate nc-Si thin film transistor (TFT) fabricated at $180^{\circ}C$. The nc-Si thickness affects the characteristics of nc-Si TFT due to the nc-Si growth similar to a columnar. As the thickness of nc-Si increases from 40 nm to 200 nm, the grain size was increased from 20 nm to 40 nm. Having a large grain size, the thick nc-Si TFT surpasses the thin nc-Si TFT in terms of electrical characteristics such as field effect mobility. The channel resistance was decreased due to growth of the grain. We obtained the experimental results that the field effect mobility of the fabricated devices of which nc-Si thickness is 60, 90 and 130 nm are 26, 77 and $119\;cm^2/Vsec$, respectively. The leakage current, however, is increased from $7.2{\times}10^{-10}$ to $1.9{\times}10^{-8}\;A$ at $V_{GS}=-4.4\;V$ when the nc-Si thickness increases. It is originated from the decrease of the channel resistance.

• Transactions on Electrical and Electronic Materials
• /
• 제6권1호
• /
• pp.22-24
• /
• 2005

We studied the nematic liquid crystal (NLC) aligning capabilities using the new alignment material of the SiC (Silicon Carbide) thin film. The SiC thin film exhibits good chemical and thermal stability. The good thermal and chemical stability makes SiC an attractive candidate for electronic applications. A vertical alignment of nematic liquid crystal by ion beam exposure on the SiC thin film surface was achieved. The about $87{\circ}$ of stable pretilt angle was achieved at the range from $30{\circ}$ to $45{\circ}$ of incident angle. The good LC alignment is maintained by the ion beam alignment method on the SiC thin film surface at high annealing temperatures up to $300{\circ}C$.

• 전자공학회논문지A
• /
• 제29A권9호
• /
• pp.29-35
• /
• 1992

Dielectric thin film of N/O (Si$_{3}N_[4}/SIO_{2}$) for high density stacked dynamic-RAM cell was formed by LPCVD and oxidation(Dry & pyrogenic oxidation methods) of the top Si$_{3}N_[4}$ film. The thickness, structure and composition of this film were measured by ellipsometer, high frequency C-V meter, high resolution TEM, AES, and SIMS. The thickness limit of Si$_{3}N_[4}$ film in making thin N/O structure layer was 7nm. In this experiment, the film with thinner than 7nm was not thick enough as oxygen diffusion barrier, and oxygen punched through the film and interfacial oxidation occurred at the phase boundary between Si$_{3}N_[4}$ and polycrystalline silicon electrode.

• 한국전기전자재료학회논문지
• /
• 제19권8호
• /
• pp.758-763
• /
• 2006

We has been studied the thin film encapsulation effect for organic light-emitting diodes (OLED). To evaluate the passivation properties of the passivation layer materials, we have carried out the fabrication of green light emitting diodes with ultra violet(UV) light absorbing polymer resin, $SiO_2,\;and\;SiN_x$, respectively. From the measurement results of shrinkage properties according to the exposure time to the atmosphere, we found that $SiN_x$ thin film is the best material for passivation layer. We have investigated the emission efficiency and life time of OLED device using the package structure of $OLED/SiN_x/polymer$ resin/Al/polymer resin. The emission efficiency of this OLED device was 13 lm/W and life time was about 2,000 hours, which reach 95 % of the performance for the OLED encapsulated with metal.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집
• /
• pp.36-39
• /
• 2002

Polycrystalline silicon (poly-Si) thin film transistor (TFT) technology is emerging as a key technology for active matrix liquid crystal displays (AMLCD), allowing the integration of both active matrix and driving circuit on the same substrate (normally glass). As high temperature process is not used for glass substrate because of the low softening points below 450$^{\circ}C$. However, high temperature process is required for getting high crystallization volume fraction (i.e. crystallinity). A poly-Si thin film transistor has been fabricated to investigate the effect of high temperature process on the molybdenum (Mo) substrate. Improve of the crystallinity over 75% has been noticed. The properties of structural and electrical at high temperature poly-Si thin film transistor on Mo substrate have been also analyzed using a sputtering method

• 한국재료학회지
• /
• 제24권3호
• /
• pp.135-139
• /
• 2014

To obtain the transistor with ambipolar transfer characteristics, IGZO/SiOC thin film transistor was prepared on SiOC with various polarities as a gate insulator. The interface between a channel and insulator showed the Ohmic and Schottky contacts in the bias field of -5V ~ +5V. These contact characteristics depended on the polarities of SiOC gate insulators. The transfer characteristics of TFTs were observed the Ohmic contact on SiOC with polarity, but Schottky contact on SiOC with low polarity. The IGZO/SiOC thin film transistor with a Schottky contact in a short range bias electric field exhibited ambipolar transfer characteristics, but that with Ohmic contact in a short range electric field showed unipolar characteristics by the trapping phenomenon due to the trapped ionized defect formation.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2009년도 9th International Meeting on Information Display
• /
• pp.1604-1607
• /
• 2009

YAG laser crystallization of Si-based thin film deposited on plastic substrate has been studied. The Si-based thin films as crystallization precursor are with varied hydrogen (H) content. The effect of the H content on the crystallinity of the resulted poly-Si film has been investigated. The experimental results of the poly-Si crystallized by doublefrequency YAG laser shows that the initial dehydrogenation process could be left out if ${\mu}c$-Si was adopted as the crystallization precursor. The YAG laser annealing condition on plastic substrate and the crystallization results have been discussed in the paper.

• 한국재료학회지
• /
• 제23권6호
• /
• pp.334-338
• /
• 2013

In this study, $BaTiO_3$ thin films were grown by RF-magnetron sputtering, and the effects of the thin film thickness on the structural characteristics of $BaTiO_3$ thin films were systematically investigated. Instead of the oxide substrates generally used for the growth of $BaTiO_3$ thin films, p-Si substrates which are widely used in the current semiconductor processing, were used in this study in order to pursue high efficiency in device integration processing. For the crystallization of the grown thin films, annealing was carried out in air, and the annealing temperature was varied from $700^{\circ}C$. The changed thickness was within 200 nm~1200 nm. The XRD results showed that the best crystal quality was obtained for ample thicknesses 700 nm~1200 nm. The SEM analysis revealed that Si/$BaTiO_3$ are good quality interface characteristics within 300 nm when observed thickness. And surface roughness observed of $BaTiO_3$ thin films from AFM measurement are good quality surface characteristics within 300 nm. Depth-profiling analysis through GDS (glow discharge spectrometer) showed that the stoichiometric composition could be maintained. The results obtained in this study clearly revealed $BaTiO_3$ thin films grown on a p-Si substrate such as thin film thickness. The optimum thickness was 300 nm, the thin film was found to have the characteristics of thin film with good electrical properties.

• 한국표면공학회지
• /
• 제52권4호
• /
• pp.211-226
• /
• 2019

Optical thin films were deposited by using a reactive pulsed DC magnetron sputtering method with a high density plasma(HDP). In this study, the effect of sputtering process conditions on the microstructure and optical properties of $SiO_2$, $TiO_2$, $Nb_2O_5$ thin films was clarified. These thin films had flat and dense microstructure, stable stoichiometric composition at the optimal conditions of low working pressure, high pulsed DC power and RF power(HDP). Also, the refractive index of the $SiO_2$ thin films was almost constant, but the refractive indices of $TiO_2$ and $Nb_2O_5$ thin films were changed depending on the microstructure of these films. Antireflection films of $Air/SiO_2/Nb_2O_5/SiO_2/Nb_2O_5/SiO_2/Nb_2O_5/Glass$ structure designed by Macleod program were manufactured by our developed sputtering system. Transmittance and reflectance of the manufactured multilayer films showed outstanding value with the level of 95% and 0.3%, respectively, and also had excellent durability.