• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38B no.5
• /
• pp.337-343
• /
• 2013

In this paper, IEEE 802.11 based WLAN(5.2/5.8GHz) wideband Weathercock-shaped microstrip patch antenna was designed and manufactured. The antenna has a size of $17.4{\times}17.4mm^2$ and utilized FR-4 board. The size was minimized for mobility, and Weathercock-shaped U-slot and short-pin was inserted to satisfy adequate bandwidth and double bandwidth resonance characteristics. In addition, the antenna incorporated single both-sided patch, and simulation design optimized the Weathercock-shaped, position of the U-slot and the short-pin, and the length of the patch for the measurement. The manufactured antenna achieved a bandwidth of 695MHz from 5.2~5.8GHz zone(Return loss<-10dB). Achieved a beam width of $81.13^{\circ}$ and $85.43^{\circ}$ for 3-dB beam width of H plane and E p;ane radiation pattern, there was 3.17~4.85dBi gain.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.18 no.8
• /
• pp.854-861
• /
• 2007

In this paper, a compact L-shaped shorted pin patch to be used at local oscillator port in radar detector is proposed. Shorted pin patch operates as short-open cavity while conventional patch operates as open-open cavity. Shorted pins are L-shaped to obtain quarter wave length and three-quarter wave length resonance for the fundamental(X-band) and $2^{nd}(3^{rd})$(K- and Ka-band) mode resonance frequency, respectively. Thus, the proposed patch can be compact. It is also possible to operate at triple band(X-, K-, Ka-band) with small return loss in radar detector, It is expected that shorted pin patch could improve radar detector sensitivity.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.23 no.2
• /
• pp.236-242
• /
• 1986

The dependence of the current-voltage characteristics of hydrogenated amorphous silicon pin solar cells on the illumimination light intensity has been investigated. The open circuit voltage increases linearly with increasing the logarithm of light intensity up to AM 1, and nearly saturates above AM 1, indicating the open circuit voltage approaching the built-in potential of the pin solar cell above AM 1. The short circuit current density increase with light intensity in proportion to I**0.85 before and I**0.97 after light exposure. Since the series resistance devreses and shunt resistance increases with light intensily, the fill factor increases with light illumination. To increase the fill factor at high illumination in large area solar cells, t6he grid pattern on the ITO substrates should be made. Long light exposure on the solar cells gives rise to the increase of bulk resistance and defect states, resulting in the decrease of the fil factor and short circuit current density. The potential drop in the bulk of the a-Si:H pin solar cells at short circuit condition increases with decreasing temperature, and increases after long light exposure.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.891-894
• /
• 1999

According to increasing the integration of the device, there are important consideration about the improvement of the reliability in the product. To improve the reliability of the device, the test parameters and test time are increased. There are no pin-to-pin short test and pin-to-pin leakage test in the present test items to analysis the characteristics and reliability of the device. The purpose of the paper is to model the pin-to-pin phenomenon and propose to modify the test method present and to test the new pin-to-pin DC parameters. These modified and additive test items are applied to product test and confirmed to improve the reliability of product test.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.9 no.3
• /
• pp.259-267
• /
• 1997

Average heat transfer coefficients and friction coefficients have been measured from staggered short pin-fin arrays to investigate the effect of fin shapes. Flow entering into the test section is a fully developed duct flow and the Reynolds number ranges from 5,000 to 25,000 based on fin diameter and average approaching velocity. The fin has three different shapes; uniform-diameter circular fin, two stepped-diameter circular fins. Average heat transfer rates change slightly with the fin shapes. However, friction loss(pressure loss) for the stepped-diameter fins is significantly less than that for the uniform-diameter fin. This results indicate that the stepped-diameter fin arrays in duct flow enhance heat transfer rates largely based on unit pumping power.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.4A
• /
• pp.324-329
• /
• 2009

In this paper, a novel Snowflake-shaped microstrip patch antenna for application in the WLAN(5.2/5.8GHz) band is designed and fabricated. The size of antenna is $21.2{\times}16mm^2$ and substrate is used Taconic-RF30. To obtain sufficient bandwidth in Return loss <-10dB and dual resonance characteristic, the Short-pin is inserted on the patch and the coaxial probe source is used. The measured results of fabricated antenna show 220MHz and 135MHz bandwidth in Return loss <-10dB referenced to the WLAN(5.2/5.8GHz) band. The measured antenna gain is $4.7{\sim}6.9dBi$ in the WLAN(5.2/5.8GHz) band. The experimental 3-dB beam width in I-plane and H-plane are $73.2^{\circ}/82.75^{\circ}$ for 5.1500Hz, $74.56^{\circ}/83.63^{\circ}$ for 5.3500Hz, and $86.24^{\circ}/85.15^{\circ}$ for 5.7850Hz, respectively.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.9A
• /
• pp.900-905
• /
• 2006

In this paper, PIFA antenna for $2.40{\sim}2.482GHz\;and\;5.75{\sim}5.85GHz$ is designed, fabricated, and measured. The prototype consist of hair-pin and short-pin. To obtain suitable bandwidth, the form layer is inserted between ground plane and substrate. Important parameters in the design are hair-pin length, width, position, air-gap height, and feed point position. From these parameters optimized, a PIFA antenna is fabricated and measured. The measured results of the antenna are obtained as follows results. The resonant frequency of the fabrication PIFA antenna is 2.37GHz and 5.86GHz bandwidth for approximately 90MHz with 350MHz(VSWR<2.0) and the gain is $1.91{\sim}4.37dBi$. H-plan and E-plan at 2.4GHz and 5.8GHz are shown as $52.83^{\circ},\;85.90^{\circ}\;and\;68.68^{\circ},\;52.143^{\circ}$ respectively.

• Tribology and Lubricants
• /
• v.23 no.6
• /
• pp.306-311
• /
• 2007

This paper presents the friction characteristics of pb-fres pin bushing bearings for an automotive gasoline engine. The external load is 100 N to 600 N and the speed of the pin bushing bearing is 1000 rpm to 3000 rpm against the rubbing surfaces. And the contact modes of rubbing surfaces between a piston pin and a pb-free pin bushing specimen are a dry friction, an oil lubricated friction and a mixed friction that is starved by a lack of engine oil. Two influential factors of a contact rubbing modes and a material property are very important parameters on the tribological performance of a friction characteristic between a piston pin and a pb-free pin bushing. The experimental result shows that the pin bushing speed of 2000 rpm shows a typical oil film lubricated sliding contact mode in which means that as the applied load is increased, the friction loss is increasing. But other contact mode depending on the speed and the load may affect to the fiction coefficient without a regular and uniform trend. In summary, the oil lubricated rubbing surface definitely decreases a running-in period in short and increase oil film stiffness, and this may leads the reduction of a friction loss.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2013.05a
• /
• pp.1259-1260
• /
• 2013

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.07a
• /
• pp.98-99
• /
• 2003

PIN photodiode has been used in solid-state detector for x-ray detection as a photosensor of visible light from scintillator. Since the light from CWO is short wavelength having peak at 490nm, the light is absorbed within a very shallow layer near the surface of the photodiode before arriving at the depletion layer and does not contribute to the signal. In designing the PIN photodiode, it is important to make the p-layer as shallow as possible. (omitted)