• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.8 no.1
• /
• pp.23-26
• /
• 2002

This study was carried out to investigate vibration shock and dropping shock of refrigerator during physical distribution. The values of vibration shock were measured to be ${\sim}3G$ for up and down direction, ${\sim}0.8G$ for right and left direction and ${\sim}0.5G$ for back and forth direction on the national road. There was no damage during transport. From the results of dropping test by KS A 1026(General Rules of Performance Testing for Packaged Freights), relative equations were gained as follow : y = 0.12x + 7.63(where y is G-factor and x is Dropping height). The maximum values of dropping shock during materials handling were measured to be 11G. This shock value was corresponding to dropping shocks of dropping height 28.3cm by KS A 1026.

• YAKHAK HOEJI
• /
• v.48 no.1
• /
• pp.82-87
• /
• 2004

Mungbean trypsin inhibitor (MBTI) was isolated and purified from Mung bean which has been used as a galenic and traditional food. MBTI and poly(ethylene glycol) were conjugated by using water soluble carbodiimide. We evaluated the therapeutic value of the MBTI and MBTI-PEG conjugate using animal models, sublethal septic shock model in guinea pig caused by pseudomonal elastase, shock model in rat caused by lipopolysaccharide, and the vascular permeability test by using pseudomonal elastase. In two shock model in guinea p Is and in rat, hypotesion shock was inhibited by pretreatment of MBTI. And also the vascular permeability caused by pseudomonal elastase reduced by pretreatment of MBTI. Also, therapeutic value of the MBTI-PEG conjugate was evaluated by using the sublethal septic shock model caused by pseudomonal elastase. The MBTI-PEG conjugate was more effective than native MBTI against pseudomonal elastase induced septic shock in guinea pig model.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.581-586
• /
• 2000

Explosively activated pyro-technic device is used to release exhausted rocket booster or payloads at prescribed times in the rocket's flight. It creates pyro-shock environment that rocket or payload components must survive. With the shock spectra acquired from flight data, laboratory test should be performed before flight to check whether all of component can sustain the shock environment. The pyro-shock environment simulation was created by the resonance fixture response to a projectile impact. Desired shock spectra is realized by adjusting the natural frequency of resonance plate and the velocity of impact hammer. This paper describes the development process of Pyro-shock testing machine, which is designed and tested by Korean engineers, to verify components of Korean Sounding Rocket(KSR-3) and the other Korean space vehicle. Both analytical and experimental techniques are introduced in this paper.

• Journal of Energy Engineering
• /
• v.21 no.1
• /
• pp.26-32
• /
• 2012

This study has been performed Thermal Shock test for analyze the cause of Power drop in PV(Photovoltaic) Module. Thermal Shock test condition was performed with temperature range from $-40^{\circ}C{\sim}85^{\circ}C$. One cycle time is 30min. which are consist of low and high temperature 15min. each other. The test was performed with total 500cycles. EL, I-V were conducted every 100cycle up to 500cycles. Mono Cell resulted in 8% Power drop rates in Bare Cell and 9% in Solar Cell. In the case of Multi Cell resulted in 6% Power drop rates in Bare Cell and 13% in Solar Cell. After Thermal Shock test, Solar Cell's Power drop resulted from surface damages, but in the case of Bare Cell's Power drop had no surface damages. Therefore, Bare Cell's Power drop was confirmed as according to leakage current increase by analysis of Fill Factor after Thermal Shock test. Also, Solar Cell's Power drop rates are higher than that of Bare Cell because of surface damages and consuming electric power increase. From now on, it should be considered that analyzed the reasons of Fill Factor decrease and irregular Power drop in PV module and Cell level using cross section, various conditions and test methods.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.11 no.4
• /
• pp.51-62
• /
• 2012

According to the Lighthill and Whitham's shock wave model, a shock wave exists even in a homogeneous speed condition. They referred this wave as unobservable- analogous to a radio wave that cannot be seen. Recent research has attempted to identify how such a counterintuitive conclusion results from the Lighthill and Whitham's shock wave model, and derive a new asymptotical shock wave model. The asymptotical model showed that the shock wave in a homogenous speed traffic stream is identical to the ambient vehicle speed. Thus, no radio wave-like shock wave exists. However, performance tests of the asymptotical model using numerical values have not yet been performed. We investigated the new asymptotical model by examining the implications of the new model, and tested it using numerical values based on a test scenario. Our investigation showed that the only difference between both models is in the third term of the equations, and that this difference has a crucial role in the model output. Incorporation of model parameter${\alpha}$ is another distinctive feature of the asymptotical model. This parameter makes the asymptotical model more flexible. In addition, due to various choices of ${\alpha}$ values, model calibration to accommodate various traffic flow situations is achievable. In Lighthill and Whitham's model, this is not possible. Our numerical test results showed that the new model yields significantly different outputs: the predicted shock wave speeds of the asymptotical model tend to lean toward the downstream direction in most cases compared to the shock wave speeds of Lighthill and Whitham's model for the same test environment. Statistical tests of significance also indicate that the outputs of the new model are significantly different than the corresponding outputs of Lighthill and Whitham's model.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.250-253
• /
• 2005

This paper is investigates the separation shock of payload fairing. Separation test of subscale PLF using half separation device and half PLA is performed. Resulting shock loads at equipment bay and fairing joint are measured. Pyroshock estimation is performed using AUTOSEA Pyroshock Module. Input data to analysis model is obtained from the separation test results of subscale PLF. And model of AUTOSEA is updated comparing results between tests and analysis.. This enables us to validate the AUTOSEA model. Tuned model of subscale PLF and separation device is used to update full scale model, and the shock analysis result of full scale model is estimated in this paper. This paper also discusses the results regarding the difficulty of structural modeling and its numerical implementation in AutoSEA2 Software.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.05a
• /
• pp.809-812
• /
• 2005

This paper explains environmental tests of vessel-launched missiles, verifying if a fully assembled missile performs properly from disturbance on delivery by vehicles or naval vessels. We also have operated vibration tests by ground and naval transportation as well as shock tests by naval transportation before firing. The environmental tests have adopted Military Standard Specification and confirmed missile's reliability by performance tests, followed by missile's development. However, this significant testing which have meaning was dong by the missile's body and not with parts.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.121-124
• /
• 1995

This study is aimed at cutting down the cost, weight and improving process by replacing the traditional sintered piston of the shock absorber with engineering plastic piston by means of injection molding. To obtain the high mechanical properties, glass fiber material was selected adequately and forming analysis considering fiber orientation was made to remove the forming deficit fators and to construct the optimal runner system. In addition, structural analysis using commercial software MOLDFLOW was performed under near conditions in actual driving of automotive. The results from the internal pressure process test, oilproof test based on forming, structural and strength analysis shows that hydraulic close performance and damping force considering the out of roundness of shock absorber are relatively good.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.11a
• /
• pp.412-417
• /
• 2003

As optical disk drives become designed for portable and hostile environment, higher storage density and smaller size, optical disk drives have a possibility to miss the track and not to read the data. This paper presents the modeling of an optical disk drive as 3-DOF system. Optical disk drives are tested with a linear drop test device and their results are compared with simulation results in order to verify the shock analysis. Finally, this paper shows shock response of a optical disk drive with changes of parameters

• Transactions of the Society of Information Storage Systems
• /
• v.9 no.2
• /
• pp.51-55
• /
• 2013

HDD has been easily exposed to the external shock and vibration because HDD has to apply to mobile devices. Therefore, the stiffness of base has been the important factors for the design of HDD. To improve the stiffness of base, the frame was applied to the base. First, the finite element model of the base was constructed. Then, the FE model was verified by modal analysis. Drop test was performed to confirming the shock simulation model. The dynamic characteristic of original base which is verified is compared with the base which is applied the frame through modal analysis and shock analysis.