• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.17-20
• /
• 2008

본 연구는 플랫 플레이트의 전단보강체에 관한 연구의 일부이고, 슬래브-기둥 접합부의 수직전단력 실험에서 보강체의 종류에 따라 뚫림전단강도에 대한 영향을 확인하는 것을 목표로 한다. 제안된 4개의 보강체는 s/s bar, c/s bar, wiremesh, CFS이다. 전체 5개의 실험체를 제작하고 실험을 행하였으며, 슬래브의 제원은 $2.63{\ast}2.725.0.18m$이며, 중앙에 0.6${\ast}$0.8m의 단면을 가진 기둥을 가지고 있다. 실험결과를 요약하면 CFS 전단보강체는 콘크리트와의 부착이 충분히 되지 않아서 보강체가 보강력을 발휘하기 전에 보강체와 콘크리트가 분리되어 보강효과를 발휘하지 못하였다. CFS를 제외한 3개의 전단보강체는 슬래브-기둥 접합부의 뚫림전단 저항력을 증가시켜 높은 보강효과를 나타내었다. 전단보강이 되지 않은 실험체에 비하여 강도면에서는 16${\sim}$35%의 증가율을 보였고, 변형능력면에서는 35${\sim}$63%의 증가율을 보였다.

• 대한소아치과학회지
• /
• 제29권4호
• /
• pp.509-518
• /
• 2002

치과 임상에서 널리 사용되고 있는 대표적인 심미성 접착 수복재료인 복합 레진과 글라스 아이어노머 시멘트의 단점을 보완하여 개발된 것으로 알려진 컴포머의 유치 상아질에 대한 결합력을 평가하고자 본 실험을 수행하였다. 치아 교환을 이유로 최근에 발거된 유구치 144개를 실험대상 치아로 선정하였으며, 이 중 120개의 치아는 전단강도 측정실험을 위하여 나머지 24개는 결합계면의 주사전자 현미경 관찰을 위해 무작위로 배분하였다. 각 치아마다 $3{\times}4mm$의 상아질을 노출시킨 후 내경 2.6mm, 높이 2.0mm의 크기로 제작된 폴리에틸렌 주형을 상아질 표면에 고정시킨 다음 각각의 재료를 설정 조건에 따라 충전하였다. 전단강도 실험표본은 만능 시험기를 사용하여 측정하였으며, 주사 전자현미경 관찰 표본 중 1/2은 다시 근원심으로 절단하여 그 결합계면을 관찰하였으며 나머지 1/2은 치아를 완전 탈회시킨 후 상아질 내에 침투된 접착제의 형태를 관찰하였다. 본 실험의 결과 모든 컴포머 군($II{\sim}V$)의 전단강도가 글라스 아이어노머 군(I)보다 높게 나타났고, 산 부식을 시행한 컴포머 군(III, V)이 산 부식을 시행하지 않고 충전한 컴포머 군(II, IV)에 비해 높은 전단강도를 보였으며(p<.05) 복합 레진 군(VI)과의 비교에서도 통계학적인 유의차가 없었다(p>.05). 서로 다른 접착제를 사용한 컴포머군 간의 비교에서는 모두 유의차가 나타나지 않았다. 상아질-수복재 계면의 관찰 결과, 산 부식 처리된 상아질과 결합된 컴포머 군이 처리하지 않은 군에 비해 다소 두꺼운 혼화층이 균일하게 형성되어 있었고 레진 돌기도 더욱 치밀하게 침투한 양상을 보였다. 주사 현미경 관찰에서는 산부식 하지 않은 컴포머 군이 전반적으로 짧고 얇은 레진 태그가 불규칙하게 분포되어 있는 양상을 보인 반면, 산부식을 시행한 군과 복합 레진 군에서는 굵고 긴 레진 태그들이 규칙적이며 치밀한 분포를 나타냈다. 이상의 결과로 미루어 상아질의 산 부식 과정이 컴포머의 결합력 증진에 긍정적 요인으로 작용한 반면 상아질 접착제의 종류는 별다른 영향을 주지 않은 것으로 분석되었다. 결합강도의 비교에서 컴포머가 글라스 아이어노머에 비해 우수한 것으로 평가되어 소아 환자의 유구치 심미 수복재료로서의 가능성이 입증되었다.

• 한국구조물진단유지관리공학회 논문집
• /
• 제26권6호
• /
• pp.73-81
• /
• 2022

최근 구조물의 사용연한이 증가함에 따라 다양한 요인에 의해 철근이 부식되어 구조물의 내하력이 감소하는 문제들이 발생하고 있다. 이를 해결하기 위하여 내식성, 경량성, 고인장강도를 갖는 FRP 보강근의 부착특성에 대한 연구가 활발히 진행중이나, 콘크리트에 매립된 격자형 CFRP 보강재의 부착특성에 관한 연구는 미흡한 실정이다. 따라서 격자형 CFRP 보강재를 철근의 대체재로 사용하고 사용성 측면에서 부착특성을 평가하기 위해, 격자형 CFRP 보강재의 종방향 부착길이와 횡방향 격자길이를 변수로 하여 직접인발시험을 수행하였다. 이를 통해 격자형 CFRP 보강재의 부착하중-슬립 곡선을 도출하였으며, 부착거동을 분석하였다. 총 부착하중 식은 종방향 부착길이의 부착력과 횡방향 격자의 전단력의 합으로 제안하였으며, 부착하중-슬립곡선의 면적을 전체 일로 표현하여 슬립량에 대한 에너지 소산량의 변화를 분석하여 횡방향 격자가 부착력에 미치는 영향에 대하여 검토하였다.

• Structural Engineering and Mechanics
• /
• 제75권6호
• /
• pp.643-657
• /
• 2020

This study presents experimental and numerical investigations on circular steel tube confined ultra high performance concrete (UHPC) columns under axial compression. The plain UHPC without fibers was designed to achieve a compressive strength ranged between 150 MPa and 200 MPa. Test results revealed that loading on only the UHPC core can generate a significant confinement effect for the UHPC core, thus leading to an increase in both strength and ductility of columns, and restricting the inherent brittleness of unconfined UHPC. All tested columns failed by shear plane failure of the UHPC core, this causes a softening stage in the axial load versus axial strain curves. In addition, an increase in the steel tube thickness or the confinement index was found to increase the strength and ductility enhancement and to reduce the magnitude of the loss of load capacity. Besides, steel tube with higher yield strength can improve the post-peak behavior. Based on the test results, the load contribution of the steel tube and the concrete core to the total load was examined. It was found that no significant confinement effect can be developed before the peak load, while the ductility of post-peak stage is mainly affected by the degree of the confinement effect. A finite element model (FEM) was also constructed in ABAQUS software to validate the test results. The effect of bond strength between the steel tube and the UHPC core was also investigated through the change of friction coefficient in FEM. Furthermore, the mechanism of circular steel tube confined UHPC columns was examined using the established FEM. Based on the results of FEM, the confining pressures along the height of each modeled column were shown. Furthermore, the interaction between the steel tube and the UHPC core was displayed through the slip length and shear stresses between two surfaces of two materials.

• 한국구조물진단유지관리공학회 논문집
• /
• 제12권2호
• /
• pp.103-112
• /
• 2008

FRP와 콘크리트의 접착강도를 평가하기 위해 현장에서 일반적으로 사용되는 Pull-off 실험방법은 FRP 복합체의 손상을 초래하며 더욱이 FRP의 최대 pull-off 강도가 콘크리트의 인장강도에 의해 제한되는 단점을 지니고 있다. 이에 따라 구조보강용 접착제의 역학적 특성을 1차적으로 평가할 수 있는 간접적인 실험방법의 개발이 요구된다. 본 연구에서는 여러나라에서 각기 제안되고 있는 실험규격에 대한 비교실험을 통하여 구조보강용 접착제의 역학적 특성을 개략적으로 예측할 수 있는 표준화된 실험방법 및 평가기준을 제안하고자 하였다. 본 연구결과를 바탕으로 인장전단접착강도 시험의 접착제 두께, 압축/휨강도 시험체의 제원 등이 통일되어 표준시험체 제원을 도출할 수 있었다.

• 대한치과보철학회지
• /
• 제30권1호
• /
• pp.55-64
• /
• 1992

This study investigated the effect of porcelain primer on bonding of coomposite resin to porcelain surface. In order to test the bond strength between porcelain and composite resin, porcelain cylinders were embedded in acrylic resin, and polished with 240grit silicone caqrbide paper. The specimens were divided into twelve groups. All specimens were treated with three porcelain primers and bonded with five composite resins. All test groups were stored in $37^{\circ}C$ distilled water for 48hours. Shear bond strengths were measured with Instron(Model 4201) at a cross-head speed of 1mm/min. The obtained results were as follows : 1. Scotchprime/Silux II group and BISCO Porcelain Primer/Bisfill group showed significant higher bond strengths than Clearfil Porcelain Primer/photo Clearfil Bright group(p<0.05). And there was no significant differences in bond strengths between Scotchprime/Silux II group and BISCO Porcelain Primer/Bisfill group(p>0.05). 2. When composite resins were used with Scotchprime, the bond strengths were decresed Silux II$(16.68{\pm}3.35MPa)$, Bisfil$(16.23{\pm}4.54MPa)$, Poly-Fill$(14.74{\pm}4.08MPa)$, Photo Clearfil Bright$(13.75{\pm}2.89MPa)$ and Pekalux$(14.74{\pm}4.08MPa)$ in order, but there was no statistical significance(p>0.05). 3. When composite resins were used with BISCO Porcelain Primer, the bond strength were decreased Bisfil$(16.17{\pm}1.60MPa)$, Silux II$(12.13{\pm}2.37MPa)$, Poly-Fill$(10.78{\pm}1.99MPa)$, Photo Cleafil Bright $(9.91{\pm}4.59MPa)$ and Pekalux$(7.36{\pm}2.16MPa)$ in order, but there was no statistical significance(p>0.05). 4. Silux II, Photo Clearfil Bright and Poly-Fill used with Scotchprime showed significant higher bond strengths than BISCO Porcelain Primer(p>0.05).

• Steel and Composite Structures
• /
• 제52권2호
• /
• pp.165-182
• /
• 2024

Grouted sleeve splice (GSS) is an effective type of connection applied in the precast concrete structures as it has the advantages of rapidly assembly and reliable strength. To decrease the weight and cost of vertical rebar connection in precast shear walls, a light-weight sleeve is designed according to the thick-cylinder theory. Mechanical behaviour of the light-weighted GSS is investigated through experimental analysis. Two failure modes, such as rebar fracture failure and rebar pull-out failure, are found. The load-displacement curves exhibit four different stages: elastic stage, yield stage, strengthening stage, and necking stage. The bond strength between the rebar and the grout increases gradually from outer position to inner position of the sleeve, and it reaches the maximum value at the centre of the anchorage length. A finite element model predicting the mechanical properties of the light-weighted GSS is developed based on the Concrete Damage Plasticity (CDP) model and the Brittle Cracking (BC) model. The effect of the rebar anchorage length is significant, while the increase of the thickness of sleeve and the grout strength are not very effective. A model for estimating ultimate load, including factors of inner diameter of sleeves, anchorage length, and rebar diameter, is proposed. The proposed model shows good agreement with various test data.

• Journal of Welding and Joining
• /
• 제16권5호
• /
• pp.100-107
• /
• 1998

This paper describes fluxless soldering of reflow soldering process using solder foil instead of solder pastes. There is an increasing demand for the reliable solder connection in the recent high density microelectronic components technologies. And also, it is problem fracture of an Ozone layer due to freon as which is used to removal of remained flux on the substrate. This paper discussed joining phenomena, boudability and joining processes of microelectronics devices, such as between outer lead of VLSI package and copper pad on a substrate without flux. The shear strength of joints is 8 to 13 N using Sn/Pb (63/37 wt.%) solder foil with optimum joining conditions, meanwhile, in case of using Sn/In (52/48 wt.%) solder foil, it is possible to bond with low heating temperature of 550 K, and accomplish to high bonding strength of 25N in condition heating temperature of 650K. Finally, this paper experimentally shows fluxless soldering using solder foil, and accomplishes key technology of microsoldering processes.

• 대한치과교정학회지
• /
• 제42권1호
• /
• pp.17-22
• /
• 2012

Objective: To study and compare the effects of different demineralization-inhibition methods on the shear bond strength (SBS) and fracture mode of an adhesive used to bond orthodontic brackets to demineralized enamel surfaces. Methods: Eighty freshly extracted, human maxillary premolars were divided into 4 equal groups and demineralized over the course of 21 days. Brackets were bonded to the demineralized enamel of teeth in Group 1. In Group 2, bonding was performed following resin infiltration ($ICON^{(R)}$, DMG, Hamburg, Germany). Before bonding, pre-treatment with acidulated phosphate fluoride (APF) or solutions containing casein phosphopeptide-amorphous calcium phosphate with 2% neutral sodium fluoride (CPP-ACP/wF) was performed in Groups 3 and 4, respectively. The SBS values of the brackets were measured and recorded following mechanical shearing of the bracket from the tooth surface. The adhesive remnant index (ARI) scores were determined aft er the brackets failed. Statistical comparisons were performed using one-way ANOVA, Tukey's post-tests, and G-tests. Results: Significant differences were found in some of the intergroup comparisons of the SBS values (F = 39.287, p < 0.001). No significant differences were found between the values for the APF-gel and control groups, whereas significantly higher SBS values were recorded for the resin-infiltrated and CPP-ACP/wF-treated groups. The ARI scores were also significantly different among the 4 groups (p < 0.001). Conclusions: Tooth surfaces exposed to resin infiltration and CPP-ACP/wF application showed higher debonding forces than the untreated, demineralized surfaces.

• The Journal of Advanced Prosthodontics
• /
• 제7권2호
• /
• pp.85-92
• /
• 2015

PURPOSE. This study aimed to investigate the efficacy of cleaning solutions on saliva-contaminated zirconia in comparison to air-abrasion in terms of resin bonding. MATERIALS AND METHODS. For saliva-contaminated air-abraded zirconia, seven cleaning methods)-no contamination (NC), water-spray rinsing (WS), additional air-abrasion (AA), and cleaning with four solutions (Ivoclean [IC]; 1.0 wt% sodium dodecyl sulfate [SDS], 1.0 wt% hydrogen peroxide [HP], and 1.0 wt% sodium hypochlorite [SHC])-were tested. The zirconia surfaces for each group were characterized using various analytical techniques. Three bonded resin (Panavia F 2.0) cylinders (bonding area: $4.5mm^2$) were made on one zirconia disk specimen using the Ultradent jig method [four disks (12 cylinders)/group; a total of 28 disks]. After 5,000 thermocycling, all specimens were subjected to a shear bond strength test with a crosshead speed of 1.0 mm/minute. The fractured surfaces were observed using an optical and scanning electron microscope (SEM). RESULTS. Contact angle measurements showed that groups NC, AA, IC, and SHC had hydrophilic surfaces. The X-ray photoelectron spectroscopy (XPS) analysis showed similar elemental distributions between group AA and groups IC and SHC. Groups IC and SHC showed statistically similar bond strengths to groups NC and AA (P>.05), but not groups SDS and HP (P<.05). For groups WS, SDS, and HP, blister-like bubble formations were observed on the surfaces under SEM. CONCLUSION. Within the limitations of this in vitro study, some of the cleaning solutions (IC or SHC) were effective in removing saliva contamination and enhancing the resin bond strength.