• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.801-806
• /
• 2008

Large quantity of bending deformation as well as rotating torque fluctuation at the balance shaft are main struggles during the operation in a high speed rotation and thereby, two issues should be cleared at the design process of balance shaft module. Since two issues are highly related with balance shaft itself and particularly much sensitive to the location of both supporting bearing and unbalance mass, the design strategy on balance shaft should be investigated at the aspect of controlling two critical issues at the early stage of balance shaft design. To tackle two main problems, the formulation of objective function that minimizes critical issues, both bending deformation as well as torque fluctuation, is suggested to derive the optimal information on balance shaft. Then, optimal informations are reviewed at the practical logics and the guideline at the selection of locations, both supporting bearing and unbalance mass, is addressed at the final chapter.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.248-253
• /
• 2009

The propulsion system which apply the diesel engine with reduction gear as prime mover, generally installs the elastic coupling between engine and intermediate shaft, This coupling can isolate the vibratory torque excited by diesel engine, or the excess transient torque and moment occurring by external impact. So, diesel engine and reduction gear can safely operate by elastic coupling. Unfortunately, the elastic coupling for skimmer vessel was repeatedly broken by unknown vibration during the sea trial In this paper, the authors are searching for the possibilities and causes of the elastic coupling failure, via the global vibration measurement and the past incident investigation.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.12 s.255
• /
• pp.1596-1602
• /
• 2006

In this paper, a hybrid sensor is proposed that has two capabilities: the first is to sense longitudinal or flexural transient vibration signals selectively which are transmitted along the target shaft, and the second to measure the rotating speed of the shaft. All measurements are made in a non-contact manner since this sensor uses magnetostriction as its measuring principle. The signal selection between two vibration modes requires only electrical switching operations and the switching between these two sensing capabilities-vibrations and rotational speed-are accomplished by a very simple mechanical operation. To verify the capabilities of the proposed sensor, a prototype sensor is fabricated and the experiments are made. The results show this sensor can embody two sensing capabilities in one sensor configuration.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.11a
• /
• pp.784-789
• /
• 2000

Equations of motion are derived and solved using the finite element method substructure synthesis for the disk-spindle system with rigid spindle and flexible shaft. The disk is modeled as a flexible spinning disk by Kirchhoff plate theory and von Karman nonlinear strain. The spindle supporting the flexible disk is modeled as a rigid body to consider its complex geometry. The stationary shaft supporting the rotating disk-spindle-bearing system is modeled by Euler beam, and the ball bearings are modeled as the stiffness matrix with 5 degrees of freedom. Developed theory is applied to analyze the vibration characteristics of a 3.5" HDD and a 2.5" HDD, respectively, and modal tests are performed to verify the simulation results. This paper shows that the developed theory can be effectively applied to the rotating disk-spindle system with the spindle of complex shape.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.540-545
• /
• 2008

The design on balance shaft module is performed based on the target specification of engine module as well as the its own dynamic nature under a high speed rotation. However, the specific information for engine module is not always available for non-motor companies even though a reliable analytical result should be attached in the conceptual design process or more detail works. In this paper, the analysis on balance shaft module, both each parts or module itself, is suggested to estimate the performance on the target component with respect to durability and NVH without any consideration of a engine module. This methodology could modify the nominal balance shaft model before the production of prototype such that cost reduction as well as time saving can be expected during design process of balance shaft module.

• Journal of KSNVE
• /
• v.8 no.3
• /
• pp.477-484
• /
• 1998

An analytical procedure on the base of the substructure synthesis and assumed modes method is developed to investigate the flexibility effect of bladed disk assembly on vibrational modes of flexible rotor system. In modeling the system, Coriolis forces, gyroscopic moments, and centrifugal stiffening effects are taken into account. The coupled vibrations between the shaft and bladed disk are then extensively investigated through the numerical simulation of simplified models, with varying the shaft rotational speed and the prewist and stagger angles of the blade. It is found that the Coriolis and inertia forces and the inertia torque, which are induced by the one nodal diameter modes of the bladed disk and vary depending upon the stagger and prewist angles, lead to the coupled motions of the shaft and the bladed disk.

• Explosives and Blasting
• /
• v.14 no.3
• /
• pp.3-9
• /
• 1996

The scope of this cable works was as follows, it was drilled two shafts, NO. 1 shaft (${\phi}6.8m{\times}31m$), NO.2 shaft (${\phi}6.8m{\times}33m$), ) and it was connected two shaft in Tunneling. The first, it was needed to investigate the surey of influenced of vibration and noise by blastig to near by housing structure. 2nd, it was essential to decide the boundary line of influenced for agriculture water and portable water, by draw down of underground water. Blasting works has been done successfully without any problem, but by draw down of underground water, with in 250m level from #1 shaft, agriculture well drilled 8 place and portable water well drilled 7 place for near by farmers.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.17 no.12
• /
• pp.1201-1207
• /
• 2007

The Timoshenko beam theories are used to model the rotating shaft. The nondimensional equations of motion for the rotating shaft subjected to moving mass and compressive axial forces are derived by using Hamilton's principle. Influence of system parameters such as the speed ratio. the mass ratio and the Rayleigh coefficient is discussed on the response of the moving system. The effects of compressive axial forces are also included in the analysis. The results are presented and compared with the available solutions of a rotating shaft subject to a moving mass and a moving load.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.6
• /
• pp.896-906
• /
• 1997

The effect of duplicate flexible disks on the vibrational modes of a flexible rotor system is investigated by using an anlytical method based on the assumed modes method. The rotor model to be analyzed consists of duplicate disks on a flexible shaft. In modeling the system, centrifugal stiffening and disk flexibility effects are taken into account. To demonstrate the effectiveness of the method, a hard disk drive spindle system commonly used in personal computers and a simple flexible rotor system with two disks are selected as examples. In particular, the dynamic coupling between the vibrational modes of the shaft and the duplicate disks is investigated with the shaft rotational speed varied.

• Transactions of Materials Processing
• /
• v.12 no.7
• /
• pp.654-661
• /
• 2003

A monobloc TDS(Tube Drive Shaft) has been developed by using the rotary swaging process which is one of the incremental forming process. In order to estimate the developed TDS performance characteristics such as natural frequency, strength, stiffness and mass, finite element analysis has been carried out using commercial software, MSC/NASTRAN. The calculated performance characteristics have been compared with analysis results of SDS(Solid Drive Shaft) to know how much improve the performance characteristics. Also the sensitivity analyses of design parameters for the tube length and diameter have been performed. From the analysis results, it was found that the TDS allowed for a high frequency and could be designed to be much lighter than SDS. This advantage can give possibility to tune the NVH (Noise-Vibration-Harshness) characteristics.