• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1996년도 추계학술대회 논문집
• /
• pp.982-986
• /
• 1996

The development of a high power BLDC servo system for a control of the large scale mechanical system is presented. Using DSP TMS320C30, a control unit which is suitable for motor drive system, is developed. Also, based on the developed control unit, BLDC drive system for the speed control is constructed. The algorithms of the vector control, current control, and speed control is implemented using TMS320C30 Software Development Tool. The developed high power BLDC motor drive system is applied to the large scale mechanical system and its feasibility is verified through the experimental results.

• 대한기계학회논문집
• /
• 제17권1호
• /
• pp.101-111
• /
• 1993

본 연구에서는 제안된 뉴로-퍼지 제어기를 사용하여 유압 서보 시스템을 제어 하고 학습하기 위한 구조로써 유압 서보 시스템의 모델링을 위한 추가적인 노력이 필 요없는 feedback error learning 구조물 채택하였다. 학습 과정에서 필요한 유압 서 보 시스템의 입-출력 사이의 감도(sensitivity)의 효과는 학습 계수에 포함된다. 이 러한 형태의 제어기가 유압 서보 시스템 제어에 유용하게 적용될 수 있다는 것을 보이 기 위해서 불확실성과 높은 비선형성 뿐만아니라 외란의 영향을 받는 유압 서보 시스 템을 대상으로 시뮬레이션을 수행했다. 시뮬레이션 결과에 의하면 제안된 뉴로-퍼지 제어기는 수학적인 모델을 기초로한 기존의 제어 알고리즘에 비해 쉽게 구성할 수 있 고 높은 정밀도, 빠른 학습 속도를 얻을 수 있는 장점을 가지고 있음을 알 수 있다.

• 한국자동차공학회논문집
• /
• 제21권5호
• /
• pp.169-175
• /
• 2013

CRDi technology of diesel engine was developed from in the early 2000s due to a need to increase fuel efficiency and environment care. Especially, high-pressure fuel injection system in CRDi system which has a fuel injection unit including an injector, a fuel pump and common-rail, etc. becomes possible to make the exhaust gas clean as well as power improvement. In this study, comparison of dynamic characteristics of servo-hydraulic piezo-driven injector with 3-way and bypass-circuit type was analyzed by using the AMESim code. As results of this study, it found the bypass-circuit inside servo-hydraulic piezo injector can cause a faster injection response than that of the 3-way type. Also it was shown that bypass-circuit type had better control capability due to hydraulic bypass system.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제52권12호
• /
• pp.616-623
• /
• 2003

Conventional P/PI speed controller of today's servo drives should be manually tuned the controller switching set-point by trial-and-errors, which may translate the drive system down-time and loss of productivity. The adjustable drive performance is heavily dependent on the quality of the expert knowledge and becomes inadequate in applications where the operating conditions change in a wide range, i.e., tracking command, acceleration/deceleration time, and load disturbances. In this paper, the demands on simple controls/setup are discussed for industry servo drives. Analyzing the frequency content of motor torque command, P/PI control mode switching is automatically performed with some prior knowledge of the mechanical dynamics. The dynamic performance of the proposed scheme assures a desired tracking response curve with minimal oscillation and settling time over the whole operating conditions. For comprehensive comparison of traditional P/PI control scheme, extensive test is carried out on actual servo system.

• 제어로봇시스템학회논문지
• /
• 제6권1호
• /
• pp.25-34
• /
• 2000

In this paper, we design a H^\infty servo controller for gauge control of tandem cold mill. To improve the performance of the AGC(Aotomatic Gauge Control) system based on the Taylor linearized model of tandem cold mill, the H^\infty servo controller is designed to satisfy robust stability, disturbance attenuation and robust tracking properties. The H^\infty servo controller problem is modified as an usual H^\infty control problem, and the solvability condition of the H^\infty servo problem depends on the solvability of the modified H^\infty control problem. Since this modified problem does not satisfied standard assumptions for the H^\infty control problem, it is solved by an LMI(Linear Matrix Inequality) technique. Consequently, the comparison between the H^\infty servo controller and the existing PID/FF(FeedForward) controller shows the usefulness of this study.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.836-839
• /
• 2003

A pneumatic servo valve which is widely applied in industrial field. And It is consist of force motor, spool ＆ sleeve and servo controller. In this study. we developed the force motor which is consume to low power for a pneumatic servo valve. We could reduce the number of turn of the solenoid by using ferromagnetic permanent magnet and took different direction of each other using one coil instead of two coil. we modeled a system consisting of various electro-mechanical subsystems. The appropriateness of the model was verified by simulation. The simulation model resolved the motion of spool, the winding current and the magnetic force. Also, we calculated the displacement and velocity of the spool, flux contour line, b vector. flux density. flux linkage, back EMF etc.

• Journal of Welding and Joining
• /
• 제23권3호
• /
• pp.40-46
• /
• 2005

Air gun has been one of the good tools to press two sheet metals. However, it is not easy to control the acting force precisely. A Servo-gun is a good tool to control the acting force on the workpiece comparing with the air gun. Servo-gun has a higher tensile shear strength and lower indentation depth as well as smaller spatter. Dynamic resistance was obtained according to the acting force and welding current. As the acting force was changed during welding, the welding quality was increased.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권2호
• /
• pp.185-191
• /
• 2004

This study describes the scheme of vector drive system without speed sensor for AC servo motor using theory of a flux observer and based on the field oriented vector control. The new method of speed estimation is presented from operate with the position and magnitude of the secondary flux which obtain from the voltage reference and detected current. As the estimated speed is settled by the flux and the machine-specific parameters. this method don't need to adjust the gain of the parameter. Based on the derived theory for vector control. the scheme for sensorless vector drive of AC servo motor is designed and realized. And the experiment verifies it passable to realize the sensorless vector drive based on a field-oriented type.

• 드라이브 ㆍ 컨트롤
• /
• 제14권4호
• /
• pp.61-70
• /
• 2017

In this study, an extended-state-observer (ESO) based non-linear servo control is introduced for an electro-hydrostatic actuator (EHA). Almost hydraulic systems not only are highly non-linear system that has mismatched uncertainties and external disturbances, but also can not measure some states. ESO that only use an output signal can be used to compensate these uncertainties and estimate unmeasurable states. To improve the position tracking performance, the barrier Lyapunov function (BLF) that can guarantee an output tolerance is introduced for the position tracking error signal of back stepping control procedures. Finally, the proposed servo control is compared with the proportional-integral (PI) control.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.301-306
• /
• 2004

In this study, Dual servo mechanism with VCM(Voice Coil Motor) and PZT is designed for a high precision force and position control. We designed the VCM actuator and dual servo mechanism with leaf spring. VCM actuators, with their high linearity, simple structure, low weight, and high efficiency, are increasingly being used in micro-positioning applications. There are many kinds of VCM with a structure. VCM actuators are divided into two types by moving parts. One is moving magnet type and the other moving coil type. We described the properties of these two types of VCM. Design parameters of VCM are defined through the FEM simulation analysis of magnetic field and dynamic model of dual servo mechanism. These researches help to for decreasing loss in the air gap of VCM. We present dual servo mechanism is effective mechanism for a force control in hi h precision, properties of designed VCM.