• Proceedings of the KIEE Conference
• /
• 1998.07g
• /
• pp.2473-2475
• /
• 1998

In this paper, we implemented RS232C serial communication by the 2 wires(Data,GND), and multiple access, by the applying Collision Sensing Multiple Access(CSMA) Protocol. Multiple access is implemented by assigning a unique ID to each controller. The multiple access control operation starts by sending a command packet from a host to another host and the command packet is composed of ID bytes of source and target host computer, data bytes and the check sum, byte. In host computer, after sending command packet, the collision from loop back data. If collision is detected, it means a command packet was collided with another command packet for another host. The packet communication of the controller enables the multiple acces of the controller through the common serial data link. The application of this serial communication through CSMA protocol and the usage of two wires, have an effect on saving the wires and convenient of layout work.

• ETRI Journal
• /
• v.20 no.1
• /
• pp.16-27
• /
• 1998

In this paper, we consider the acquisition performance of an IS-95 reverse link access channel slot as a function of system design parameters such as postdetection integration length and the number of access channel message block repetitons. The uncertainty region of the reverse link spreading codes compared to that of forward link is very small, since the uncertainty region of the reverse link is determined by a cell radius. Thus, the parallel acquisiton technique in the reverse link is more efficient than a serial acquisition technique in terms of implementation and of acquisition time. The parallel acquisition is achieved by a bank of N parallel I/Q noncoherent correlator are analyzed for band-limited noise and the Rayleigh fast fading channel. The detection probability is derived for multiple correct code-phase offsets and multipath fading. The probability of no message error is derived when rake combining, access channel message block combining, and Viterbi decoding are applied. Numerical results provide the acquisition performance for system design parameters such as postdetection integration length and number of access channel message block repetitions in case of a random access on a mobile station.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.7
• /
• pp.63-70
• /
• 2004

This paper describes the link layer and physical layer of the Serial ATA which is the next generation for parallel ATA specification that defines data transfer between PC and peripheral storage devices. The link layer consists of CRC generation/error detection, 8b/10b decoding/encoding, primitive generation/detection block. For the physical layer, it includes CDR(Cock Data Recovery), transmission PLL, serializer/de-serializer. It also includes generation and receipt of OOB(Out-Of-Band) signal, impedance calibration, squelch circuit and comma detection/generation. Additionally, this chip includes TCB(Test Control Block) and BIST(Built-In Selt Test) block to ease debugging and verification. It is fabricated with 0.18${\mu}{\textrm}{m}$ standard CMOS cell library. All the function of the link layer operate properly. For the physical layer, all the blocks operate properly but the data transfer is limited to the 1.28Gbps. This is doe to the affection or parasitic elements and is verified with SPICE simulation.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.631-637
• /
• 2005

This paper presents a stiffness analysis method for a low-DOF parallel manipulator, which takes into account of elastic deformations of joints and links. A low-DOF parallel manipulator is defined as a spatial parallel manipulator which has less than six degrees of freedom. Differently from the case of a 6-DOF parallel manipulator, the serial chains in a low-DOF parallel manipulator are subject to constraint forces as well as actuation forces. The reaction forces due to actuations and constraints in each limb can be determined by making use of the theory of reciprocal screws. It is shown that the stiffness model of an F-DOF parallel manipulator consists of F springs related to the reciprocal screws of actuations and 6-F springs related to the reciprocal screws of constraints, which connect the moving platform to the fixed base in parallel. The $6{times}6$ stiffness matrix is derived, which is the sum of the stiffness matrices of actuations and constraints. The six spring constants can be precisely determined by modeling the compliance of joints and links in a serial chain as follows; the link can be considered as an Euler beam and the stiffness matrix of rotational or prismatic joint can be modeled as a $6{times}6$ diagonal matrix, where one diagonal element about the rotation axis or along the sliding direction is zero. By summing the elastic deformations in joints and links, the compliance matrix of a serial chain is obtained. Finally, applying the reciprocal screws to the compliance matrix of a serial chain, the compliance values of springs can be determined. As an example of explaining the procedure, the stiffness of the Tricept parallel manipulator has been analyzed.

• 제어로봇시스템학회:학술대회논문집
• /
• 1991.10a
• /
• pp.337-341
• /
• 1991

Fieldbus is a low level serial digital network which will be used for factory automation. This paper describes lower layer implementation of a Fieldbus network interface. Physical layer provides hardware interface between IBM-PC and Fieldbus. Also, physical layer uses manchester coding, shielded twisted pair lines and RS-485 electrical standard. Data link layer includes Intel's iDCX96 real time executive for 8797 one chip microcontroller and Fieldbus data link protocol software.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.634_635
• /
• 2009

Large aluminium electrolytic capacitors are widely used in inverter systems for smoothing dc-link voltage. If capacitors in dc-link are deteriorated by ageing, dc-link voltage is fluctuated by lessened capacitance and their bodies are heated by raised ESR(equivalent serial resistance) and finally system faults can be occurred. In this paper, on-load ageing test method of electrolytic capacitor in inverter system is proposed and test results are shown.

• ETRI Journal
• /
• v.34 no.1
• /
• pp.122-125
• /
• 2012

A video signal through a high-density optical link has been demonstrated to show the reliability of optical link for high-data-rate transmission. To reduce optical point-to-point links, an electrical link has been utilized for control and clock signaling. The latency and flicker with background noise occurred during the transferring of data across the optical link due to electrical-to-optical with optical-to-electrical conversions. The proposed synchronization technology combined with a flicker and denoising algorithm has given good results and can be applied in high-definition serial data interface (HD-SDI), ultra-HD-SDI, and HD multimedia interface transmission system applications.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.1
• /
• pp.60-68
• /
• 1998

Parallel link manipulators have an ability of more precise positioning than serial open-loop manipulators. However. general parallel link manipulators have been restricted to the real applications since they have limited workspace due to interference among actuators. In this study, we suggest a closed-loop manipulator with 6 degrees-of-freedom and with enlarged workspace. It consists of two parts for minimizing the interference among actuators. One part is lower structure with planar 3 degrees-of-freedom and the other is upper one with spatial 3 degrees-of-freedom. Forward kinematics and inverse kinematics are solved, research about singularity points are carried out and workspace is evaluated. The comparison of workspace between Stewart platform, which is the typical parallel link manipulator, and the suggested manipulator shows that the workspace of the latter is wider than that of the former. Especially, simulation results also show that the suggested manipulator is more suitable when there needs rotation in the end-effector.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.391-392
• /
• 2020

본 논문은 3레벨 정류기와 직렬 입력, 병렬 출력 LLC 컨버터가 연결된 전원 장치의 DC-Link 전압 불평형 제어에 관해 분석한다. 일반적으로 380Vac 입력을 가지는 3레벨 부스트 기반 정류기는 출력 전압을 700Vdc 이상으로 제어한다. 또한, 3레벨 컨버터는 두 개의 직렬 출력 커패시터를 가지며, 불균형 해소를 위한 제어 또는 물리적 불평형 해소 소자가 요구된다. 스위칭 신호를 공유하는 두 개의 LLC 컨버터가 연결된 시스템에 DC-Link 불평형 전압 제어가 적용되면 전력의 쏠림 현상이 발생한다. 본 논문은 제시된 시스템에서 전력의 쏠림 현상에 대해 그 원인을 분석하고 실험으로 검증한다.

• The Journal of Korea Robotics Society
• /
• v.11 no.3
• /
• pp.163-171
• /
• 2016

A modular manipulator in serial-chain structure usually consists of a series of modularized revolute joint and link modules. The geometric shapes of these modules affect the number of possible configurations of modular manipulator after assembly. Therefore, it is important to design the geometry of the joint and link modules that allow various configurations of the manipulators with minimal set of modules. In this paper, a new 1-DoF(degree of freedom) joint module and simple link modules are designed based on a methodology of joint configurations using a series of Rotational(type-R) and Twist(type-T) joints. Two of the joint modules can be directly connected so that two types of 2-DoFs joints could be assembled without a link module between them. The proposed geometries of joint and link modules expand the possible configurations of assembled modular manipulators compared to existing ones. Modular manipulator system of this research can be a cornerstone of user-centered markets with various solution but low-cost, compared to conventional manipulators of fixed-configurations determined by the provider.