• Journal of the Korean earth science society
• /
• v.30 no.2
• /
• pp.234-246
• /
• 2009

Characteristics of speckle errors of Sea-viewing Wide Field-of-view Sensor (SeaWiFS) chlorophyll-${\alpha}$ concentration were analyzed, and its causes were investigated by using SeaWiFS data in the East Sea from September 1997 to December 2007. The speckles with anomalously high concentrations were randomly distributed and showed remarkably high bias of greater than $10mg/m^3$, compared with their neighboring pixels. The speckles tended to appear frequently in winter, which might be related to cloud distribution. Ten-year averaged cloudiness of winter was much higher over the southeastern part, with frequent speckles, than the northwestern part of the East Sea. Statistical analysis results showed that the number of the speckles was increased as cloudiness increased. Normalized water-leaving radiance of the speckle pixel was considerably low at the short wavelengths (443, 490, and 510 nm), whereas the radiance at 555 nm band was normal. These low measurements produced extraordinarily high concentration from the chlorophyll-${\alpha}$ estimation formula. This study presented the speckle errors of SeaWiFS chlorophyll-${\alpha}$ concentration in the East Sea and suggested that more reliable chlorophyll-${\alpha}$ data based on appropriate ocean color remote sensing techniques should be used for the oceanic application researches.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.12
• /
• pp.2641-2646
• /
• 2009

The more growing on home automation system at automatic control, the more efficiency required for energy consumption and for recycling energy in near future. Heating is essential in general apartment. Heating method is two types in apartment. One uses electricity, and other one uses warm water. If use electricity, is not efficient by rise of electric charges. But, It can reduce much in expense aspect, if use warm water. When use warm water, temperature of warm water is not equal from all pipe parts. Therefore, indoor tempera can be unequal with set point. Solution of these problems is as following. Temperature sensor in warm water attach pipe. The measured temperature transmits by real time. Temperature of warm water controls in receiver side. In this paper, we propose an automatic temperature transmission system for the heating pipe at home, that is a low-power based, and supply the energy source from a small AC motor resided in bottom cement mortal. The proposed system is used in power mechanism from a collision process of water-jet using propeller water-difference and also designed a CPU module by Atmega8 at ATMEL co., Inc. and a communication module by CC1020 at Chipcon co., Inc.

• Journal of Sensor Science and Technology
• /
• v.25 no.6
• /
• pp.440-446
• /
• 2016

This study introduces the characteristics of current-voltage (I-V) and impedance variance for $ZnO-Zn_2BiVO_6-Co_3O_4$ (ZZCo), which is sintered at $900^{\circ}C$, according to temperature changes. ZZCo varistor demonstrates dramatic improvement of non-linear coefficient, ${\alpha}=66$, with lower leakage current and higher insulating resistivity than those of ZZ ($ZnO-Zn_2BiVO_6$) from the aspect of I-V curves. While both systems are thermally stable up to $125^{\circ}C$, ZZCo represents a higher grain boundary activation energy with 1.05 eV and 0.94 eV of J-E-T and from IS & MS, respectively, than that of ZZ with 0.73 eV and 0.82 eV of J-E-T and from IS & MS, respectively, in the region above $180^{\circ}C$. It could be attributed to the formation of $V^*_o$(0.41~0.47 eV) as dominant defect in two systems, as well as the defect-induced capacitance increase from 781 pF to 1 nF in accordance with increasing temperature. On the other hand, both the grain boundary capacitances of ZZ and ZZCo are shown to decrease to 357 pF and 349 pF, respectively, while the resistances systems decreased exponentially, in accordance with increasing temperature. So, this paper suggests that the application of newly formed liquid phases as sintering additives in both $Zn_2BiVO_6$ and the ZZCo-based varistors would be helpful in developing commercialized devices such as chips, disk-type ZnO varistors in the future.

• Journal of Intelligence and Information Systems
• /
• v.20 no.1
• /
• pp.1-14
• /
• 2014

Both researchers and practitioners are showing an increased interested in interactive exhibition services. Interactive exhibition services are designed to directly respond to visitor responses in real time, so as to fully engage visitors' interest and enhance their satisfaction. In order to install an effective interactive exhibition service, it is essential to adopt intelligent technologies that enable accurate estimation of a visitor's emotional state from responses to exhibited stimulus. Studies undertaken so far have attempted to estimate the human emotional state, most of them doing so by gauging either facial expressions or audio responses. However, the most recent research suggests that, a multimodal approach that uses people's multiple responses simultaneously may lead to better estimation. Given this context, we propose a new multimodal emotional state estimation model that uses various responses including facial expressions, gestures, and movements measured by the Microsoft Kinect Sensor. In order to effectively handle a large amount of sensory data, we propose to use stratified sampling-based MRA (multiple regression analysis) as our estimation method. To validate the usefulness of the proposed model, we collected 602,599 responses and emotional state data with 274 variables from 15 people. When we applied our model to the data set, we found that our model estimated the levels of valence and arousal in the 10~15% error range. Since our proposed model is simple and stable, we expect that it will be applied not only in intelligent exhibition services, but also in other areas such as e-learning and personalized advertising.

• Journal of Energy Engineering
• /
• v.24 no.1
• /
• pp.114-122
• /
• 2015

In the high convective gas flow condition, irregular shaped water waves from which droplet entrainment occurs are generated under horizontally stratified two-phase flow condition. KAERI proposed a new mechanistic droplet entrainment model based on the momentum balance equation consisting of the shear stress, surface tension, and gravity forces. However, this model requires correlation or experimental data of several physical parameters related to the wave characteristics. In the present study, we tried to measure the physical parameters such as wave slope, wave hypotenuse length, wave velocity, wave frequency, and wavelength experimentally. For this, an experiment was conducted in the horizontal rectangular channel of which width, height, and length are, respectively, 40 mm, 50 mm, and 4.2 m. In the present test, the working fluids are chosen as air and water. The PIV technique was applied not only to obtain images for phase interface waves but also to measure the velocity field of the water flow. Additionally, we developed the parallel wire conductance probe for the confirmation of wave height from PIV image. Finally, we measured the physical parameters to be used in the validation of new droplet entrainment model.

• Journal of Sensor Science and Technology
• /
• v.22 no.4
• /
• pp.244-248
• /
• 2013

The discovery of a two-dimensional electron gas (2DEG) in $LaAlO_3$ (LAO)/$SrTiO_3$ (STO) heterostructure has stimulated intense research activity. We suggest a new structure model based on $KNbO_3$ (KNO) material. The KNO thin films were grown on $TiO_2$-terminated STO substrates as a p-type structure ($NbO_2/KO/TiO_2$) to form a two-dimensional hole gas (2DHG). The STO thin films were grown on KNO/$TiO_2$-terminated STO substrates as an n-type structure to form a 2DEG. Oxygen pressure during the deposition of the KNO and STO thin films was changed so as to determine the effect of oxygen vacancies on 2DEGs. Our results showed conducting behavior in the n-type structure and insulating properties in the p-type structure. When both the KNO and STO thin films were deposited on a $TiO_2$-terminated STO substrate at a low oxygen pressure, the conductivity was found to be higher than that at higher oxygen pressures. Furthermore, the heterostructure formed at various oxygen pressures resulted in structures with different current values. An STO/KNO heterostructure was also grown on the STO substrate, without using the buffered oxide etchant (BOE) treatment, so as to confirm the effects of the polar catastrophe mechanism. An STO/KNO heterostructure grown on an STO substrate without BOE treatment did not exhibit conductivity. Therefore, we expect that the mechanics of 2DEGs in the STO/KNO heterostructures are governed by the oxygen vacancy mechanism and the polar catastrophe mechanism.

• Journal of Biosystems Engineering
• /
• v.41 no.4
• /
• pp.313-318
• /
• 2016

Purpose: This study measured and analyzed the PTO (power take off) torque of a transplanter according to the planting conditions during field operation. Methods: A torque measurement system was constructed with torque sensors to measure the torque of a PTO shaft, a measurement device to acquire sensor signals, and a power controller to provide power for a laptop computer. The field operation was conducted at four planting distances (26, 35, 43, and 80 cm) and two planting depths using the transplanter on a field with similar soil conditions. One-way ANOVA with planting distance and Duncan's multiple range test at a significance level of 0.05 were used to analyze the PTO torque. The torque ratio was calculated based on the minimum torque using the average PTO torque measured under each planting condition. Results: The average torques on the PTO shaft for planting distances of 26, 35, 43, and 80 cm at a low planting depth were 11.05, 9.07, 7.04, and 3.75 Nm, respectively; the same for planting distances of 26, 35, 43, and 80 cm at a middle planting depth were 12.20, 9.86, 7.94, and 4.32 Nm, respectively. When the planting distance decreased by 43, 35, and 26 cm, the torque ratio at a low planting depth increased by 88, 142, and 195%, respectively. When the planting distance decreased by 43, 35, and 26 cm, the torque ratio at the middle planting depth increased by 84, 128, and 182%, respectively. Conclusions: PTO torque fluctuated by planting distance and depth. Moreover, the PTO torque increased for short planting distances. Therefore, farmers should determine the planting conditions of the transplanter by considering the load and durability of the machine. The results of this study provide useful information pertaining to the optimum PTO design of the transplanter considering the field load.

• Journal of Korean Society for Geospatial Information Science
• /
• v.24 no.1
• /
• pp.61-68
• /
• 2016

Digital aerial images have been commonly used in a large scale map production owing to their excellent geometry, and high spatial and radiometric resolution in recent years. However, a quality verification process for acquired images should be preceded in order to secure the high precision and reliability of produced results. Several experimental studies to verify digital imaging systems have been vigorously researched by constructing permanent test field in abroad. On the other hand, it is urgently necessary to suggest a practical scheme for an image quality verification, because this related study and experiment are still in its early stage at home. Hence, this study aims to present an easy method to measure the spatial resolution of the image in a visual way using a portable Siemens star. The images used in the study were obtained with three different cameras, two frame array sensors of DMC, UltraCamXp and a linear array sensor of ADS80. The Siemens star target appeared in every image is extracted and then the spatial resolution of image is compared with theoretical GSD(Ground Sample Distance) by a visual method. In addition, the change of spatial resolution depending on the location of the Siemens star from image center and flight direction and cross-flight direction is also compared and analyzed. As study results, while the theoretical GSDs of images taken with each camera are about 6~9cm, the visual resolutions are 1.2~1.3 times as great as the theoretical ones.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.28 no.1
• /
• pp.123-133
• /
• 2018

Cyber-Physical System (CPS) is a system in which a physical system and a cyber system are strongly integrated. In order to operate the target physical system stably, the CPS constantly monitors the physical system through the sensor and performs control using the actuator according to the current state. If a malicious attacker performs a forgery attack on the measured values of the sensors in order to conceal their attacks, the cyber system operated based on the collected data can not recognize the current operation status of the physical system. This causes the delay of the response of the automation system and the operator, and then more damage will occur. To protect the CPS from increasingly sophisticated and targeted attacks, countermeasures must be developed that can detect stealthy deception attacks. However, in the CPS environment composed of various heterogeneous devices, the process of analyzing and demonstrating the vulnerability to actual field devices requires a lot of time. Therefore, in this study, we propose a method of constructing the experiment environment of the PLCitM (PLC in the middle) which can verify the performance of the techniques to detect the CPS stealthy deception attack and present the experimental results.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.6
• /
• pp.1124-1131
• /
• 2006

The recent medical treatment guidelines and the development of information technology make hospitals reduce the expense in surrounding environment and it requires improving the quality of medical treatment of the hospital. Moreover, MIS, PACS(Picture Archiving and Communication System), OCS, EMR are also developing. Medical Information System is evolved toward integration of medical IT and situation is changing with increasing high speed in the ICT convergence. Mobile component refers to construct wireless system of hospital which has constructed in existing environment. Through RFID development in existing system, anyone can log on easily to internet whenever and wherever. It is the core technology to implement automatic medical processing system. This paper provides a basic review of RFID model, PACS application component services. In addition, designed and implemented database server's component program and client program of mobile application that recognized RFID tag and patient data in the ubiquitous environments. This system implemented mobile PACS that performed patient data based db environments, and so reduced delay time of requisition, medical treatment, lab.