• Composites Research
• /
• v.26 no.2
• /
• pp.99-104
• /
• 2013

The design of composite joint is important research area because they are often the weakest areas in composite structures. In this paper, the specimens with three paste thickness (0.2 mm, 0.6 mm, 4 mm) were manufactured in secondary bonding method and tested in two different loading direction condition. Also, the failure index of the L-type stiffener was calculated by the finite element method and compared with experimental results.

• Archives of Reconstructive Microsurgery
• /
• v.9 no.1
• /
• pp.80-87
• /
• 2000

Acute high speed accidents that results in full thickness skin defect and exposure of tendon, nerve, vessel and periosteum over denuded bone demands soft tissue coverage. Exposed bone often ensues chronic infection and requires free flap transplantation which surely covers defects in one stage operation and enhances transport of oxygen-rich blood and converts a non-osteogenic or partially osteogenic site into a highly osteogenic site, but exposed bone which had performed free flap transplantation sometimes necroses and needs secondary bone procedure. Scar contracture limits joint motion should be excised and covered with normal soft tissue to restore normal range of motion. Authors have performed the large latissimus dorsi myocutaneous free flap in 8 cases of extensive soft tissue defect and exposed bone lesion in the leg and 1 case of the flap was failed. The secondary ilizarov bone procedure was performed in 3 of 8 cases. 2 cases of large burn scar contracture and 1 case of posttraumatic scar contracture in lower extremity were restored with the large latissimus dorsi myocutaneous free flap. Authors concluded that large latissimus dorsi myocutaneous free flap is the most acceptable microvascular procedure in large soft tissue defect combined with exposed periosteum and bone requiring secondary bone procedure and in large burn scar contracture limiting knee joint motion.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.7 no.6
• /
• pp.1379-1397
• /
• 2013

We consider a system where a licensed radio spectrum is shared by multiple primary users(PUs) and secondary users(SUs). As the spectrum of interest is licensed to primary network, power and channel allocation must be carried out within the cognitive radio network so that no excessive interference is caused to PUs. For this system, we study the joint beamforming and power allocation problem via game theory in this paper. The problem is formulated as a non-cooperative beamforming and power allocation game, subject to the interference constraints of PUs as well as the peak transmission power constraints of SUs. We design a joint beamforming and power allocation algorithm for maximizing the total throughput of SUs, which is implemented by alternating iteration of minimum mean square error based decision feedback beamforming and a best response based iterative power allocation algorithm. Simulation results show that the algorithm has better performance than an existing algorithm and can converge to a locally optimal sum utility.

• The Journal of the Korean bone and joint tumor society
• /
• v.5 no.4
• /
• pp.235-238
• /
• 1999

Chondroblastoma of the patella is a uncommon benign neoplasm in the middle aged person. Furthermore, a hemorrhagic cystic change associated with chondroblastoma is extremely rare. We experienced a case of chondroblastoma which underwent hemorrhgic cystic change. A fiftyyear-old female patient has suffered from right knee joint pain for 1 month before. Dominant gross feature was hemorrhagic cyst which was not involved into the joint space. Soft tissue was curetted and it was diagnosed to be chondroblastoma. The case was treated with curettage and bone graft.

• Journal of International Academy of Physical Therapy Research
• /
• v.11 no.3
• /
• pp.2107-2112
• /
• 2020

Background: With the increasing elderly population, the need for gait analysis of these elderly individuals is also increasing. Most devices are costly and not portable; however, smartphones using built-in sensors capable of measuring motion and are easily available. Objectives: To examine the reliability and validity of knee joint angles of the elderly using smartphone measurements during walking. Design: Quasi-experimental research. Methods: Sixteen elderly people, aged 65+ and living in Daejeon and Chungbuk, South Korea, participated in the study. Electrogoniometers and smartphones were attached to the thigh and the side and front of the shank of each subject, respectively, using double-sided tape, an arm band, and an elastic band. Each subject completed two sets of at least seven gait cycles (14 steps). Results: Both the smartphones and electrogoniometers exhibited high agreement in terms of their primary and secondary measurements (ICC>.75). The agreement between the smartphones and electrogoniometers was also high in terms of both the primary and secondary measurements (ICC<.60). Conclusion: These results indicate that smartphones can be costly equipment cannot, even though they cannot completely replace existing clinical-grade devices. Their utility is emphasized herein for measuring knee joint angles of the elderly during walking.

• Composites Research
• /
• v.24 no.4
• /
• pp.48-54
• /
• 2011

The effect of moisture contents by salt water on the strength of composite single-lap bonded joints is investigated. The specimens were manufactured in an autoclave by secondary bonding and immersed in the 3.5% salt water of $71^{\circ}C$ for different durations to get various moisture contents; 0, 0.2, 0.5, 1.0, and 2.0%(saturation). A total of 80 joint specimens were tested for 5 different moisture contents and 2 temperature environments. Test results show that while the joint strengths after the saturation of moisture decrease compared to those of dry ones, the strengths of the pre-saturated joint up to 1.0% of moisture content increase in both room and elevated temperature conditions. It is also shown that the strengths of joints tested in elevated temperature are slightly higher than the strength in room temperature by 2-5% until the moisture content reaches 1 %. In contrast, the high temperature strength of the saturated joint is about 5% lower than the room temperature strength.

• Structural Engineering and Mechanics
• /
• v.21 no.6
• /
• pp.677-698
• /
• 2005

In engineering practice, tubular connections are usually assumed pinned or rigid. Recent research showed that tubular joints may exhibit non-rigid behavior under axial or bending loads. This paper is concerned with establishing a new classification for tubular joints and investigating the effect of joint rigidity on the global behavior of CHS (Circular Hollow Section) lattice girders. Parametric formulae for predicting tubular joint rigidities are proposed, which are based on the finite element analyses through systematic variation of the main geometric parameters. Comparison with test results proves the reliability of these formulae. By considering the deformation patterns of respective parts of Vierendeel lattice girders, the boundary between rigid and semirigid tubular connections is built in terms of joint bending rigidity. In order to include characteristics of joint rigidity in the global structural analysis, a type of semirigid element which can effectively reflect the interaction of two braces in K joints is introduced and validated. The numerical example of a Warren lattice girder with different joint models shows the great effect of tubular joint rigidities on the internal forces, deformation and secondary stresses.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.28-28
• /
• 2010

The secondary barrier of cargo containment for membrane LNG tank is composed of composite materials such as rigid triplex (rigid secondary barrier, RSB) and flexible triplex (flexible secondary barrier, FSB). RSB and FSB are adhered to each other using an epoxy adherent and the quality of the secondary barrier depends on the bonding strength between them. The bonding strength between RSB and FSB is greatly influenced by the surface condition of RSB prior to joining. In this study, the effect of surface condition prior to joining on the joint strength and the fracture mode occurred between RSB and FSB have been examined in order to establish a proper surface treatment method for improving the bonding strength at the temperature of $-170^{\circ}C$.

• Journal of Microbiology and Biotechnology
• /
• v.9 no.5
• /
• pp.562-567
• /
• 1999

Single-stranded DNA binding protein (SSB) is well-characterized as having a helix-destabilizing activity. The helix-destabilizing capability of SSB has been re-examined in this study. The results of restriction endonuclease protection assays and titration experiments suggest that the stimulatory effect of SSB on strand exchange acts by melting out the secondary structure which is inaccessible to RecA protein binding; however, SSB is excluded from regions of secondary structure present in native single-stranded DNA. Complexes of SSB and RecA protein are required for eliminating the secondary structure barriers under optimal conditions for strand exchange.

• Proceedings of the KIEE Conference
• /
• 1999.07a
• /
• pp.136-138
• /
• 1999

Linear Induction Motors (LIMs) with the long secondary conductor often have joints between the segmented secondary, which are specially used for magnetically levitated high-speed vehicle and elevators. In this paper, the dynamic characteristics of the LIM with joints in the secondary are investigated using the time-stepping finite element analysis. It is supposed that both aluminium conductor and back-iron have joint in the active zone during the analysis. As a result, thrust and normal force ripple which have effects on the motor dynamics and vibration are examined.