• Journal of the Korean Society of Combustion
• /
• v.9 no.2
• /
• pp.38-44
• /
• 2004

The evolution of incipient soot particles has been examined by high resolution electron microscopy (HRTEM) and elemental analyzer in ethylene-air inverse diffusion flames. Laser Induced Incandescence(LII) and laser scattering methods were introduced for examining the soot volume fraction and morphological properties in combustion generated soot qualitatively. Soot particles, collected by thermophoretic sampling, were analyzed by using HRTEM to examine the nano structure of precursor particles. HRTEM micrographs apparently reveal a transformation of condensed phase of semitransparent tar-like material into precursor particles with relatively distinct boundary and crystalline which looks like regular layer structures. During this evolution histories, C/H analysis was also performed to estimate the chemical evolution of precursor particles. The changes of C/H ratio of soot particles with respect to residence time can be divided into two parts: one is a very slowly increasing regime where tar-like materials are transformed into precursor particles (inception process) the other is an increasing region with constant rate where surface growth affects the increase of C/H ratio dominantly (surface growth process). These results provide a clear picture of a transition to mature soot from precursor materials.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.2076-2081
• /
• 2004

Future exhaust gas limits for diesel-driven passenger cars will force the automotive industry to significantly improve the performance of engine. Since modern common-rail injection systems deliver more degrees of freedom referring to the injection process, again the optimization of the injection process could offer a possibility to meet the exhaust gas limits. This study describes the characteristic the pilot spray structure of piezo-driven injector for a passenger car common-rail system to be applicable multiple injection caused by fast response rather than solenoid-driven injector. The piezo-driven injector is prototype injector with same needle chamber of solenoid injector and the solenoid-driven one is commercial injector. The pilot spray characteristic such as spray tip penetration, spray speed, spray angle were obtained by spray images, which is measured by the Mie scattering method with optical system for high-speed temporal photography. It was found that piezo-driven injector effected electric change as important factor and showed faster response than solenoid-driven injector.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.16 no.5
• /
• pp.126-133
• /
• 2017

This report investigates the stress distribution according to the location and shape change of the circular hole for the lightweight design of the cross beam of a railway passenger car and studies the lightweight design. To design a lightweight cross beam with a circular hole, we selected the non-circular crossbeam as a basic model, examined the stress distribution and displacement by position and determined the location, shape, size and quantity of the hole for light weight. We analyzed the effects of the position and shape of the hole on the maximum equivalent stress and displacement. The influencing factors were set as the design parameters, and the stress value was examined according to the variation of each variable. By considering the stress value according to the change of each variable and selecting the design parameter with the narrowest scattering value of the stress at each position of the hollow cross beam with various hole positions and shapes, we studied a cross beam with a circle hole under identical load condition to have an equal stress distribution to that of a non-circular cross beam.

• Journal of the Society of Naval Architects of Korea
• /
• v.44 no.4
• /
• pp.445-450
• /
• 2007

An optimum design process of the broad-band multi-layered radar absorbing material, using genetic algorithm, is established for the radar cross section reduction of a complex target, which consists of multiple reflection structures, such as surface warships. It follows the successive process of radar cross section analysis, scattering center analysis, radar absorbing material design, and reanalysis of radar cross section after applying the radar absorbing material. It is demonstrated that it is very effective even in the optimum design of the multi-layer radar absorbing material. This results from the fact that the three factors, i.e.. the incident angle range, broad-band frequencies, and maximum thickness can be simultaneously taken into account by adopting the genetic algorithm.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.6B
• /
• pp.1127-1135
• /
• 2000

The beamforming procedure in Adaptive Array Antenna System is affected by signal degradation and data rate due to DS-CDMA characteristics. Until this time, a lot of techniques are suggested to overcome this problems. This paper shows the simulation result about the beamforming performance of symbol level system that process slow data rate, compensated signal by despreading procedure in front of beamformer, and that of chip level system that process chip level signal without it. we analysis the performance using MSE, beam pattern, scattering points of beamformer output. chip level system is superior to symbol level system in time varying channel, while the performance of them didn't have difference in static channel.

• Design & Manufacturing
• /
• v.10 no.2
• /
• pp.34-38
• /
• 2016

In this paper, a transversely isotropic behavior of AZ31 Mg alloy produced by equal-channel angular pressing (ECAP) process was investigated through tensile test and microstructure observation. The effects of initial ECAP pass number on the anisotropic behavior and mechanical properties of the Mg alloy are evaluated after conventional direct extrusion test, which are carried out at a temperature of $200^{\circ}C$. As a result of the tensile test in three directions ($0^{\circ}$, $45^{\circ}$, and $90^{\circ}$ to the extrusion direction of the sheet) at room temperature, elongation of as-extruded AZ31 alloy(ECAP for 0 pass) showed an unusual anisotropic behavior depending on the extrusion direction although the yield strength and tensile strength are similar to the ECAPed AZ31 alloy. After ECAP for 4 passes at $200^{\circ}C$, microstructural observations of ECAPed magnesium alloy showed a significant grain refinement, which is leading to an equiaxed grain structure with average size of $2.5{\mu}m$. The microstructures of the extruded billet are observed by the use of an electron back-scattering diffraction (EBSD) technique to evaluate of the influence on the grain refinement during extrusion process and re-crystallization mechanism of AZ31 Mg alloy.

• Transactions on Electrical and Electronic Materials
• /
• v.9 no.5
• /
• pp.209-212
• /
• 2008

We developed a simple and effective purification method to obtain high-purity single-walled carbon nanotubes (SWCNTs) with low surface damage. The purification process consists of oxidization at $430^{\circ}C$ for 1 h in a furnace system of air atmosphere and homogenization in dilute hydrochloric acid solution for extremely short time. The role of homogenizer was examined during purification process in terms of purity and quality of purified SWCNTs. High-purity and low surface damage of SWCNT products was obtained using homogenizer which was operated at 8500 rpm for 10 min in the environment of 7 % HCI solution. From XRD spectra, we observed that metal catalysts were thoroughly removed. Raman spectra showed that the intensity values of crystallization ($I_{G}/I_{D}$) of purified SWCNTs were very similar with that of pristine SWCNTs. Moreover, the structure damage of purified SWCNTs was hard to find from electron microscopy. Consequently, homogenizing, which is a quick and simple manner, can be promising method for obtaining final SWCNTs with clearly high purity and crystallinity.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.11
• /
• pp.18-23
• /
• 2019

The oil immersion method can be used to create objective lenses with long working distances without sacrificing the focusing resolution for laser processing. In this study, a space in which air or oil can be filled was formed in the middle of a lens for analyzing the optical properties of a liquid-oil immersion lens. As the refractive media, air and oils of different refractive index values (1.2 and 1.5, respectively) were used. A simulation was conducted in the ZEMAX software environment using the ray-tracing technique, and the performance of the oil immersion lens was verified by determining its image distortion and focal length (FL) in each medium. In the case of air, the calculated FL was 0.813 mm, whereas the imaged FLs were 1.594 mm and 8.126 mm when the refraction indices were 1.2 and 1.5, respectively. The FL of an oil immersion lens could be increased considerably. In terms of image distortion, the oil immersion lens exhibited little distortion at the center in all cases, but different degrees of image distortion were observed at different points away from the center depending on the refraction index degree.

• Journal of Powder Materials
• /
• v.28 no.1
• /
• pp.25-30
• /
• 2021

The surface of silicon dummy wafers is contaminated with metallic impurities owing to the reaction with and adhesion of chemicals during the oxidation process. These metallic impurities negatively affect the device performance, reliability, and yield. To solve this problem, a wafer-cleaning process that removes metallic impurities is essential. RCA (Radio Corporation of America) cleaning is commonly used, but there are problems such as increased surface roughness and formation of metal hydroxides. Herein, we attempt to use a chelating agent (EDTA) to reduce the surface roughness, improve the stability of cleaning solutions, and prevent the re-adsorption of impurities. The bonding between the cleaning solution and metal powder is analyzed by referring to the Pourbaix diagram. The changes in the ionic conductivity, H2O2 decomposition behavior, and degree of dissolution are checked with a conductivity meter, and the changes in the absorbance and particle size before and after the reaction are confirmed by ultraviolet-visible spectroscopy (UV-vis) and dynamic light scattering (DLS) analyses. Thus, the addition of a chelating agent prevents the decomposition of H2O2 and improves the life of the silicon wafer cleaning solution, allowing it to react smoothly with metallic impurities.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.3
• /
• pp.105-109
• /
• 2022

For the realization of higher reliable transition metal dichalcogenide layer, molybdenum disulfide was formed on sapphire substrate by direct current sputtering and subsequent rapid thermal annealing process. Unlike RF sputtered MoS₂ thin films, DC sputtered showed no irregular holes and protrusions after annealing process from scanning electron microscope images. From atomic force microscope results, it was possible to investigate that surface roughness of MoS₂ thin films were more dependent on DC sputtering power then annealing temperature. On the other hand, the Raman scattering spectra showed the dependency of significant E¹_2g and A¹_g peaks on annealing temperatures.