• Proceedings of the KSME Conference
• /
• 2000.11a
• /
• pp.231-237
• /
• 2000

A15052/AFRP laminates were developed principally to obtain a material with good fatigue strength, in which possible cracks would grow very slowly. Weight savings of more than 30% should be attainable in practice. Also, the crack bridging fibers could still was carry a significant part of the load over the crack, thus the COD and stress intensity factor was reduced at the crack tip. A15052/ AFRP laminates consists of three thin sheets of 5052-H34 aluminum alloy and two layers of [0] unidirectional aramid fiber prepreg. The cyclic-bending moment test was investigated based on applying the five kinds of bending moments. The size of the delamination zone produced between 5052-H34 aluminum alloy sheets and fiber-adhesive layers was measured from ultrasonic C-scan pictures taken around the fatigue crack. In addition, the relationship between the cyclic-bending moment and the delamination zone size was studied and the effect of fiber bridging mechanism was also considered.

• Interaction and multiscale mechanics
• /
• v.3 no.2
• /
• pp.173-191
• /
• 2010

Damage detection plays a very important role to the maintenance of bridge structures. Traditional damage detection methods are usually based on structural dynamic properties, which are acquired from pre-installed sensors on the bridge. This is not only time-consuming and costly, but also suffers from poor sensitivity to damage if only natural frequencies and mode shapes are concerned in a noisy environment. Recently, the idea of using the dynamic responses of a passing vehicle shows a convenient and economical way for damage detection of bridge structures. Inspired by this new idea and the well-established tap test in the field of non-destructive testing, this paper proposes a new method for obtaining the damage information through the acceleration of a passing vehicle enhanced by a tapping device. Since no finger-print is required of the intact structure, this method can be easily implemented in practice. The logistics of this method is illustrated by a vehicle-bridge interaction model, along with the sensitivity analysis presented in detail. The validity of the method is proved by some numerical examples, and remarks are given concerning the potential implementation of the method as well as the directions for future research.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1029-1034
• /
• 2004

Recent engineering process requires fast development and manufacturing of the products. This paper mainly discusses the process of rapid product development (RPD) from the reverse engineering to the optimal design. A laser scanning system scans a product and the efficient data processing method reduces the scanned point data. The reduced (scanned) points model is transformed to a finite element model without the construction of a CAD model. Since CAD modeling is a time-consuming work, skipping this step can save much time. This FE model is updated from the result based on the structural characteristics from modal test of the real model. For FE model updating, Response Surface Method is adopted. Finally, the updated FE model is optimized using the reliability-based topology optimization, which is developed recently. All these processes are applied to the design of an upper part model of a cellular phone.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.8
• /
• pp.18-24
• /
• 2011

A new problem happens with the evolution of TSV based 3D IC design. The bonding process takes place which follows with the testing of design for proper connectivity in the absence of TSV redundancy. In order to achieve good yield, the design should be tested with redundancy TSV. This paper presents a wrapper cell design for redundancy TSV interconnect test. The design for test technique, in terms of hardware and software perspectives is described. The wrapper cell with hardware design can use original test patterns. However, software design has less area overhead.

• Journal of the HCI Society of Korea
• /
• v.8 no.1
• /
• pp.19-28
• /
• 2013

As yet the use of 3D scanning technology has been limited to documentation, preservation and monitoring in cultural and natural heritage domain. Appropriate visualization of precise geometric information in scan data can support scientific interpretation of the domain experts. We studied the rendering techniques which visualize the required features from scanned models, and proposed a 3D scan data visualization pipeline, rendering methods, and a classification scheme. As a case study, we analyzed the traditional method in the study of dinosaur tracks and performed the visualization of 3D scanned models. A user test based on the result confirmed an effectiveness of the proposed method. This research showed a practical method in which 3D scanned models can be used to effective interpretation of heritage.

• Journal of radiological science and technology
• /
• v.46 no.5
• /
• pp.401-408
• /
• 2023

Thyroid uptake measurements can be subject to measurement errors due to the scoping and positioning of the thyroid gland. To compensate for these limitations, the clinical utility of the thyroid simultaneous counting method as an alternative to thyroid uptake measurement was analyzed and evaluated experimentally through quantitative analysis of images acquired after thyroid scanning. Experimental data were obtained using a Gamma camera (GE infinia), a thyroid uptake system (KOROID 1), and a thyroid neck phantom. Based on the thyroid uptake rate of 1-5% according to the protocol of thyroid scan test (^99mTcO₄ - , 370 MBq) in normal results, ^99mTcO₄ - was set in the range of 3.7-18.5 MBq (Matrix: 256×256, Scan time: 1 min, collimator: pin hole, phantom-collimator distances: 7 cm). The acquired images were corrected for the attenuation of isotopes due to the set-up time and half-life by applying the Auto Region of interest (ROI) drawing system, and the significance of the experimental results was evaluated by Multiple linear regression analysis (SPSS, ver. 22, IBM). The thyroid uptake rate showed a significant correlation between the dose and the measured counts when using the thyroid uptake system equipment. Meanwhile, the quantitative analysis counts of phantom images using Gamma camera also showed a significant correlation. Thus confirmed that the correlation between these two experiments was statistically significant (P<0.05). The simultaneous counting protocol, which indirectly measures thyroid uptake from thyroid scans, is likely to be clinically relevant if complemented by additional studies with different variables in patients with thyroid disease.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.15 no.2
• /
• pp.21-25
• /
• 2011

Purpose: $^{18}F$-FDG Fusion Whole Body PET scan is performed approximately 1 hour after injecting $^{18}F$-FDG. At this point in the injection procedure, as a tool of the criteria of time input, time of clocks or computers can be used and in the scan procedure, time of workstation can be used. In case that synchronized time input is not done in the injection and scan procedures for PET scan, time error from injection to scan can occur. This time error may affect Standard Uptake Value (SUV) being used as quantitative assessment. Therefore, in this study, we analyzed the change of SUV according to time input difference and necessity of time synchronization. Materials and Methods: The analysis was performed to 30 patients ($54.8{\pm}15.5$ years old) who examined $^{18}F$-FDG Fusion Whole Body PET scan in Department of nuclear medicine, Asan Medical Center from December 2009 to February 2010. To observe the change of SUV according to time input difference, the image was reconstructed and analyzed by artificially changing time difference of 1, 2, 3, 5, 10, 20 min against the same patients based on 60 minutes. Result: SUV of the image that reconstructed the images of 30 patients by giving intervals of 1, 2, 3, 5, 10, 20 min respectively and the image that entered original time was compared and analyzed through paired t-test. Based on 0 minute, mean SUV of aorta was changed by 0.3, 1.1, 1.4, 3.2, 4.7, 12.5% respectively and there was no statistically significant difference in 1, 2 minutes (p>0.05) but there was significant difference in 3, 5, 10, 20 min (p<0.05). The changes of $SUV_{avg}$ of liver were 1.6, 2.5, 3.0, 4.2, 6.6, 12.8% in 1, 2, 3, 5, 10, 20 min respectively and the changes of $SUV_{max}$ of primary lesion were 1.0, 1.5, 2.2, 3.5, 6.6, 12.8% respectively (p<0.05). Conclusion: Errors may occur in the process of measuring or recording variables affecting SUV such as height and weight of patients, $^{18}F$-FDG dose, Emission scan start time etc. and as these errors are more, the accurate assessment of SUV is interfered. Therefore, in order to assess SUV more accurately, it is thought that efforts to minimize these errors should be made. Of these efforts, time synchronization will be a cornerstone for accurate scanning.

• Culinary science and hospitality research
• /
• v.22 no.2
• /
• pp.78-92
• /
• 2016

This study investigated the quality characteristics of white pan bread with banana addition. This analysis was through mixograph and stickiness of dough, fermentation rate, TPA, crumbScan image analysis, color, moisture contents and acceptance test. Mixograph peak time presented 4~5 minutes on every sample. However, CON, B10 and B20 sample presented more than 60%, and B30, B40 presented less than 60% at peak value (%). The result indicated that banana addition increased as the stickiness decreased. The fermentation rate generally increased, but the sample B40 decreased after 75 minutes. The result of crust and inside color, CON was the highest on lightness L value, B40 was the highest on both red a value and yellow b value. The result of pH showed that B40 was the lowest, and more banana addition made pH decreased. Thus, adding banana influences negatively on volume and cost of the product. The image analysis through crumbScan did not show any significant difference on crust thickness and distortion of crumb fineness. On the other hand, CON value was 774.33 that was the lowest, and B40 value was 927.66 which is the highest on the density of crumb fineness. Hardness showed a significant difference; B40 was the lowest, and Control was the highest. Moisture contents generally had a noticeable difference; CON value was the highest, and banana addition increased as the value decreased. At the result of acceptance test, one of the sensory tests, B20 showed the highest grade, and B40 showed the worst. Based on the above results of characteristic difference, banana addition could influence volume of the bread negatively.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.19 no.5
• /
• pp.347-355
• /
• 1999

A feasibility investigation on vibration-based nondestructive evaluation of thermal stress-induced micro-failure in the free edge region of thin composite laminates(1mm thick) has been carried out. The failure occurrence and damage zone, which were predicted by the three-dimensional finite-element thermal stress analysis, were observed using the ultrasonic C-scan and optical microscopy. Analysis of the vibration spectrum measured from the laminate beam specimens by the vibration sweep test exhibited that the obvious decrease in resonancy frequency and some considerable increase in damping factor were associated with the micro-failure formation. The vibration technique utilizing short beam and high resonant frequency was found to be very sensitive to the thermal stress-induced damage in the thin laminates.

• Journal of Welding and Joining
• /
• v.19 no.1
• /
• pp.40-48
• /
• 2001

An ultrasonic test method, as a nondestructive test is applied to ensure the clad interface quality assessment. According to the reference codes and standards, not only korea Industrial Standard(KS) but also American Society for Testing and Materials (ASTM) Standard, ultrasonic examination procedures use the pulse-echo, A-scan, back reflection signal drop method and/or side drilled reference hole used to establish the acceptance criteria of clad material test. But the variety of bonding materials and sizes makes it difficult to produce the reference blocks, or thus the criteria. In order to overcome these practical difficulties, new ultrasonic testing criterion is suggested. In this new method, the theoretical interface reflection signal amplitude level is calculated and suggested as an acceptance criteria with the back reflection signal set to 100% FSH(Full Screen Height) which is based on acoustic impedance mismatch at the clad interface for the explosive clad ultrasonic inspection. Applicability of suggested criterion, for the explosive clad Fe-Naval Brass with different bonding quality is confirmed to the pre-existed KS and ASTM specifications and verified by using SEM (Seanning Electron Microscope) micrograph. The results obtained by the suggested method is more conservative than the results according to the KS B 0234 and ASTM A 578 specifications The suggested method could be applicable to any other combination of explosive clad ultrasonic inspection.