• Journal of Navigation and Port Research
• /
• v.35 no.10
• /
• pp.799-804
• /
• 2011

The hydrodynamic interaction effects between the multi-bodies can not be neglected when vessels are close to each other in congested and confined waters, such as in a harbour or narrow channel. Increase in speed and size of modern vessels make it necessary to consider this interaction effects when designing harbours and navigation channels. In this research, the hydrodynamic interaction effects of the spacing between vessels and water depth along with ship's velocity are summarized and discussed. The goal of this research is to propose a guideline of appropriate speed and distance between passing and moored vessels to avoid the influence of hydrodynamic forces and to navigate safely in confined sea areas.

• Journal of Periodontal and Implant Science
• /
• v.53 no.1
• /
• pp.85-95
• /
• 2023

Purpose: In recent years, guided implant surgery has been widely used for the convenience of patients and surgeons. Further streamlining the surgical procedure would make implant surgery more convenient. Low-speed water-free conditions are often used in guided implant surgery. Therefore, in this study, we attempted to confirm once again whether drilling was safe at a low speed without water. The main purpose of this study was to evaluate whether a simplified drilling protocol that omits some intermediate steps in the drilling process was safe from the viewpoint of heat generation. Methods: D1 density artificial bone blocks were drilled under 50 rpm, 10 N·cm water-free conditions, and the surface temperature was measured using a digital infrared camera. First, drilling was performed with the sequential drilling method, which is the most widely used technique. Second, for each drill diameter, the temperature change was measured while performing simplified drilling with omission of the previous 1, 2, or 3 steps. Results: In sequential drilling, the heat generated during drilling at all diameters was less than the critical temperature of osteonecrosis (47℃) except for the ⌀2 drill. Statistical significance was observed in all groups when comparing sequential and simplified drilling in the ⌀3.2, ⌀3.8, and ⌀4.3 drills (P<0.001). However, in the simplified drilling procedures, the temperature was below the osteonecrosis threshold temperature (47℃) except for the ⌀4.3 drill with the omission of the previous 3 steps (⌀3.0, ⌀3.2, and ⌀3.8). Conclusions: In general, drilling under low-speed, water-free conditions has shown stable results in terms of heat generation. Simplified drilling showed statistically significantly greater heat generation than sequential drilling. However, most of the diameters and omitted steps seem to be clinically acceptable, so it will be useful if an appropriate selection is made according to the patient's clinical condition.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.5
• /
• pp.410-415
• /
• 2004

To ensure a safe operation of the prototype KGT-74 kW small gas turbine, vibrational reliabilities of the compressor 1st, 2nd, and 3rd stages and turbine blades have been estimated and reviewed. FE analyses have been carried out to obtain the natural vibration characteristics of the blades, and impact modal testings have been performed on every each one of the blades to measure their 1st natural frequencies. Then, the Campbell diagram analyses have been carried out to judge the safety of the blades from resonant failures up to 6k harmonics. Results show that the compressor 1st stage blade is exposed to a potential resonant failure with 3k harmonic around a rated speed of 30,000 rpm but that the other compressor 2nd and 3rd stages and turbine blades are safe from resonant failures. Finally, 27,900 rpm is selected as the safe operation limit for the KGT-74 ㎾ gas turbine relative to the blade vibrations.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2003.05a
• /
• pp.297-302
• /
• 2003

To ensure a safe operation of the prototype KGT-74 ㎾ small gas turbine, vibrational reliabilities of the compressor 1st, 2nd. and 3rd stages and turbine blades have been estimated and reviewed. FE analyses have been tarried out to obtain the natural vibration characteristics of the blades, and impact modal testings have been performed on every each one of the blades to measure their 1st natural frequencies. Then, the Campbell diagram analyses have been carried out to Judge the safety of the blades from resonant failures up to 6k harmonics. Results show that the compressor 1st stage blade is exposed to a potential resonant failure with 3k harmonic around a rated speed of 30,000rpm but that the other compressor 2nd and 3rd stages and turbine blades are safe from resonant failures. Finally. 27,900 rpm Is selected as the safe operation limit for the KGT-74 ㎾ gas turbine relative to the blade vibrations.

• 한국방재학회:학술대회논문집
• /
• 2008.02a
• /
• pp.485-488
• /
• 2008

The structure supporting road sign is a road information facility for ensuring the safe transportation and smooth traffic. But, lots of road information facilities were damaged by the typhoon "Maemi" in 2003. Such damaged facilities should be rehabilitated and could increase economic loss by causing traffic accident. Therefore, in this study, behavior that reduce wind load and improve wind resistance of the structure supporting road sign are studied about wind load beyond design specification by abnormal climate as below. The first is wind load reducing technique such that shear key resist wind load that is not greater than design wind speed but in case that it is over the design wind limit, column member is rotated on the inner steel pipe axis by the brittle failure of shear key. The second is the technique such that fail-safe the overturning of road sign panel by equipment installation in the vertical member. The third is the technique of installing stiffening plate inside the vertical member to relieve stress concentration.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.14 no.2
• /
• pp.130-135
• /
• 2014

For the past three decades, ship-to-ship collision accidents have steadily increased on the coast of South Korea by about 20% annually. Marine accidents have become more likely and more devastating in areas with increasing marine traffic and rising numbers of high-speed ships. Over 30% of the marine accidents in South Korea are concentrated in spring, since Korea's coast is often covered in dense fog at this time of the year. Fog is generated when a large temperature range exists within a day, and this daily temperature range has increased due to abnormal weather conditions. This research proposed a system for transmitting a navigator's intention utilizing electronic methods. A navigator's intention was expressed on the electronic navigation chart for easier understanding of the surrounding situation, and the effectiveness of the system was verified through practical tests.

• Journal of Engineering Education Research
• /
• v.13 no.5
• /
• pp.20-24
• /
• 2010

The total number of deaths by traffic accidents is decreasing every year in our country. However, in 2009, children died in traffic accidents at a rate of 2.3 deaths per 100,000 children, which was higher than the average of OECD countries (1.9 deaths per 100,000 children). In particular, traffic accidents are showing rapid increase in school zone during the past 2 years because of problems in the designation and management of school zone. Traffic safety facilities such as road sign, reflector mirror, speed bump have the ultimate limit of vehicle accidents prevention. Thus, in school zone, children safety is still not guaranteed due to illegal parking and the absence of driver's awareness of safety. Therefore, In order to protect children from traffic accidents within school zones, we have realized a safe school zone system, which enables the drivers to better know the intended school zones and creates pedestrian environment through unmanned monitoring camera, using LabVIEW.

• The Journal of Korea Robotics Society
• /
• v.7 no.2
• /
• pp.83-91
• /
• 2012

In this paper, we propose a cable climbing robot which can climb up and down the cables in the bridges. The robot mechanism consists of three parts: a wheel based driving mechanism, adhesion mechanism, and safe landing mechanism. The wheel based driving mechanism is driven by tooth clutches and motors. The adhesion mechanism plays the role of maintaining adhesion force by a combination of pantograph, ball screw, and springs even when the power is lost. The safe landing mechanism is developed for guaranteeing the safety of the robot during operations on cables. It can make the robot fall down with reduced speed by dissipating the gravitational forces. The robot mechanism is designed and manufactured for validating its effectiveness.

• Proceedings of the KSR Conference
• /
• 2010.06a
• /
• pp.1068-1074
• /
• 2010

In high speed railway, event recorder is essential system for analyzing the cause of train accident. It stores train operation sent by train control system in safe memory unit. Crash protected memory, the safe memory unit for event recorder, keeps the stored contents from severe environment. For crash protected memory, we have designed the architecture of concrete enclosure and controller board. Proposed system provides large volume of memory capacity and fault tolerance architecture. For checking the characteristics of proposed crash protected memory specification, the simulation is executed. Simulation results shows the designed crash protected memory meets all requirements.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.406-406
• /
• 2000

In this study, as a part developing an unmanned container terminal (UCT), Ive designed and implemented an Autonomous Ground Vehicle (AGV) that can deliver containers in the port fast and safely as they are scheduled. It is preferable to research the intelligent UCT/AGV for delivering containers all day long without causing any trouble. For the sake of safe and fast AGV driving, we implemented a multiple-sensor system with vision, ultrasonic, and IR sensors and we adapted the hight-speed wireless LAN that satisfies the IEEE 802.11 Standard for hi-directional communication between the main processor in AGV and a host computer. The Pentium-III processor board mounted on the bottom frame in AGV combines and computes the information from sensors and controls the AGV driving. There are also the 80C196KC micro-controllers to control the actuating and steering motors. In addition, a steering function that is defined newly in this paper is heavily concerned in the mechanical design, and it plays an important role when AGV moves along a curve. Experimental results show the fast and safe delivery operations are possible with this UCT/AGV