• 한국주조공학회지
• /
• 제25권4호
• /
• pp.161-167
• /
• 2005

The experiment of hot dip interaction tests was carried out in order to study the formation behavior of interfacial reaction layer between as-received STD61 hot work tool steel and a commercial pure aluminum melt, Al-xwt.%Fe(x=0.2, 0.5, 0.8 and 1.1) alloys melt and Al-xwt.%Si(x=1.0, 4.0, 7.0 and 10.0) alloys melt, respectively. The results show that the reaction layer, over 300 ${\mu}m$ in thickness, is easily formed by the dissolution of silicon from as-received tool steel. When the iron content in the aluminum alloy is higher than 1.1 wt.%, the thickness of reaction layer decreases below 180 ${\mu}m$ by preventing iron dissolution from the tool steel. The silicon dissolved from tool steel acts as a strong promoter on the formation of reaction layer, but the alloyed silicon in molten aluminum alloys acts as an inhibitor on the formation of reaction layer.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1999년도 추계학술대회 논문집 - 한국공작기계학회
• /
• pp.190-196
• /
• 1999

Hot forgeability of STD 61 steel was boronzed in boronizing paste mainly consisted of B4C and Na2B4O7 at various temperatures and times. Microhardness and thickness of boride layers were measured and distributions of B, Si, Cr and V on the cross section of specimen were observed by EPMA line analysis. Microscopic examination and results of EPMA showed that the boride layer consisted of two layers outer layer of FeB and inner layer of Fe2B. Microhardness of these boride layers was in the range of Hv 1800~2300. Thickness of boride layer increased with times and temperatures. Si-rich $\alpha$ layer was formed between boride layer and matrix. Element such as Cr concentration as Cr23(B, C)6 beneath the boride layer.

• 소성∙가공
• /
• 제13권5호
• /
• pp.435-440
• /
• 2004

The temperature in hot forming of metallic materials, such as hot extrusion and hot forging, ranges from $300^{\circ}C$ to $900^{\circ}C$. Correspondingly, the die also exhibits high temperatures close to that of a work piece and its life is limited generally by high temperature fatigue. Thus, the analysis of high temperature fatigue would need the mechanical properties over the wide ranges of temperature. However, very few studies on the high temperature fatigue of brittle materials have been reported. Especially, the study on the fatigue behavior over such transition temperature regime is very rare. In this paper, the stress-strain curves and stress-life curves of a die steel such as STD61 are experimentally obtained. The wide ranges of temperature from $300^{\circ}C$ to $900^{\circ}C$ are considered in experiments and the transition temperature zone is carefully examined.

• Corrosion Science and Technology
• /
• 제9권6호
• /
• pp.289-293
• /
• 2010

To investigate the corrosion behavior of tools steel surface in various coating film, the surface of hard coated Ti-Zr-N film on the tool steel by using magnetron-sputtering methods was researched using various experimental methods. STD 61 steels were manufactured by using vacuum furnace and solutionized for 1hr at $1050^{\circ}C$. Steel surface was coated with Ti-Zr-N film at $150^{\circ}C$ and 100W for 1h by using DC-sputtering equipment. Surface characteristics of Ti-Zr-N film coated specimens were investigated by OM, XRD, FE-SEM and nano-scratch tester. And corrosion behaviors of the coated specimen were investigated by polarization test and electrochemical impedance spectroscopy(EG&G Co, PARSTAT 2273. USA). It was found that Ti-Zr-N film coated sample had a thick coated layer and showed a good wear resistance and corrosion resistance of surface compared with ZrN and TiN coated sample. The corrosion resistance and mechanical property of Ti-Zr-N film coated STD 61 alloy increased as sputtering time increased.

• 대한기계학회논문집A
• /
• 제38권8호
• /
• pp.857-862
• /
• 2014

하드페이싱층과 기저부의 결합부에서 발생하는 잔류 응력/변형률을 감소시키기 위하여 열응력제어층에 대한 연구가 시작되고 있다. 이 연구에서는 3 차원 유한요소해석을 이용하여 Stellite21 초합금으로 하드페이싱된 STD61 열간금형강의 중간층으로 형성된 열응력제어층의 재료조합과 두께를 예측하고자 한다. 열응력제어층은 Stellite21 과 STD61 의 조합으로 생성하였다. 열응력제어층의 두께범위는 0.5-1.5 mm 로 선정하였다. 유한요소해석 결과를 이용하여 열응력제어층을 구성하는 Stellite21과 STD61의 혼합율 및 열응력제어층 두께에 따른 시편 내부 온도/열응력/열변형률분포를 정량적으로 분석하였다. 이 결과로부터 적합한 열응력제어층의 재료혼합비는 Stellite21 50 % 와 STD61 50 % 이며, 적절한 열응력제 어층의 두께는 1.0 mm 임을 알 수 있었다.

• 대한금속재료학회지
• /
• 제50권2호
• /
• pp.176-182
• /
• 2012

The main purpose of this study was to evaluate the endurance against Al alloy melts and wear resistance of an in-situ synthesized titanium matrix composite (TMC) sleeve for aluminum alloy die-casting. The conventional die-casting shot sleeve material was STD61 tool steel. TMCs have great thermal stability, wear and oxidation resistance. The in-situ reaction between Ti and $B_4C$ leads to two kinds of thermodynamically stable reinforcements, such as TiBw and TiCp. To evaluate the feasibility of the application to a TMCs diecasting shot sleeve, the interfacial reaction behavior was examined between Al alloys melts with TMCs and STD61 tool steel. The pin-on-disk type dry sliding wear test was also investigated for TMCs and STD61 tool steel.

• 열처리공학회지
• /
• 제29권6호
• /
• pp.277-283
• /
• 2016

The influences of cooling pressure of quenching process on the mechanical properties such as hardness, impact endurance and anti-thermal fatigue behaviour of STD61 steel were investigated. The specimens were heat-treated using a vacuum furnace in which they were austenitized at $1,030^{\circ}C$ for 1hour under the pressure of $10^{-3}$ torr and cooled with quenching gas of various pressure, i.e. 1, 2 and 6 bar. According to the observation on the specimens prepared with quenching from austenizing temperature, the mechanical properties of the samples with higher quenching pressure were better than those of prepared at lower quenching pressure. The samples prepared with high quenching pressure showed the more homogeneous microstructure with finer carbides. The size of carbides such as VC and (Fe, Cr)C in quenched specimens decreased with increasing gas quenching pressure. It is considered that the rapid cooling with pressure may restrict the formation and growth of carbide.

• 소성∙가공
• /
• 제24권4호
• /
• pp.272-279
• /
• 2015

The characteristics of the laser metal deposition parameters were studied to enhance the deposition efficiency using a diode pumped disk laser. STD61 hot tool steel plate and Fe based AISI M2 alloy were used as a substrate and powder for the laser metal deposition, respectively. Among the laser metal deposition parameters the laser power, track pitch and powder feed rate were used to estimate the deposition efficiency. From the experimental results, the deposition efficiency was shown to be excellent when 1.8kW laser power 500um track pitch and 10g/min of the powder feed rate were used. For this optimal condition the average hardness of the deposition track was approximately 830HV, and this value is 30~50% better than the hardness of the commercially produced tool steel after heat treatment.

• 연구논문집
• /
• 통권33호
• /
• pp.175-182
• /
• 2003

In this study, the wear resistance of the complex powder diffusion treated KS STD 61 has been investigatived. KS STD 61 tool steel was pretreated in quenching and tempering processes to obtain the tempered martensitic microstructure. The samples were packed with complex powder in steel pot($\Phi$90x60mm) and heated in a box furnace. the complex powder diffusion treatment are carried out at $540^{\circ}C$, $520^{\circ}C$, $500^{\circ}C$ for 40min, 1.5hr and 2.5hr. The microstructure, microhardness, wear resistance, and coating layer thickness of the complex powder diffusion treated samples were investigation. The weight loss of as heat treated sample was 0.4mg and that of the complex powder treated at $540^{\circ}C$ for 2.5hr was 0.17mg. These result means that the wear resistance of tool steels can be easily improved by the powder diffusion process at conventional tempering treatment temperature.

• 전기학회논문지
• /
• 제61권4호
• /
• pp.585-589
• /
• 2012

The characteristics of interface layer and the effect of mole fraction of inlet gas mixture($B_2H_6/H_2/N_2/TiCl_4$) on the microstructure of Ti(B,N) films were studied by microwave plasma hot filament CVD process. Ti(B,N) films were deposited on a substrate(STD-61) to develop a high performance of resistance wear coating tool. Ti(B,N) films were obtained at a gas pressure of 1 torr, bias voltage of 300 V and substrate temperature of $480^{\circ}C$ in $B_2H_6/H_2/N_2/TiCl_4$gas system. It was found that TiN, $TiB_2$, TiB and hexagonal boron nitride(h-BN) phases exist in thin layer on the STD-61.