• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제12권12호
• /
• pp.5744-5764
• /
• 2018

In Wireless Sensor Networks (WSNs) for Internet of Things (IoT) environment, fault tolerance is a most fundamental issue due to strict energy constraint of sensor node. In this paper, a robust energy saving data dissemination protocol for IoT-WSNs is proposed. Minimized energy consumption and dissemination delay time based on signal strength play an important role in our scheme. The representative dissemination protocol SPIN (Sensor Protocols for Information via Negotiation) overcomes overlapped data problem of the classical Flooding scheme. However, SPIN never considers distance between nodes, thus the issue of dissemination energy consumption is becoming more important problem. In order to minimize the energy consumption, the shortest path between sensors should be considered to disseminate the data through the entire IoT-WSNs. SPMS (Shortest Path Mined SPIN) scheme creates routing tables using Bellman Ford method and forwards data through a multi-hop manner to optimize power consumption and delay time. Due to these properties, it is very hard to avoid heavy traffic when routing information is updated. Additionally, a node failure of SPMS would be caused by frequently using some sensors on the shortest path, thus network lifetime might be shortened quickly. In contrast, our scheme is resilient to these failures because it employs energy aware concept. The dissemination delay time of the proposed protocol without a routing table is similar to that of shortest path-based SPMS. In addition, our protocol does not require routing table, which needs a lot of control packets, thus it prevents excessive control message generation. Finally, the proposed scheme outperforms previous schemes in terms of data transmission success ratio, therefore our protocol could be appropriate for IoT-WSNs environment.

• 한국해양바이오학회지
• /
• 제9권1호
• /
• pp.14-21
• /
• 2017

The purpose of this study was to inhibit biofouling on a selectively permeable membrane (SPM) and increase biomass productivity in marine photobioreactors (PBRs) for microalgal cultivation by chemical treatment. Surfaces of a SPM, composed of polyethylene terephthalate (PET), was sulfonated to decrease hydrophobicity through attaching negatively charged sulfonic groups. Reaction time of sulfonation was varied from 0 min to 60 min. As the reaction time increased, the water contact angle value of SPM surface was decreased from $75.5^{\circ}$ to $44.5^{\circ}$, indicating decrease of surface hydrophobicity. Furthermore, the water permeability of sulfonated SPM was increased from $5.42mL/m^2/s$ to $10.58mL/m^2/s$, which reflects higher nutrients transfer rates through the membranes, due to decreased hydrophobicity. When cultivating Tetraselmis sp. using 100-mL floating PBRs with sulfonated SPMs, biomass productivity was improved by 34% compared with the control group (non-reacted SPMs). In addition, scanning electron microscopic observation of SPMs used for cultivation clearly revealed lower degree of cell attachment on the sulfonated SPMs. These results suggest that sulfornation of a PET SPM could improve microalgal biomass productivity by increasing nutrients transfer rates and inhibiting biofouling by algal cells.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2001년도 Proceedings of 6th International Joint Symposium on Microeletronics and Packaging
• /
• pp.9-25
• /
• 2001

Fairchild has been developing a new class IPM called SPM consisting of dramatic Packaging technology to achieve the lowest cost rind better performance for low power home appliances and industrial AC drive applications. The first Fairchild SPM development with IGBT 600V/15A for washing machine application started in 1999 and was completed successfully. Fairchild SPMs are going to be the best solution for low power inverter-driven AC drive system after 2001. The new SPM Packages like SPM ∥ and SPIM for the next generation IPM with the highest competitiveness (cost & performance) shall be continuouslly developed.

• 한국표면공학회지
• /
• 제29권5호
• /
• pp.314-324
• /
• 1996

Scanning probe microscopes (SPMs) such as the scanning tunneling microscope (STM) and the atomic force microscope (AFM) were used for surface modification tools at the nanometer scale. Material surfaces, i. e., titanium, hydrogen-terminated silicon and trimethylsilyl organosilane monolayer on silicon, were locally oxidized with the best lateral spatial resolution of 20nm. The principle behind this proximal probe oxidation method is scanning probe anodization, that is, the SPM tip-sample junction connected through a water column acting as a minute electrochemical cell. An SPM-nanolithogrphy process was demonstrated using the organosilane monolayer as a resist. Area-selective chemical modifications, i. e., etching, electroless plating with gold, monolayer deposition and immobilization of latex nanoparticles; were achieved in nano-scale resolution. The area-selectivity was based on the differences in chemical properties between the SPM-modified and unmodified regions.

• 한국자동차공학회논문집
• /
• 제21권3호
• /
• pp.165-173
• /
• 2013

Core loss has a major effect on heat generation in synchronous motors with surface-mounted permanent magnets (SPMs). It is essential to perform heat transfer analysis considering core loss in SPM because core loss is seriously affected by torque and speed of motors. In the present study, mechanical loss, core loss and coil loss are evaluated by measuring input and output energies under various driving conditions. For a better understanding heat transfer paths in synchronous motors, we developed a lumped thermal system analysis model. Subsequently, heat transfer analysis has been performed based on acquired energy loss, temperature data and thermal resistance with three types of SPM. It is shown that the torque constants decrease by Max. 10% as speed increase. At the rated torque, the core loss is Max. 10.9 times greater than the coil loss and the hysteresis loss of magnets is dominant in total loss.

• 인터넷정보학회논문지
• /
• 제10권1호
• /
• pp.43-50
• /
• 2009

잘 알려진 무선 센서 네트워크의 프로액티브 프로토콜인 Flooding과 SPIN은 싱크 노드의 요청 없이 감지한 데이터를 즉각적으로 전송한다. 그러나 이러한 전송방법은 그 데이터가 필요하지 않는 노드들에게까지 전송하기에 에너지 효율성 측면에서 비효율적이다. 본 논문에서는 이러한 단점을 극복하기 위해서 전체 노드 대신에 적절한 일부 노드들에게만 전송할 수 있는 세미프로액티브 프로토콜을 제안한다. 따라서 만일 싱크노드와 같은 어떠한 노드가 감지한 데이터를 필요로 할 경우 미리 설정한 몇 홉 이내에 그 데이터를 쉽게 얻을 수 있다. 시뮬레이션 결과는 잘 알려진 SPIN과 비교하여 노드의 에너지 효율성이 약 83%까지 높다는 것을 보여주었다.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• 제44권5호
• /
• pp.220-224
• /
• 2018

Objectives: The aim of this study was to determine the incidence and characteristics of second primary malignancy (SPM) in patients with head and neck squamous cell carcinoma treated at a tertiary care hospital. Materials and Methods: We retrospectively reviewed the medical records of 221 patients who underwent surgery with or without adjuvant treatment for head and neck cancer from 2000 to 2002. Data of age, sex, risk factors, sites of primary and SPM, TNM stage of primary tumor, incidence of SPM, and survival were collected from medical charts. Results: Eighteen patients developed SPM during a median follow-up of 67 months, with an overall incidence of 8.14%. In addition, 77.7% of SPMs occurred in the oral cavity, followed by 11% in the lungs. The 5-year overall survival after the diagnosis of SPM in the head or neck was 70%, compared to 30% for SPM in other body regions. Conclusion: Considering a high incidence of SPM, i.e., 8.14%, in a mean follow-up period of 67 months suggests the need for long-term follow-up. Since treatment of SPM has shown an acceptable survival rate, early detection and curative therapy should be emphasized.

• 대한기계학회논문집
• /
• 제2권3호
• /
• pp.53-61
• /
• 1978

This study has been concentrated on the relations between the crack growth rate and the stress intensity factor, the fatigue limit and finally on the condition of the crack propagation along the laminated cross section of the laminated steel under the repeated plane bending through tests. The following results are obtained. 1. The fatigue limit of the laminated steel is higher than the single steel 2. The realtion between the fatigue crack growth rate, dL/dN and Stress intensity factor are ; dL/dN = 2.14 * 10$^{-11}$ $K^{2.95}$ for SUP 9 dL/dN = 1.70 * 10$^{-11}$ $K^{2.95}$ for SMS dL/dN = 9.77 * 10$^{-11}$ $K^{2.95}$ for SPMS dL/dN = 3.57 * 10$^{-8}$ $K^{1.53}$ for SPMM dL/dN = 5.5O * 10$^{-8}$ $K^{1.53}$ for MLD 3. The crack propagation of the laminated steel also tends to be completed through 3 steps; The first step proceeds swiftly, in a second slowly for a long time and last very rapidly for a short moments.

• The Korean Journal of Physiology and Pharmacology
• /
• 제24권2호
• /
• pp.165-171
• /
• 2020

Ischemic and traumatic brain injuries are the major acute central nervous system disorders that need to be adequately diagnosed and treated. To find biomarkers for these acute brain injuries, plasma levels of some specialized pro-resolving mediators (SPMs, i.e., lipoxin A4 [LXA4], resolvin [Rv] E1, RvE2, RvD1 and RvD2), CD59 and interleukin (IL)-6 were measured at 0, 6, 24, 72, and 168 h after global cerebral ischemic (GCI) and traumatic brain injuries (TBI) in rats. Plasma LXA4 levels tended to increase at 24 and 72 h after GCI. Plasma RvE1, RvE2, RvD1, and RvD2 levels showed a biphasic response to GCI; a significant decrease at 6 h with a return to the levels of the sham group at 24 h, and again a decrease at 72 h. Plasma CD59 levels increased at 6 and 24 h post-GCI, and returned to basal levels at 72 h post-GCI. For TBI, plasma LXA4 levels tended to decrease, while RvE1, RvE2, RvD1, and RvD2 showed barely significant changes. Plasma IL-6 levels were significantly increased after GCI and TBI, but with different time courses. These results show that plasma LXA4, RvE1, RvE2, RvD1, RvD2, and CD59 levels display differential responses to GCI and TBI, and need to be evaluated for their usefulness as biomarkers.

• 한국정보통신학회논문지
• /
• 제18권9호
• /
• pp.2079-2086
• /
• 2014

조선소에서 생산관리는 생산성 향상과 가장 밀접한 업무 중의 하나이다. 현업 생산관리자와 공정계획 엔지니어들은 상호 간의 정보 공유 미흡으로 인해 공정계획 및 공정관리에 대한 충분한 생산정보를 얻지 못한다. 본 연구에서는 생산계획과 공정관리의 요구사항 분석을 통하여 생산공정모니터링 시스템에 대한 주요 이슈를 도출하고, 콤포넌트 기반 설계 기법을 활용하여 시스템 아키텍처를 수립하였다. 제안한 시스템의 주요 기능은 블록 조립에서 안벽의장 단계까지 수립하여 생산공정현황을 시각적으로 보여 줄 뿐 아니라 공정정보 공유를 극대화하는 것이다. 본 시스템은 생산관리자에게 신뢰성 있고 정확한 생산 정보를 제시간에 제공할 수 있을 것으로 기대된다.