• Journal of the Korean Vacuum Society
• /
• v.7 no.1
• /
• pp.29-34
• /
• 1998

The solid-phase crystallization (SPC) of plasma-enhanced chemical vapor depsoited (PECVD) amorphous silicon (a-Si) films ha s been investigated by x-ray diffraction (XRD). The a-Si films were prepared on Si (100) wafers using $SiH_4$ gas and without $H_2$ dilution at the substrate temperatures between $120^{\circ}C$ and $380^{\circ}C$, and than annealed at $600^{\circ}C$ for crystallization. The annealed samples exhibited (111), (220), and (311) XRD peaks with preferential orientation of (111). The XRD peak intensities increased as the substrate temperature decreased, and the $H_2$dilution suppressed the solid-phase crystallization. The average grain size estimated by XRD analysis for the (111) texture has increased from about 10 nm to about 30 nm, as the substrate temperature decreased. The deposition rate also increased with the decreasing substrate temperature and the grain size was closely dependent on the deposition rate of the films. The grain size enhancement was attributed to an increase of the structural disorder of the Si network.

• Journal of Magnetics
• /
• v.17 no.4
• /
• pp.265-270
• /
• 2012

We report improved low-field magnetoresistance (LFMR) effects of the $La_{0.7}Sr_{0.3}Mn_{1+d}O_3-Mn_3O_4$ composite films with the nominal composition of $La_{0.7}Sr_{0.3}MnO_3$(LSMO)-50 mol% $Mn_3O_4$. The composite films were fabricated by ex-situ solid phase crystallization (SPC) of amorphous films at the annealing temperature region of $900-1100^{\circ}C$ for 2 h in a pure oxygen atmosphere. The amorphous films were deposited on polycrystalline $BaZrO_3$ (poly-BZO) substrates by dc-magnetron sputtering at room temperature. The Curie temperatures ($T_C$) of all composite films were insignificantly altered in the range of 368-372 K. The highest LFMR value of 1.29 % in 0.5 kOe with the maximum dMR/dH value of $37.4%kOe^{-1}$ at 300 K was obtained from 900 nm-thick composite film annealed at $1100^{\circ}C$. The improved LFMR properties of the composite films are attributed to effective spin-dependent scattering at the $La_{0.7}Sr_{0.3}Mn_{1+d}O_3$ grain boundaries sharpened by adjacent chemically compatible $Mn_3O_4$ grains.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.1
• /
• pp.26-35
• /
• 2024

Aluminum-induced crystallization (AIC) as a route to reduce the fabrication cost and to obtain polycrystalline Si (p-Si) thin-film of large grain size is a promising alternative of single-crystalline (s-Si) substrate or p-Si thin-film obtained by conventional methods such as solid phase crystallization (SPC) and laser-induced crystallization (LIC). As the AIC process occurs at the interface between a-Si and Al thin-films, there are various process and interface parameters. Also, it directly means that there is a certain parametric window to obtain p-Si of large grain size having uniform crystal orientation. In this article, we investigate the effect of the various process and interface parameters to obtain p-Si of large grain size and uniform crystal orientation from the literature review. We also suggest the potential use of the p-Si as a virtual substrate for the growth of various compound semiconductors in a form of low-dimension as well as thin-film as a way for their monolithic integration on Si.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.80-81
• /
• 2008

Schottky barrier thin film transistors (SB-TFT) on polycrystalline silicon(poly-Si) are fabricated by platinum silicided source/drain for p-type SB-TFT. High quality poly-Si film were obtained by crystallizing the amorphous Si film with excimer laser annealing (ELA) or solid phase crystallization (SPC) method. The fabricated poly-Si SB-TFTs showed low leakage current level and a large on/off current ratio larger than $10^5$. Significant improvement of electrical characteristics were obtained by the additional forming gas annealing in 2% $H_2/N_2$ ambient, which is attributed to the termination of dangling bond at the poly-Si grain boundaries as well as the reduction of interface trap states at gate oxide/poly-Si channel.

• Transactions of the Korean hydrogen and new energy society
• /
• v.21 no.5
• /
• pp.412-418
• /
• 2010

Steam reforming of n-hexadecane, a major component of diesel over Ni-based hydrotalcite-like catalyst was carried out at $900^{\circ}C$ at atmospheric pressure with space velocity of $10,000h^{-1}$ and feed molar ratio of steam/carbon=3.0. Ni-based hydrotalcite catalyst was prepared by a solid phase crystallization (spc) method and characterized by $N_2$-physisorption, CO chemisorption, TPR., XRD, and TEM techniques. It was found that spc Ni/MgAl catalyst showed higher catalytic stability and inhibition of carbon formation than Ni/$\gamma-Al_2O_3$ catalyst under the tested conditions. The results suggest that the modified spc-Ni/MgAl catalyst after optimization may be applied for the SR reaction of diesel.

• Journal of the Korean Vacuum Society
• /
• v.12 no.2
• /
• pp.130-135
• /
• 2003

Polycrystalline silicon thin films have been used for low cost thin film device application. However, it was very difficult to fabricate high performance poly-Si at a temperature lower than $600^{\circ}C$ for glass substrate because the crystallization process technologies like conventional solid phase crystallization (SPC) require the number of high temperature (600-$1000^{\circ}C$) process. The objective of this paper is to grow poly-Si on flexible substrate using a rapid thermal crystallization (RTC) of amorphous silicon (a-Si) layer and make the high temperature process possible on molybdenum substrate. For the high temperature poly-Si growth, we deposited the a-Si film on the molybdenum sheet having a thickness of 150 $\mu\textrm{m}$ as flexible and low cost substrate. For crystallization, the heat treatment was performed in a RTA system. The experimental results show the grain size larger than 0.5 $\mu\textrm{m}$ and conductivity of $10^{-5}$ S/cm. The a-Si was crystallized at $1050^{\circ}C$ within 3min and improved crystal volume fraction of 92 % by RTA. We have successfully achieved a field effect mobility over 67 $\textrm{cm}^2$/Vs.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08b
• /
• pp.1781-1784
• /
• 2007

The increase of repetition rate, the dithering of laser optics, and the extension of pulse duration time are major approaches in improving the picture quality of AMOLEDs fabricated by excimer laser crystallization (ELC). Advanced solid phase crystallization (ASPC) has been developed to improve the uniformity and the process cost. Even though the mobility of ASPC-TFT is lower than that of ELC-TFT, it is high enough to drive AMOLED pixels.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.313-313
• /
• 2013

For high-performance TFT (Thin film transistor), poly-crystalline semiconductor thin film with low resistivity and high hall carrier mobility is necessary. But, conventional SPC (Solid phase crystallization) process has disadvantages in fabrication such as long annealing time in high temperature or using very expensive Excimer laser. On the contrary, MIC (Metal-induced crystallization) process enables semiconductor thin film crystallization at lower temperature in short annealing time. But, it has been known that the poly-crystalline semiconductor thin film fabricated by MIC methods, has low hall mobility due to the residual metals after crystallization process. In this study, Ni metal was shallow implanted using PIII&D (Plasma Immersion Ion Implantation & Deposition) technique instead of depositing Ni layer to reduce the Ni contamination after annealing. In addition, the effect of external magnetic field during annealing was studied to enhance the amorphous silicon thin film crystallization process. Various thin film analytical techniques such as XRD (X-Ray Diffraction), Raman spectroscopy, and XPS (X-ray Photoelectron Spectroscopy), Hall mobility measurement system were used to investigate the structure and composition of silicon thin film samples.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 1999.05a
• /
• pp.403-406
• /
• 1999

The influence of temperature variation (25～125$^{\circ}C$) on poly-Si thin-film transistors (TFT's) was investigated by examining the electrical properties change of poly-Si films formed by solid phase crystallization (SPC). The n-channel poly-Si TFT's fabricated by SPC with channel length of 1.5 and loon ,respectively, exhibit good characteristics with a high ${\mu}$$\sub$FE/ ($\geq$82 and $\geq$60$\textrm{cm}^2$/V-s in 1.5 and 10$\mu\textrm{m}$, respectively), low V$\sub$t/, ($\leq$1.52 and $\leq$ 2.75V in 1.5 and 10$\mu\textrm{m}$, respectively), low S$\sub$t/, and good ON-OFF characteristics in spite of temperature variation. Thus, poly-Si films formed by SPC can be applied for the application to poly-Si TFT liquid crystal display with peripheral integrated circuits.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.1050-1053
• /
• 2002

In this paper, Amorphous silicon on glass substrate was recrystallized to poly-crystalline silicon by solid phase crystallization (SPC) technology. The active region of thin film transistor (TFT) was fabricated by amorphous silicon. The output and transfer characteristics of thin film transistor with lightly doped drain (LDD) structure was measured and analyzed. As a results, analyzed TFTs reliability with LDD's length by various kinds argument such as sub-threshold swing coefficient, mobility and threshold voltages were evaluated. Stress effects in TFT were able to improve to the characteristics of turn-on current and hot carrier effects by LDD's length variations.