• Korean Journal of Hydrosciences
• /
• v.1
• /
• pp.61-71
• /
• 1990

The characteristics of radial thickness of ice jam at the center part of channel bends were analyzed briefly in this paper. Jam thickness in channel bends increases both toward the inner bank, and dowmstream. For this study, slope at the jam's underside was assumed to be liner with similarity of radial slope of bed in alluvial bends. Radial slope at the jam's underside in floating ice elements was estimated using the force equilibrium theory in the radial direction. The eqution which can be estimated the radial slope of ice jam was suggested using Falcon and Kennedy's bed layer theory. Experimental data, which were measured at the center part of cross-section in a single 180-degree bend, were compared to the calculated values using the suggested equtions. The result shows that the calcultated values were smaller than the measured ones. Ot is considered that the estimated value of shear stress in the radial direction may be smaller than the actual and two-layer model may be not suibable for alluvial bend flow.

• The Journal of Engineering Geology
• /
• v.32 no.1
• /
• pp.85-99
• /
• 2022

Rock discontinuities, as weak interfaces in rock, control mechanical properties of rock mass. Presence of discontinuities complicates the engineering properties of rock, which is the root of anisotropy and heterogeneity that have nonnegligible influences on the rock engineering. Morphological characteristics of discontinuities in natural rock are an important factor influencing the mechanical properties, particularly roughness, of discontinuities. Therefore, the accurate measurement and characterization of morphologies of discontinuities are preconditions for studying mechanical properties of discontinuities. Taking discontinuities in red sandstone as research objects, the research obtained three-dimensional (3D) morphologies of discontinuities in natural rock by carrying out 3D morphological scanning tests. The waviness and roughness were separated from 3D morphologies of rock discontinuities through wavelet transform. In addition, the calculation method for the overall slope root mean square (RMS) as well as slope RMSs of waviness and roughness of 3D morphologies of discontinuities considering the shear direction was proposed. The research finally determined an evaluation method for 3D morphologies of discontinuities by quantitatively characterizing 3D morphologies with the mean value of the three slope RMSs.

• Geomechanics and Engineering
• /
• v.31 no.4
• /
• pp.375-384
• /
• 2022

The variation of the undrained shear strength (c_u) is an important consideration for assessing slope stability in engineering practice. Previous studies focused on the three-dimensional (3D) stability of slopes in normally consolidated clays generally assume the undrained shear strength increases linearly with depth but does not vary in the horizontal direction. To assess the 3D stability of slopes with spatially varying undrained shear strength, the kinematic approach of limit analysis was adopted to obtain the upper bound solution to the stability number based on a modified failure mechanism. Three types failure mechanism: the toe failure, face failure and below-toe failure were considered. A serious of charts was then presented to illustrate the effect of key parameters on the slope stability and failure geometry. It was found that the stability and failure geometry of slopes are significantly influenced by the gradient of c_u in the depth direction. The influence of c_u profile inclination on the slope stability was found to be pronounced when the increasing gradient of c_u in the depth direction is large. Slopes with larger width-to-height ratio B/H are more sensitive to the variation of c_u profile inclination.

• Journal of Ocean Engineering and Technology
• /
• v.10 no.3
• /
• pp.34-43
• /
• 1996

In this study basic equations of fiber orientations is cimpared with experimental results. It is found that fiber orientations of short fiber reinforced polymeric composite under compression molding are governed by slope of flow speed in x-y direction. Fiber orientation angle of mold is also found to increase with closure speed and the compression ratio. At the middle of the mold, the slope of flow speed is larger in x-direction than in y-direction. At the wall of the mold, the shope of flow speed in y-direction occurs due to the effect of friction, hence affects the fiber orientation. The effect of partial flow, which incurs y-direction orientation causes to increase the fiber orientation angle at the fore part of the flow.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.31 no.6_1
• /
• pp.431-437
• /
• 2013

Landslides are caused by earthquakes or heavy rains. Recently the incidence of landslides has been increased. However, it is impossible to predict the occurrence of landslide exactly. The purpose of this research is that subdivide the classes of elements in the landslide management system by using spatial analysis technique and AHP method. The existing landslide management system is only comprised of weighted value the slope elements without weighted value about the slop direction elements. For the accuracy improvement in landslide occurrence point, weighted value about the slope direction should be considered. This research is focused on segmentation in slope direction three categories. If the direction of landslide does not affect the structure, I do not think the subject is worth considerating. Based on these results will discuss the improvements in Landslides management systems. Analysis results, segmentation on the slope and the slope direction are needed. Segmented categories about topography elements will be increase the accuracy of landslides management system. Also, since topography of the elements is only considered, segmentation of different elements is needed.

• Economic and Environmental Geology
• /
• v.33 no.1
• /
• pp.51-59
• /
• 2000

As a part of natural hazard assessment, regional slope stability analysis was conducted using Geoscientific Information System (GIS) in the northern area of Chungju Lake. Selected factors which affect the slope stability in the study area were lithology, soil, density of lineament, groundwater level, dip of slope, aspect of slope, and geological engineering properties. Geological structural domains were determined by collected data of joint orientation from about 200 sites in order to produce a slope instability map. Potential type of failure and its direction could be expected through the domains. And a slope instability map was produced, comparing the representative orientations of the domains with the orientations of the slopes which were made through TIN module in ARC/INFO. Under the consideration of environmental geological characteristics of the study area, rating and weighting of each factor of slope stability analysis were decided and spatial analysis of regional slope stability was couducted through overlaying technique of GIS. The result of areal distribution of slope stability showed that the most unstable area was the area between Mt. Pudae and Mt. Jubong, and the northern area of the railway station, Samtan.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.06a
• /
• pp.45-52
• /
• 2003

Construction and extension of road by industrialization are increasing. According to this, construction of large cutting slope is increasing. Therefore, many methods for slope stability by this are applied. Failure happens according to dip and dip direction of slope. It is actuality that is connoting unstable element. This slope include coaly shale. Stability of slope failure this study takes place by road extension running examination for stability property calculate. Use this and examined stability about stereographic projection and wedge failure. Apply suitable reinforcement countermeasure about unstable cutting slope and analyzed stability. Wish to consider effective and robust processing plan of great principle earth and sand side securing stability. Hereafter with these data, is going to utilize in reinforcement and failure prevention.

• The Journal of Engineering Geology
• /
• v.13 no.2
• /
• pp.157-170
• /
• 2003

This study is performed to investigate the cause of slope failure and to suggest suitable stabilization methods for the failed rock slopes. The slope which is located along the national highway between Maesan and Kakok in Dangjin-gun failed during the construction of roads. Site investigation, drilling program, field measurements, rainfall records, and stability analyses are used to investigate the cause of the slope failure. The problem determining the cut-slope angle based on the existing design manual for the construction of roads is reviewed based on the case history given in this paper. If weakness layer and geological structures such as folds and faults are developed in a slope, slope failure is possible even though the direction of slope and the direction of discontinuities depart more than $30^{\circ}$.

• Economic and Environmental Geology
• /
• v.33 no.1
• /
• pp.77-88
• /
• 2000

The goal of this study is to assess the spatial distribution of natural slopes and cutting slopes under would-be development. For this goal, a quantitative slope stability analysis method using GIS integrated with a computer program was developed. Through field investigations, the discontinuity parameters were collected such as orientation of discontinuity, persistence, spacing, JRC, JCS, and water depth. The distributions were interpolated from the ordinary kriging method in ARC/INFO GIS after variogram analysis. The layers showing all parameters needed for limit equilibrium analysis were constructed. The final layer using GIS works composed of 162,352 polygons, that is, unit slopes. The rock slope stability analysis program was coded by C++ language. This program can calculate geometrical vectors related to rock block failures using input orientation data and direction and dimension of strength to occur failure. Also, this can calculate shear strength of joints through empirical equations and quantitative factors of safety. This methodology was applied to the study area which is located in Jaecheon city and Danyang-gun of the northeastern Keumsu is about 135$km^2$. As a result, the study area was entirely stable but unstable, that is, factor of safety less than 1.0dominantly at the slopes near Keumsil, Daejangri, Keumsungmyun and Sojugol, Mt. Dongsan, Juksongmyun by the natural slope stability analysis. Assuming the cutting slope showing the same direction immediate, and quantitative analysis of factors of safety for a regional area could be conducted through GIS integrated with a computer program of limit equilibrium.

• Proceedings of the KSRS Conference
• /
• 2002.10a
• /
• pp.615-620
• /
• 2002

Probability distribution of the sea surface slope is estimated using sun glitter images derived from visible radiometer on Geostationary Meteorological Satellite (GMS) and surface vector winds observed by spaceborne scatterometers. The brightness of the visible images is converted to the probability of wave surfaces which reflect the sunlight toward GMS in grids of 0.25 deg $\times$ 0.25 deg. Slope and azimuth angle required for the reflection of the sun's ray toward GMS are calculated for each grid from the geometry of GMS observation and location of the sun. The GMS images are then collocated with surface wind data observed by three scatterometers. Using the collocated data set of about 30 million points obtained in a period of 4 years from 1995 to 1999, probability distribution function of the surface slope is estimated as a function of wind speed and azimuth angle relative to the wind direction. Results are compared with those of Cox and Munk (1954a, b). Surface slope estimated by the present method shows narrower distribution and much less directivity relative to the wind direction than that reported by Cox and Munk. It is expected that their data were obtained under conditions of growing wind waves. In general, wind waves are not always developing, and slope distribution might differ from the results of Cox and Munk. Most of our data are obtained in the subtropical seas under clear-sky conditions. This difference of the conditions may be the reason for the difference of slope distribution.