The Journal of Korean Institute of Communications and Information Sciences
/
v.30
no.2C
/
pp.25-30
/
2005
Turbo code is popularly used for the reliable communication in the presence of burst errors. Even if it shows good error performance near to the Shannon limits, it requires a large amount of memories and exhibits long latency. This paper proposes an architecture for the low power implementation of the Turbo decoder adopting the Max-Log-Map algorithm. In the proposed design, two SISO decoders are designed to operate in parallel, and a novel interleaver is designed to prevent the collision of memory accesses by two SISO decoders. Experimental results show that power consumption has been reduced by about 40% in the proposed decoder compared to previous Turbo decoders. The area overhead due to the additional interleaver controller is negligible.
JSTS:Journal of Semiconductor Technology and Science
/
v.14
no.4
/
pp.407-418
/
2014
As the high-throughput requirement in the next generation communication system increases, it becomes essential to implement high-throughput SISO (Soft-Input Soft-Output) decoder with minimal hardware resources. In this paper, we present the comparison results between cascaded radix-4 ACS (Add-Compare-Select) and LUT (Look-Up Table)-based radix-4 ACS in terms of delay, area, and power consumption. The hardware overhead incurred from the retiming technique used for high speed radix-4 ACS operation is also analyzed. According to the various analysis results, high-throughput radix-4 SISO decoding architecture based on simple path metric recovery circuit is proposed to minimize the hardware resources. The proposed architecture is implemented in 65 nm CMOS process and memory requirement and power consumption can be reduced up to 78% and 32%, respectively, while achieving high-throughput requirement.
This paper presents generalization and application for the conventional SISO decoding algorithm of Block Turbo Codes. R. M. Pyndiah suggested an iterative SISO decoding algorithm for Product Codes, two-dimensionally combined linear block codes, on AWGN channel. It wascalled Block Turbo Codes. Based on decision of Chase algorithm which is SIHO decoding method, SISO decoder for BTC computes soft decision information and transfers the information to next decoder for iterative decoding. Block Turbo Codes show Shannon limit approaching performance with a little iteration at high code rate on AWGN channel. In this paper we generalize the conventional decoding algorithm of Block Turbo Codes, under BPSK modulation and AWGN channel transmission assumption, to the LLR value based algorithm and suggest an application example such as concatenated structure of LDPC codes and Block Turbo Codes.
The Journal of Korea Institute of Information, Electronics, and Communication Technology
/
v.5
no.3
/
pp.169-173
/
2012
This paper investigates the performance of Turbo equalization in wireless multipath channels. Turbo equalization mainly consists of a SISO(soft-in soft-out) equalizer and a SISO decoder. Iterative channel estimators can improve the accuracy of channel estimates by soft information fed back from the SISO decoder. Comparing iterative channel estimators with LMS(least mean square) and RLS(recursive least squares) algorithms, which are the most common algorithms to estimate and track a time-varying channel impulse response, the iterative channel estimator with RLS converges more faster than the one with LMS. However, the difference of BER(bit error rate) performances gradually decreases as the number of iterations for Turbo equalization increases.
The Journal of Korean Institute of Communications and Information Sciences
/
v.28
no.3C
/
pp.215-223
/
2003
Turbo codes are selected as FEC(Forward error correction) codes with convolution code in 3GFP(3rd generation partnership project) and 3GPP2 standard of IMT2000. Especially, l/3 turbo code with K=4 is employed for 3GPP standard. In this paper, we proposed a hardware structure of a turbo decoder and denveloped the decoder for 3GPP standard turbo code. For its efficient operation, we design a SOVA decoder by employing a register exchange decoding block and new path metric normalization block as a SISO constituent decoder. In addition, we estimate its performance under MATLAB 6.0 and designed the turbo decoder including control block, input control buffer, SOVA constituent decoder with VHDL. Finally, we synthesized the developed turbo decoder under Synopsys FPGA Express and verified it with ALTERA EPF200SRC240-3 FPGA device.
In this paper, a turbo equalizer is proposed for the digital video broadcasting for terrestrial - 2nd generation (DVB-T2) system. The proposed turbo equalizer is consisted with the maximum a posteriori (MAP) and low density parity check (LDPC) decoder. The channel information for the soft-input-soft-output (SISO) MAP equalizer is based on the least square (LS) channel estimator. The performance is analyzed through computer simulations in terms of the iteration number.
Turbo codes are extensively used in current communications standards and have a promising outlook for future generations. The advantages of software defined radio, especially dynamic reconfiguration, make it very attractive in this multi-standard scenario. However, the complex and power consuming implementation of the maximum a posteriori (MAP) algorithm, employed by turbo decoders, sets hurdles to this goal. This work introduces an ASIP architecture for the MAP algorithm, based on a dual-clustered VLIW processor. It displays the good performance of application specific designs along with the versatility of processors, which makes it compliant with leading edge standards. The machine deals with multi-operand instructions in an innovative way, the fetching and assertion of data is serialized and the addressing is automatized and transparent for the programmer. The performance-area trade-off of the proposed architecture achieves a throughput of 8 cycles per symbol with very low power dissipation.
The Journal of Korean Institute of Communications and Information Sciences
/
v.34
no.2C
/
pp.175-180
/
2009
When we apply the LDPC code for high density optical storage channel, it is necessary to make an algorithm that the modulation code decoder must feed the LDPC decoder soft-valued information because LDPC decoder exploits soft values using the soft input. Therefore, we propose the soft-input soft-output run-length limited 17PP decoding algorithm and compare performance of LDPC codes. Consequently, we found that the proposed soft-input soft-output decoding algorithm using 17PP is 0.8dB better than the soft-input soft-output decoding algorithm using (1, 7) RLL.
The Journal of Korean Institute of Communications and Information Sciences
/
v.38A
no.10
/
pp.850-857
/
2013
Turbo equalizer system is a method which can improve performance through a combination of the equalizer and decoder. The turbo equalizer has been mainly used a MAP equalizer. However, this turbo equalizer has a disadvantage that has a high computational complexity. To overcome the disadvantage and to improve efficiency of bandwidth, blind turbo equalization system is proposed. blind turbo equalization system has low equalization performance than conventional turbo equalization system. To circumvent this problem, we adapt the beamforming method based on the MUSIC algorithm. we confirmed that the proposed method improves the equalization performance.
Park, Un-Hee;Oh, Dae-Sub;Kim, Young-Min;Kim, Soo-Young
The Journal of Korean Institute of Communications and Information Sciences
/
v.35
no.5A
/
pp.423-430
/
2010
The performances of turbo-coded space-time block coding (STBC) schemes are subject to how soft decision detection (SDD) information are generated from the STBC decoder. For this reason, we have to pay particular attention to estimation of SDD. In this paper, we evaluate the performance of a turbo coded STBC scheme depending on the accuracy of the SDD. Recently, a new quasi orthogonal STBC (QO-STBC) scheme using a noise whitened filter was proposed in order to reduce noise enhancing effect of zero forcing detection process. This QO-STBC scheme was proven to be efficient in computational complexity compared to the other conventional QO-STBC schemes. In this paper, we first present detailed mathematical analysis on the noise whitened QO-STBC scheme, and by using the result we propose the optimum SDD method.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.