• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.4
• /
• pp.328-332
• /
• 2011

The formation of front metal contact silicon solar cells is required for low cost, low contact resistance to silicon surface. One of the front metal contacts is Ni/Cu plating that it is available to simply and inexpensive production to apply mass production. Ni is shown to be a suitable barrier to Cu diffusion into the silicon. The process of Ni electroless plating on front silicon surface is performed using a chemical bath. Additives and buffer agents such as ammonium chloride is added to maintain the stability and pH control of the bath. Ni deposition rate is found to vary with temperature, time, utilization of bath. The experimental result shown that Ni layer by SEM (scanning electron microscopy) and EDX analysis. Finally, plated Ni/Cu contact solar cell result in an efficiency of 17.69% on $2{\times}2\;cm^2$, Cz wafer.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.11
• /
• pp.2637-2642
• /
• 2009

In this present paper, we prepared $MWCNT/TiO_2$ composites by using pre-oxidized multi-walled carbon nanotubes (MWCNTs) with different titanium alkoxide precursors in benzene solvent. The composites were comprehensively characterized by BET surface area, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), energy dispersive X-ray analysis (EDX) and UV-Vis absorption spectroscopy. The photoactivity of the prepared materials, under UV irradiation, was tested using methylene blue (MB) in aqueous solution. Finally, according to the results of MB removal experiment, it can be considered that the MB degradation infect mainly caused by photocatalytic effect of $TiO_2$. Furthermore, the bactericidal test of the composites was also determined. It was indicated that $MWCNT/TiO_2$ composites with sunlight had greater effectiveness for B. cereus, S. aureus and E. coli than any other experimental conditions.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.15 no.4
• /
• pp.502-506
• /
• 2012

In order to find the structural characteristics of the thin films of group II-VI semiconductor compounds compared with those of powder materials, films were made of 4 powders of ZnS, CdS, CdSe, and CdTe(Aldrich), each with 99.99 % purity. For the ZnS/CdS multi-layers, the ZnS layer was coated over the CdS layer on an $AlO_x$ membrane, which served as a protective layer within a vacuum at the average speed of 1 ${\AA}$/sec. After studying the structures of the group II-VI semiconductor thin films by using X-ray spectroscopy, we found that the ZnS, ZnS/CdS, CdS, and CdSe films were hexagonal and exhibited some degree of preferred orientation. Also, the particles of the thin films of II-VI semiconductor compounds proved to be more homogeneous in size compared to those of the powder materials. These results were further verified through scanning electron microscopy(SEM), EDX analysis, and powder and thin film X-ray diffraction.

• Journal of the Korean institute of surface engineering
• /
• v.36 no.1
• /
• pp.89-98
• /
• 2003

Corrosion characteristics of Ti, Ti/Cr coated and plasma-nitrided surface for stainless steel containing Ti have been studied. Stainless steels containing 0.09-0.92wt% Ti were fabricated by using vacuum furnace and solutionized for 1hr at $1050^{\circ}C$. Ti and Cr coatings were done on solutionized stainless steel surface by EB-PVD. The Ti coated specimen were coated by Cr and were nitrided by plasma at $450^{\circ}C$ for 5hr Microstructure and phase analysis were performed using SEM, OM and EDX. Corrosion behavior of the coated specimen was investigated by electrochemical test. The coated surface was of fine columnar structure. The Ti/Cr coated surface was denser than the Ti coated and the Ti coated-nitrided surfaces. The corrosion and pitting potential increased in proportion to the Ti content, coating temperature, coating thickness and formation of stable oxide film. The current density in active and passive region decreased in the case of Ti/Cr coated sample and Ti coated-nitrided samples. Especially the plasma nitrided specimen after Ti coating have a good corrosion resistance compared with the Ti coated specimen. The number and size of pits decreased as Ti content of matrix increased.

• Proceedings of the KIEE Conference
• /
• 2003.07c
• /
• pp.1932-1934
• /
• 2003

본 논문은 신경전달물질 중 우울증, 신부전증의 지표 물질인 세로토닌의 농도를 극미량의 시료를 사용하여 정량할 수 있는 방법을 개발하기 위해 초소형 효소 고정화 전극을 개발하였다. 전극은 실리콘 웨이퍼 상에 반도체 공정을 이용하여 마이크로 크기의 Pt 박막 전극을 제작하였고, 전기화학적 방법으로 pyrrole 단량체를 Pt 전극 상에 순환전압전류법을 이용하여 산화적으로 전기 중합하였다. 효소의 고정은 일정 전압을 인가한 시간대 전류법으로 고정화하였다. 제작된 전극은 시간대 전류법으로 세로토닌의 농도에 따른 감도를 측정하였다. 세로토닌의 농도 범위 $1.0{\mu}mol/L{\sim}10mmol/L$에서의 감도는 $7.0{\mu}$A/decade를 나타내었으며, 실험결과에 따라 전극의 표면에서 발생하는 전류는 세로토닌의 농도에 비례함을 알 수 있었다. 전극의 표면분석은 Scanning Electron Microscopy(SEM), Energy Dispersive X-ray Spectroscopy(EDX) 그리고 Auger Electron Spectroscopy(AES)를 이용하여 분석하였다.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.4
• /
• pp.659-664
• /
• 2010

The ZnS/CdS thin films were made using 99.99% ZnS and CdS(Aldrich) powders in $7{\times}10^{-6}torr$. The ZnS layer was coated over the CdS layer on an AlOx membrane within a vacuum, at the average speed of $1{\AA}/sec$. After studying the ZnS/CdS and CdS thin films(both with the dimensions of 2.52nm), using fluorescence spectroscopy and comparing the respective results together, we found that although both of the resulting spectra peaked at 390nm, the ZnS/CdS thin films showed a narrower peak, and a higher intensity of photoluminescence than the CdS thin films. The particles of ZnS/CdS thin films also proved to be more homogeneous in size. In addition, the ZnS layer acted as a protective layer. Also, after studying the spectra of ZnS/CdS thin films taken 30 days after their preparation, we found no signs of aging. These results were verified through the scanning electron microscopy(SEM), EDX analysis, thin film X-ray diffraction, and luminescence spectroscopy.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.221-223
• /
• 1999

In this work, samples were manufactured variously by changing conventional calcining and sintering conditions and we tried the utilization by making the heat treatment time, which is demanded to high-Tc phase formation, much shorter. We found out optimal heat treatment conditions with the analysis on formation process at superconducting phase in term of the change of calcining and sintering time and then, examined X-ray diffraction(XRD) patterns, scanning electron microscope(SEM) measurement and energy dispersive X-ray spectrometer(EDX) of the samples manufactured under heat treatment conditions which we suggest here. As a result, 2223 high-$T_c$, phase of (Bi,Pb)SrCaCuO superconductor starting with ($Bi_l$ xPbx,)$_2$$Sr_2$$Ca_2$$Cu_3$$O_y$, composition was formed from 1 hr sintering sample at temperature nearby melting point and also the completed sample with calcining and sintering time of 9 hr was formed high-$T_c$.low-$T_c$ phase appearing in sight above the critical temperature of liquid $N_2$.

• Journal of Welding and Joining
• /
• v.25 no.4
• /
• pp.72-78
• /
• 2007

Aluminized steel sheet is a material with excellent heat resistance, thermal reflection and corrosion resistance. It has wide applications, owing to its low cost and excellent performance, in the petrochemical industry, electric power and other energy conversion systems, etc and has attracted the attention of many investigators. But the welding of aluminized steel sheet has a problem of decreasing tensile-shear strength, caused by mixed Al in the weld. This study investigated behavior of Al and its structural properties to resolve this problem. Several analysis equipment(SEM, EDX, EPMA) were used to investigate Al element in the weld. Also microhardness tester and TEM equipment were used to find the intermetallic compound. As a result of this study, Al-rich zones existed in the weld and Fe-Al intermetallic compounds were found in these zones. At the same time, the weldability of aluminized stainless steel sheet was investigated and compared with that of aluminized steel sheet. Although there is a difference between the base metal of the low carbon steel and stainless steel, it is interpreted that a behavior of Al element in the weld is similar.

• Journal of Radiation Industry
• /
• v.5 no.2
• /
• pp.179-184
• /
• 2011

In this study, several anion exchange membranes were successfully prepared by radiation grafting of vinylbenzyl chloride (VBC) monomer onto a polyethylene-co-tetrafluoroethylene (ETFE) film and subsequent quaternarization with diamins such as 1,4-diazbicyclo[2,2,2]octane, N,N,N',N'-tetramethyl-1,3-diaminopropane, N,N,N',N'-tetramethyl-1,6-diaminohexane, and trimethylamine. The anion exchange capacities of the prepared membranes were determined by using acid-base titration method. The cross-sectional morphology of the membranes was studied by using SEM instrument. The cross-sectional distribution patterns of the grafted polymers with anion exchange functional groups were also studied by EDX analysis.

• Advances in environmental research
• /
• v.5 no.1
• /
• pp.61-77
• /
• 2016

$NanoTiO_2$ was synthesized by ultrasonication assisted sol-gel process and subjected to iron doping and carbon-iron codoping. The synthesized catalysts were characterized by XRD, HR-SEM, EDX, UV-Vis absorption spectroscopy and BET specific surface area analysis. The average crystallite size of pure $TiO_2$ was in the range of 30 - 33 nm, and that of Fe-$TiO_2$ and C-Fe $TiO_2$ was in the range of 7 - 13 nm respectively. The specific surface area of the iron doped and carbon-iron codoped nanoparticles was around $105m^2/g$ and $91m^2/g$ respectively. The coupled semiconductor photo-Fenton's activity of the synthesized catalysts was evaluated by the degradation of a cationic dye (C.I. Basic blue 9) and an anionic dye (C.I. Acid orange 52) with concurrent investigation on the operating variables such as pH, catalyst dosage, oxidant concentration and initial pollutant concentration. The most efficient C-Fe codoped catalyst was found to effectively destruct synthetic dyes and potentially treat real textile effluent achieving 93.4% of COD removal under minimal solar intensity (35-40 kiloLUX). This reveals the practical applicability of the process for the treatment of real wastewater in both high and low insolation regimes.