• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.4
• /
• pp.766-771
• /
• 2008

As the practical range of SAW Device extended into various fields including physical sensor, chemical sensor and ID Tag, the platform for various SAW Devices is required more than ever. While SAW ID or Sensors advanced remarkably, the development of platform which applies to SAW Sensor left much to be desired. Therefore this paper represents the SAW platform in order to use SAW ID such as ID Tag or Sensors more conveniently. The SAW platform consists of a RF module which can recognize SAW ID and a main module which has a hish performance processor in order to process the response signal of SAW ID. The main module which has a high performance processor is designed by GUI environmental type to ensure that users are able to use the platform more easily. In this paper, the SAW platform, which is based on ARM9 core processor, used Windows Embedded CE 6.0 OS which brings friendly interface to users. Also the developers can make less effort to design various applications with sensors.

• Journal of Welding and Joining
• /
• v.12 no.4
• /
• pp.41-49
• /
• 1994

This study is to compare the welding quality of API 5L-X65 Steel- pipe's for natural gas transmission piping applied by SAW at shop and by GTAW-SMAW at site. The results can be summarized as follows; 1) Tensile strength of the welded zone by SAW(611.5 MPa) and by GTAW-SMAW(608.6 MPa) was maintained greater than that of the base metal(583.5 MPa). 2) Hardness of the welded zone and HAZ by SAW(Hv 194.8) & GTAW-SMAW (Hv 196.1) was slightly increased above that of the base metal (Hv 168.8), but less than the maximum allowable hardness(Hv 248). 3) Impact value of the welded zone by SAW(126.8 J) & GTAW-SMAW(88 J) became lower than that of the base metal(282.5 J), but was above the requirement of API 5L(68J). 4) Microscopic structure of the welded zone and HAZ by both SAW & GTAW-SMAW became fine-grained.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.934-938
• /
• 2000

Built-up edge affects the surface integrity of the machined surface and tool wear. Tool geometry and cutting conditions are very important factors to remove BUE. In this paper, we optimized the geometry of the metal slitting saw .1nd cutting conditions to remove BUE by the experiment. In general, the metal slitting saw is plain milling cutter with thickness less of a 3/16 inch. This is used for cutting workpiece where high dimensional accuracy and surface finish are necessary. The experiment was planned with Taguchi method that is based on the orthogonal array of design factors(coating, rake angle, number of tooth, cutting speed, feed rate). Response table was made by the value of the surface roughness, the optimized tool geometry and cutting conditions through response table could be determined. In addition. the relative effect of factors were identified by the variance analysis. filially. coating and cutting speed turned out important factors.

• Journal of KSNVE
• /
• v.9 no.6
• /
• pp.1210-1217
• /
• 1999

This paper presents schematic process of identifying the principal cause to make the vibration problem of rotating circular saws. In the tandem pencil slat saw lines, feeding of cedar blocks is often stopped because excessive motro current is required in a saw motor. These events are called "kick-offs" in technical reports. Research on saw behavior at kick-offs is required to understand are reduce the frequency and severity of kick-offs events. This research aims at finding out the principal cause of kick-offs, and evloving design improvements for high cutting performance with fewer and less severe kick-offs. Measurements of critical speed, cutting force, cutting temeprature and dynamic displacements are carried out to observe the instability mechanism and also to obtain saw design parameters for the numerical analyses. And the numerical analyses involving FEM and multiple scale method are utilized to show the possibility of the principal cause.pal cause.

• Proceedings of the IEEK Conference
• /
• 2001.06a
• /
• pp.245-248
• /
• 2001

In this paper, we have investigated the design technique and fabricated the surface acoustic wave (SAW) filter for duplexer, which consists of Tx. and Rx. filter, and antenna terminal. For Tx. and Rx. bandpass filters we used the one-port SAW resonators with n-section ladder structure. The structure is composed of couples of series-arm resonators and parallel-arm resonators. RF filter using ladder structure was designed and fabricated on 36$^{\circ}$Y-X LiTaO$_3$ substrates. Designed filters, insertion loss is less than 1.5dB, the bandwidth is more than 25MHz, rejection band level is less than -30dB and center frequency is 820MHz.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.1
• /
• pp.10-15
• /
• 1999

We have studied a method to design and fabricate the Intermediate Frequency(IF) band pass filter with low shape factor which is used for CDMA base station on the 35°Y-cut X-propagation Quartz substrate. In order to fabricate a device of the low shape factor for the IF SAW filter on this substrate, we employed apodization weighted type interdigital transducer(IDT) as an input and withdrawal weighted type IDT as an output by using impulse modelling method. Also, using the Kaiser-Bessel window function, we have adopted 2200pairs and 1000pairs of input and oueut IDT respectively to minimize the effect of ripple. Furthermore, the width and the space of IDT finger are 3.6 ㎛ and 3.5 ㎛ respectively. Thus, we can have optimal results when the IDT thickness is 6000Å in consideration of the ratio of SAW's wavelength while it's aperture is 2mm for impedance matching. The fabricated SAW filter for CDMA had the property of almost 115.2MHz of a center frequency, less then 1.27MHz of bandwidth, less than 1.3 of shape factor, - l5dB of out band attenuation insertion loss and -45dB of rejection band.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1998.04a
• /
• pp.187-193
• /
• 1998

In the tandom pencil slat saw lines, feeding of cedar blocks is often stopped because excessive motor current is required in a saw machine. These events are called "kickoffs' in factory lines. Kickoffs decrease productivity due to machine down-time and damage to saw blades often accompanies them. Researches on saw behavior at kickoff are required to understand and reduce the frequency and severity of kickoff events. This research aims at understanding the fundamental mechanisms of kickoffs during cutting, predicting the impending kickoff and evolving design improvements for high cutting performance with fewer and less severe kickoffs.offs.

• Journal of the Korean Society of Safety
• /
• v.20 no.2 s.70
• /
• pp.98-104
• /
• 2005

Saw dust concrete f3r finding out insulation characteristic was tested using test plate $30cm{\times}30cm{\times}5cm$. basically, molds f3r the test of compressive, tensile, normal without sawdust, $0.05\%,\;0.1\%,\;0.2\%,\; 0.4\%,\;0.6\%,\;0.8\%,\;1.0\%,\;1.2\%,\;1.4\%,\;1.6\%,\;1.5\%,\;2.0\%$, mixing proportion. heat conductivity of the saw dust concrete mixed with the above proportion was taken in this study. Thermal conduction of normal concrete depends on mixing proportion strength aggregate character, water content. all these items are specified here in fables. $1.8\%\~2.0\%$ saw-dust mising concrete shows as the faction as normal insulation material has its function. and the higher saw-dust mixing rate becomes, the thermal conduction becomes the less Then, the conclusions are that saw-dust using concrete has better insulation function than normal concrete.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.3
• /
• pp.678-684
• /
• 2013

This paper describes a low-power baseband circuit for SAW-less LTE-Advanced transmitters. The proposed transmitter baseband circuit consists of a 2nd-order Tow-Thomas type active RC-LPF and a 1st-order passive RC LPF. It can provide a 7 multi-channel cut-off frequencies and wide gain control range of -41 dB ~ 0 dB with a 1-dB step. The proposed 2nd-order active RC-LPF adopts an op-amp in which three other sub-op amps are in parallel connected to reduce DC current for different cutoff frequency. In addition, each sub-op amp adopts both Miller and feed-forward phase compensation method to achieve an UGBW of more than 1-GHz with a small DC power consumption. The proposed baseband circuit is implemented in 65-nm CMOS technology, consuming DC power from 6.3 mW to 24.1 mW from a 1.2V supply voltage for each different cut-off frequency.

• Korean Journal of Crystallography
• /
• v.2 no.2
• /
• pp.32-40
• /
• 1991

The effects of compositional variation, rotation speel and pulling rate on the growth of optical quality Bi120e02(1 crystals were examined. It was found to flatten the shape of crystal-melt interface for yowing a single crystals less than about 30mm in diameter at the rotation speed of 50rpm. Diameter of crystals with flat interface was increased as the pulling rate. The precipitation of Bi40e3012 phase set limits to pulling rate of BGO crystals. Precipitate-free BGO crystals were grown under pulling rate of 2mm l hr which released the stress resulted from too hi어 Pulling rate, and from 6. IBi203·GeO2 batch composition obtained by addition of 0.1 mole Bi203 into Bi-deficient melts to fill up the deficiency resulted from gradual volatilization of Bi2O). The pale-yellow colored crystals had good quality in that dislocation density was less than 103pits/cm, and it also exhibited transmittance of 70% and optical activity of 23°/mm. and SAW velosity was measured 1700m/sec on 111 cut 110 propagating BGO crystals. The SAW filter with electrode thickness of 9.8um was fabricated by using the electron beam and dry etching technique, it makes Bi12GeO20 devices intersting for color TV IF with half device size.