• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.1
• /
• pp.125-133
• /
• 2006

It is important to understand flow characteristics and performances of sails for both sailors and designers who want to have efficient thrust of yacht In this Paper the viscous flows around sail-like rigid wings, which are similar to main and jib sails of a 30 feet sloop, are calculated using a CFD tool. Lift, drag and thrust forces are estimated for various conditions of gap distance between the two sails and the center of effort of the sail system is obtained. Wind tunnel experiments are also carried out to measure aerodynamic forces acting on the sails system and to validate the computation. It is found that the combination of two sails produces the lift force larger than the sum of that produced separately by each sail and the gap distance between the two sails is an important factor to determine total lift and thrust.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1539-1543
• /
• 2006

We have developed self-aligned imprint lithography (SAIL) technology, an innovative method for roll-to-roll (R2R) fabrication of electronic devices on flexible plastic substrates. In this paper, we present the first R2R-produced ${\alpha}$-Si TFTs built on a polyimide substrate using the SAIL process, and prove the feasibility of this technology to enable R2R fabrication of flexible display active matrix (AM) backplanes with high precision and throughput.

• Textile Coloration and Finishing
• /
• v.24 no.1
• /
• pp.54-61
• /
• 2012

This study surveyed the preparation of 8oz coated fabric and the physical property of the coated fabric according to the treated condition for the sail yacht. And the coated fabrics were compared with the performance of overseas products for verification. Physical properties of the coated fabric treated with non-yellowing functional polyurethane resin were examined according to the treatment condition such as compression and ageing treatments. Finally, yellowing fastness to light for 60 hours was assessed. Considering the compression condition after coating, good physical property was obtained at $6kgf/cm^2$. Also, the performance of yellowing fastness was similar to performance of overseas goods.

• Journal of Ocean Engineering and Technology
• /
• v.35 no.5
• /
• pp.360-368
• /
• 2021

The need for energy harvesting in marine environments is gradually increasing owing to the energy limitation of marine robots. To address this problem, a catamaran-type sail drone (CSD), which can harvest marine energies such as wind and solar, was proposed in a previous study. However, it was designed and manufactured without considering the stability, optimal hull-form, and maintenance. To resolve these problems, a CSD with two keels, a performance estimator, V-shape hulls, and modularized components is proposed and its mechanism is developed in this study. To verify the performance of the CSD, the performance estimation using smoothed-particle hydrodynamics (SPH) and the heading control using fuzzy logic controller (FLC) are performed. Simulation results show the attitude stability of the CSD and the experimental results show the straight path of the CSD according to wind conditions. Therefore, the CSD has potential applications as an energy harvesting system.

• Journal of Advanced Marine Engineering and Technology
• /
• v.30 no.1
• /
• pp.109-115
• /
• 2006

An overview of 30 feet sailing yacht design is presented. with an emphasis on the factors contributing to start-up Popularization . After prescribing the configurations of the purposed yacht. the design of the hull form with a rudder and a keel, are schematically described. Also the determinations of the dimensions of the sail and rig are performed.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2005.06a
• /
• pp.818-823
• /
• 2005

An overview of 30 feet sailing yacht design is presented, with an emphasis on the factors contributing to start-up popularization. After prescribing the configurations of the purposed yacht, the design of the hull form with a rudder and a keel, are schematically described. Also the determinations of the dimensions of the sail and rig are performed.

• Journal of the Society of Naval Architects of Korea
• /
• v.43 no.4 s.148
• /
• pp.504-511
• /
• 2006

In this paper a modern sailing boat for our costal area was developed by using the traditional boat hull form. Main particulars of design ship were determined by using the statistical values. Hull form was varied from the traditional boat hull form which was selected by the previous study and modified to fit Lateen sail. The appendage, rudder and keel were designed for good performance of against wind sailing. The performance of hull form was examined and the results were shown.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2008.10a
• /
• pp.82-85
• /
• 2008

We are working towards large-area arrays of thin film transistors on polymer substrates using roll-to-roll (R2R) processes exclusively. Self-aligned imprint lithography (SAIL) is an enabler to pattern and align submicron features on meter-scaled flexible substrates in the R2R environment. The progress, current status and remaining issues of this new fabrication technology are presented.

• Journal of the Society of Naval Architects of Korea
• /
• v.60 no.5
• /
• pp.351-357
• /
• 2023

In this study, we devised methods to enhance the efficiency of rotor sails which have been applied as one of the energy saving devices of ships. The idea of the study originated from the notion that installing protrusions or increasing the surface roughness on the smooth surface of the rotor sail could delay the separation of the incoming wind flow and consequently increase the lift force. Five cylinder models were considered and tested in an open-type wind tunnel at Chungnam National University. A smooth surface cylinder exhibits the highest lift-to-drag ratio at a specific Reynolds number, and as the Reynolds number increases this value decreases sharply. The variation in this typical Magnus force can be significantly improved by altering the surface shape and roughness of the rotor sail. It has been observed that increasing the surface roughness improves the lift characteristics, resulting in increased efficiency. Furthermore, it revealed that the reverse Magnus effect which may occur during actual operation in the low spin ratio region can be significantly enhanced.

• KEPCO Journal on Electric Power and Energy
• /
• v.5 no.3
• /
• pp.135-140
• /
• 2019

Lattice towers and tubular steel poles have been commonly used for electrical power transmission in Korea. They are durable, structurally stable, simple and can easily be constructed in limited spaces. However, residents are opposed to construct transmission lattice towers in their areas because they are not visually attractive, and electrical field occur at the transmission lines. Underground transmissions have been used instead of the traditional towers to resolve these problems, however they are not cost effective to construct and run. Therefore, we have developed eco-friendly towers that are more attractive, well blending into the surrounding environment, and much more economical than underground transmissions. There are four categories of the eco-friendly electric transmission towers about design aspects. Firstly, there is decoration type such as tree tower and ensemble tower. Tree tower looks like actual trees with leaves and branches so it blends into surroundings. Ensemble towers were designed after pair of crane birds. Those towers have decoration features and art works. Structural examination and manufacturing this type would be very similar to the conventional transmission towers. Secondly, there is arm design type such as traditional tower. Design features are added to the existing towers. As partial design can be adoptable on these types, it can easily meet height regulations and attach to conventional lattice towers and tubular steel poles. Also, these towers are more economical than others. Third category is multipurpose type such as Sail Tower. These towers have simple pole or tubular structure with features which can be used as information message board, public relations and much more. This type will face greater wind pressure because of the area of the board, also visibility must take into consideration. Lastly, there is moulding type such as arc pylon. It is different shape to the conventional towers - lattice towers and tubular steel poles. Dramatic design changes have been adapted - from a hard and static tower to a soft and curved tower. These towers will well stand out in the field. However, structural examination and manufacturing this type would be difficult and costly. Also certain towers of this type would require scaffolding or false work to construct, which will result in limitations of the construction area. This paper shows KEPCO 154 kV Sail tower in detail. KEPCO 154 kV Sail tower that is included in fabrication of sample tower and tower testing has developed and the results are presented in this paper. We hope that sail tower is also considered as a solution to have public acceptance or to create a familiar atmosphere among towers and people in coastal area.