• 대한기계학회논문집A
• /
• 제33권10호
• /
• pp.1158-1162
• /
• 2009

Fatigue limit of the copper film coated by Sn was estimated using Goodman diagram and Gerber diagram. To obtain the high cycle fatigue life curve, S-N curve, of the film, the high cycle fatigue test was carried out by applying the constant amplitude load to the film specimen with three different stress ratio of 0.05, 0.3 and 0.5 and the frequency of 40 Hz at room temperature in air. The free-standing film specimen 15.26${\mu}m$ thick was fabricated by etching process. The fatigue limits and S-N curves at the respective stress ratios were determined from the experimental works. It was shown that the S-N curves were dependent on the stress ratio and the fatigue limit was increased with decreasing the stress ratio. The dependency of the fatigue behavior was presented in empirical relationship. Using these relationships, the fatigue limit was predicted.

• 대한기계학회논문집A
• /
• 제24권3호
• /
• pp.761-768
• /
• 2000

In order to investigate how the fatigue damage effects on the critical properties of superconductor, a fatigue test at room temperature and an Ic measurement test at 4.2K were carried out in this study, respectively, using a 9 strand Cu-Ni/NbTi/Cu composite cable. Through the fatigue test of a 9 strand Cu-NUNbTi/Cu composite cable, a conventional S-N curve was plotted even though there was a possibility of fretting among strands. It was found that the maximum stress corresponding to the inflection point on the S-N curve obtained was nearly the same value as the yielding strength of cable obtained from the static tensile test. However, the effect of cabling in multi-strands superconducting cable on the fatigue strength was not noticeable. The critical current(Ic) measurement was carried out at 4.2K in a NbTi strand out of the fatigued cable. It showed a degradation of lc at high stress amplitude regions over 380NTa, and the degradation became significant as the applied stress amplitude increased.

• 한국자동차공학회논문집
• /
• 제12권4호
• /
• pp.207-212
• /
• 2004

Full-beads of multi-layer steel engine head gaskets that are used to seal the combustion gas between the head and the block are subject to cyclic bending stresses due to the variation of the head/block gap during engine operation. The S-N curve for the fatigue durability assessment of the full-bead formed on NBR-coated SUS301 thin plate is deduced from the axial fatigue test results because of the difficulty in conducting the bending fatigue test of thin plate. The experimental verification of the deduced S-N curve is presented. It is shown that the NBR coating increases the endurance limit of the plate significantly. Mechanism of crack nucleation and propagation in the full-bead is discussed with photographs of the fatigue cracks.

• 대한금속재료학회지
• /
• 제49권10호
• /
• pp.774-779
• /
• 2011

S-N fatigue behavior of cast 304 stainless steel was studied at 25, -50 and $-196^{\circ}C$ and at a stress ratio of -1 in uniaxial and bending loading condition. It was found that the resistance to S-N fatigue was greatly improved with decreasing testing temperature. The normalized S-N fatigue curves by tensile strength at three different testing temperatures matched each other, suggesting that tensile strength determines the S-N fatigue resistance of cast 304 stainless steel at low temperatures. The effects of different loading on the resistance to S-N fatigue of cast 304 stainless steel were quantified. The S-N fatigue curves at 25, -50 and $-196^{\circ}C$ were described by using Basquin's law the relationship between the S-N fatigue curve and the testing temperature was obtained by using a simple regression method.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2007년도 춘계학술대회 논문집
• /
• pp.123-124
• /
• 2007

• 대한수학회지
• /
• 제33권2호
• /
• pp.367-379
• /
• 1996

Let $V = {(z, y) : f(z, y) = z^n + Ay^\alpha z^p + y^\beta z^q + y^k = 0}$ and $W = {(z, y) : g(z, y) = z^n + By^\gamma z^s + y^\delta z^t + y^k = 0}$ be germs of analytic irreducible subvarieties of a polydisc near the origin in $C^2$ with n < k and (n, k) = 1 where A and B are complex numbers. Assume that V and W are topologically equivalent near the origin.

• 물과 미래
• /
• 제15권2호
• /
• pp.33-39
• /
• 1982

본 논문에서는 우리나라의 3개 단일목적댐(춘천, 청평, 화천)과 3개 다목점댐(소양, 안동, 대청)의 월 유하량 자료를 Thomas-Fiering 법과 조화함수법으로 50년간 모의발생하여 한계용량의 개념에 의하여 해석하였으며 조기별(월의 수) 단일목적 저수지와 다목적 저수지의 한계용량을 결정하였다. 그 결과 다음과 같은 Feller 형의 공식을 얻었다. (1) 단일목적 저수지 $R_n=2.8357 I\sqrt{n}$ (2) 다목적 저수지 $R_n=2.5145 I\sqrt{n}$ 그러므로 우리나라의 댐 지점에서의 월유하량은 Thomas-Fiering 법이 적합하며 Rippl의 누가곡선법에 의하지 않고 위의 공식에 의하여 주기별 한계용량을 쉽게 구할 수 있다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.272-277
• /
• 2001

In order to evaluate variation of fatigue data of the LP steam turbine blade steel, it is important to estimate P - S - N curves to accurately define the probability distributions. In this study, new procedure is introduced to determine the expression of P - S - N curves. For this purpose, 3-parameter Weibull distribution was found to be most appropriate among assumed distributions when the probability distributions of the fatigue life were examined by the proposed analysis. Furthermore, parameter estimation for P - S - N curves was performed using various optimization to maximize the correlation coefficient. As a result of this, sequential linear programing method is used for estimation of P - S - N curves.

• 대한기계학회논문집A
• /
• 제27권5호
• /
• pp.724-733
• /
• 2003

Fatigue design rules for welds in the ASME Boiler and Pressure Vessels Code are based on the use of Fatigue Strength Reduction Factors(FSRF) against a code specified fatigue design curve generated from smooth base metal specimens without the presence of welds. Similarly, stress intensification factors that are used in the ASME B3l.1 Piping Code are based on component S-N curves with a reference fatigue strength based on straight pipe girth welds. But the determination of either the FSRF or stress intensification factor requires extensive fatigue testing to take into account the stress concentration effects associated with various types of component geometry, weld configuration and loading conditions. As the fatigue behavior of welded joints is being better understood, it has been generally accepted that the difference in fatigue lives from one type of weld to another is dominated by the difference in stress concentration. However, general finite element procedures are currently not available for effective determination of such stress concentration effects. In this paper, a mesh-insensitive structural stress method is used to re-evaluate the S-N test data, and then more effective method is proposed for pressure vessel and piping fatigue design.

• 연구논문집
• /
• 통권34호
• /
• pp.59-68
• /
• 2004

The hot spot stress approach and the notch strain approach are discussed with some results of them. And a stress model that can be applicable to several types of weld joints with single S-N curve of the base material. The stress model uses the geometric characteristics of the stress distribution vicinity of weld joints. The model was applied to five different weld joins(the base material is SM490B). By the representative stress, the experimental fatigue data are plotted very closely to the S-N curve of the base material.