• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.21 no.5
• /
• pp.830-835
• /
• 2012

A research for application of LDSMC(Low Density Sheet Molding Compound) composite is in progress for lightening the weight. This paper has performed fatigue test and simulation of external panel for Korean commercial vehicle. Before the fatigue test, static test was carried out. From the test, the structural safety was investigated using Goodman diagram. After the static test performance, the fatigue test was conducted at a range of load frequency 5Hz, a stress ratio(R) of 0.05 and an endurance limit of $10^6$ to obtain the S-N curve. The S-N curve is applied to the fatigue analysis of the external panel assembly. The result of FEM analysis was in accord with the experimental result within 83% confidence. It showed that the process to set up the safety range of allowable error is required in process of the design and simulation verification.

• Transactions of Materials Processing
• /
• v.13 no.8
• /
• pp.731-737
• /
• 2004

Mechanical properties such as Young's modulus and hardness of thin film in coated steel are difficult to determine by nano-indentation from the conventional analysis using the load-displacement curve. Therefore, an analysis of the nano-indentation loading-unloading curve was used to determine the Young's modulus, hardness. A new method is recently being developed for elastic-plastic properties of materials from nano-indentation. Elastic modulus of the thin films shows relatively small influence whereas yield strength is found to have significant effect on measured data. The load-displacement curves of material tested with a Berkovich indenter and nano-indentation continuous stiffness method is used to measure the modulus and hardness through thin films, and then these are computed using the analysis procedure. The developed neural networks apply also to obtain reliable mechanical properties.

• Proceedings of the KIEE Conference
• /
• 1996.11a
• /
• pp.163-165
• /
• 1996

In this paper, we are proposed development of electric energy method and load curve. A daily electric energy is forecasted using artificial neural network. The load curve is obtained by combining forecasted electric energy and typical daily load patterns which are classified using KSOM and Fuzzy system. As a result, we know that we could get more accurate results and easier application than the results from based on the hourly historical data.

• Journal of the Korean Society for Precision Engineering
• /
• v.33 no.9
• /
• pp.745-751
• /
• 2016

This paper presents the acceleration and deceleration control of free-form surfaces. A rapid variation of acceleration (or Deceleration) drives the system into a machine shock, resulting in the inaccuracy of the path control of the NURBS curve. The pattern of acceleration control can be established using the curvature of the NURBS curve. The curvature can be easily calculated from the first and second derivative of the NURBS curve used in Taylor's expansion for NURBS interpolation. However, the derivatives are not used in the recursive method for NURBS interpolation. Hence, we attempted the difference-derivatives for calculating the NURBS curvature. Both, Taylor's expansion and the recursive method, are used jointly for controlling the acceleration in the same interpolation algorithm.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2017.10a
• /
• pp.581-583
• /
• 2017

Elliptic curve cyptography is relatively a current cryptography based on point arithmetic on elliptic curves and the Elliptic Curve Discrete Logarithm Problem (ECDLP). This discrete logarithm problems enables perfect forward secrecy which helps to easily generate key and almost impossible to revert the generation which is a great feature for privacy and protection. In this paper, we provide a lightweight Elliptic Curve Diffie-Hellman (ECDH) Key exchange generator that creates a 163 bit long shared key that can be used in an Elliptic Curve Integrated Encryption Scheme (ECIES) as well as for key agreement. The algorithm uses a fast multiplication algorithm that is small in size and also implements the extended euclidean algorithm. This proposed architecture was designed using verilog HDL, synthesized with the vivado ISE 2016.3 and was implemented on the virtex-7 FPGA board.

• Journal of Ocean Engineering and Technology
• /
• v.17 no.2
• /
• pp.34-39
• /
• 2003

Recent deepwater offshore structures in the Gulf of Mexico utilize butt welded tubular joints. Application of a welded tubular joint includes tendons, production risers, and steel catenary risers. Fatigue life assessment of these joints becomes more critical, as the structures to which they are attached are allowed to undergo cyclic and sometimes large displacements around an anchored position. Estimation of the fatigue behavior of these tubular members in the design stage is generally condrcted by using S-N curves, as specified in the codeds and standards. Applying the stress concentration factor of the welded structure to the S-N approach often results in a very conservative assessment, because the stress field acting on the tubular has a non-uniform distribution through the thickness. Fatigue life analysis using fracture mechanics has been applied in the design of the catenary risers. This technology enables the engineer to establish proper requirements on weld quality and inspection acceptance criteria to assure satisfactory structural integrity during its design life. It also provides guidance on proper design curves and a methodology for accounting for the effects of non-uniform stress distribution through the wall thickness. Still, there is inconsistency when designing tubular joints using a conventional S-N approach and when specifying weld flaw acceptance criteria using fracture mechanics approach. This study developed fatigue curves that are consistent with both the S-N approach and the fracture mechanics approach. Accounting for non-uniform stress distribution and threshold stress intensity factor were key parameters in relating both approaches. A series of S-N curves, generated from the fracture mechanics approach, were compared to the existing S-N curves. For flat plate butt joint, the S-N curve generated from fracture mechanics matches with the IIW class 100 curve when initial crack depth was 0.5 mm (0.02 ). The new curves for tubular joint agree very well with the experimental results. The comparison also indicated the degree of conservatism built into the API X design curve.

• Composites Research
• /
• v.18 no.1
• /
• pp.38-44
• /
• 2005

In this paper, the group velocity dispersion curves of the $S_o$ symmetric mode in unidirectional CFRP plate was calculated as varying the propagating direction. The group velocity curve was obtained with the group velocities of the $S_o$ symmetric mode corresponding to 0.2 MHz-mm under the first cut-off frequency in the dispersion curves, and corrected by introducing the slowness curve. The velocities of the $S_o$ symmetric mode in the unidirectional CFRP plate were measured as varying the propagating direction and compared with the col?rotted group velocity curve. The measured velocities were good agreement with the corrected group velocity curve except near the fiber direction which was called the cusp region. It implies that the direction of the group velocities incline toward the fiber direction of the unidirectional CFRP plates when the propagation direction is not accorded with the principal axis. It is supposed that this phenomenon rerults from the preferential propagating the energy toward the direction with the faster propagation velocity.

• International Journal of Ocean Engineering and Technology Speciallssue:Selected Papers
• /
• v.6 no.1
• /
• pp.69-74
• /
• 2003

Recent deepwater offshore structures in the Gulf of Mexico utilize butt welded tubular joints. Application of a welded tubular joint includes tendons, production risers, and steel catenary risers. Fatigue life assessment of these joints becomes more critical, as the structures to which they are attached are allowed to undergo cyclic and sometimes large displacements around an anchored position. Estimation of the fatigue behavior of these tubular members in the design stage is generally conducted by using S-N curves, as specified in the codes and standards. Applying the stress concentration factor of the welded structure to the S-N approach often results in a very conservative assessment, because the stress field acting on the tubular has a non-uniform distribution through the thickness. Fatigue life analysis using fracture mechanics has been applied in the design of the catenary risers. This technology enables the engineer to establish proper requirements on weld quality and inspection acceptance criteria to assure satisfactory structural integrity during its design life. It also provides guidance on proper design curves and a methodology for accounting for the effects of non-uniform stress distribution through the wall thickness. Still, there is inconsistency when designing tubular joints using a conventional S-N approach and when specifying weld flaw acceptance criteria using fracture mechanics approach. This study developed fatigue curves that are consistent with both the S-N approach and the fracture mechanics approach. Accounting for non-uniform stress distribution and threshold stress intensity factor were key parameters in relating both approaches. A series of S-N curves, generated from the fracture mechanics approach, were compared to the existing S-N curves. For flat plate butt joint, the S-N curve generated from fracture mechanics matches with the IIW class 100 curve when initial crack depth was 0.5 mm (0.02). The new curves for tubular joint agree very well with the experimental results. The comparison also indicated the degree of conservatism built into the API X design curve.

• Nuclear Engineering and Technology
• /
• v.4 no.1
• /
• pp.3-10
• /
• 1972

In order to verify the contribution of scattered photons in a restricted gamma-cell as a cause of the“before glow”on a thermoluminescent glow curve of natural quartz, the ratio of the scattered to primary radiation contributions (S/P) in the cell is measured and the relationship between the effective“before glow”height ( $h_{b}$) and S/P ratio is quantitatively investigated. The result shows quite good linear relationship between them with a correlation coefficient of ＋0.9, which possibly suggests that the electrons originally released by the photons of reduced energy are trapped in the shallower traps. Moreover, the ratios of $h_{b}$ to total glow area (At) and of effective “before glow”area (Ab) to At are also examined to see the relationships between S/P and each of them, respectively. The relationships are represented by exponential functions in the region of S/P greater than 0.035. Finally, the exposure limit for re-use of the natural quartz as a TLD was found to be approximately 10$^{5}$ R by analyzing total thermoluminescent output and corresponding exposure dose.ose.

• Proceedings of the KIEE Conference
• /
• 1990.11a
• /
• pp.157-160
• /
• 1990

A dot matrix type DC Plasma Display Panel was fabricated and it's characteristics was investigated. Paschen curve and I-V curve of various gas mixture was given. Optimal gas mixing ratio, pressure and operating point was determined. The priming effect was observed and discharge delay time was measured with varing applied voltage, priming current, priming distance, duty ratio.