• International Journal of Fluid Machinery and Systems
• /
• v.4 no.1
• /
• pp.199-208
• /
• 2011

This work presents numerical results, using OpenFOAM, of the flow in the swirl flow generator test rig developed at Politehnica University of Timisoara, Romania. The work shows results computed by solving the unsteady Reynolds Averaged Navier Stokes equations. The unsteady method couples the rotating and stationary parts using a sliding grid interface based on a GGI formulation. Turbulence is modeled using the standard k-${\varepsilon}$ model, and block structured wall function ICEM-Hexa meshes are used. The numerical results are validated against experimental LDV results, and against design velocity profiles. The investigation shows that OpenFOAM gives results that are comparable to the experimental and design profiles. The unsteady pressure fluctuations at four different positions in the draft tube is recorded. A Fourier analysis of the numerical results is compared whit that of the experimental values. The amplitude and frequency predicted by the numerical simulation are comparable to those given by the experimental results, though slightly over estimated.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.4
• /
• pp.418-423
• /
• 2014

Small hydropower has been considered as a solution to resolve the problem of exhaustion of fossil fuel and industrial pollution. In this study, we developed and tested a Cross-Flow Turbine with two guide vanes to optimize the small hydropower for the site condition with large fluctuation of head and flow rate. Furthermore, in the condition of constant inlet head, CFD analysis was carried out to analyze the effect of air suction and valve position on the performance characteristics. The results showed that the air suction can minimize the hydraulic loss caused by the Recirculation flow in the runner passage and flow impact on main shaft so that it can increase the turbine efficiency and output power.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2005.05a
• /
• pp.174-179
• /
• 2005

In the super slow speed die casting process, the casting defects due to melt flow should be controlled in order to obtain sound casting products. The casting defects that are caused by molten metal were cold shut formation, entrapment of air, gas, and inclusion. But the control of casting defects has been based on the experience of the foundry engineers. The calculation of simulation can produce very useful and important results. The calculation data of die casting process condition from the computer simulation by the Z-CAST is made to insure that the liquid metal is injected at the right velocity range and that the filling time is small enough to prevent premature solidification. The parameters of runner shape that affected on the optimized conditions that was calculated with simple equation were investigated. These die casting process control techniques of automobile valve body mid-plate have achieved good agreement with the experimental data of tensile strength, hardness test, and material structure photographies satisfactory results.

• Proceedings of the KSR Conference
• /
• 2005.11a
• /
• pp.897-901
• /
• 2005

21 century as the knowledge information anger society now our society industry of all fields the rolling stock maintenance conservative standardization enterprise where information anger is being turning out construction Ministry of Transportation supported with continuous development of the supply section substitution quantity information processing system which the information highway is quick and the Korean railroad technical research worker propelled the enterprise as the subjective agency, it contracted this for a vehicle field information anger system construction in link of the enterprise our construction and an agreement, information technique composed the consortium t9day and it propelled a system codevelopment. The SMSC who is a front-runner of Maj loach city railroad operation agency to 'here business relates with a vehicle field maintenance conservativeness an immediacy operation and generally and information anger it will plan it will integrate it will own jointly and business efficiency and in the dictionary an obstacle occurrence electromotive car maintenance conservative information and it will improve only maintenance conservativeness of preventive maintenance of the electromotive car it knows it will prevent to construct the maintenance conservative system of the preventive maintenance, it applied the RIMS project to sleep.

• Asia-Pacific Journal of Business
• /
• v.9 no.1
• /
• pp.77-89
• /
• 2018

Today, the sports teams are in a highly competitive environment where they don't know what may happen in the near future. While the front-runner teams suffer a serious slump, the teams in lower ladder stacks victories. This recent phenomenon proves that no team can secure the sustainable competitive edge over others. This is the time when a complete change of the mindset about the short-term competitive edge is needed. Therefore, we conducted the case study to the short-term competitive edges by selecting OK Savings Bank Rush & Cash volleyball team(hereafter referred to as OK Savings Bank). Thus, we presented the Transient Advantage Wave which describes the five stages of Initiating-Promotion-Utilization-Reconstruction-Withdrawal as a framework for the case study. Finally, we organized the results of the analysis and based on this result, we discussed the significance and the limitation of the short-term competitive edge that the sports team should pursue. This study contributed to the changes in strategies & tactics of various sports teams by suggesting the new strategy called short-term competitive edges that teams should utilize in order to get the best results in the sports league that has the strong quality of Time-based system.

• The KSFM Journal of Fluid Machinery
• /
• v.16 no.4
• /
• pp.10-14
• /
• 2013

In this study, we have numerically investigated the hydraulic efficiency with various values of discharge angle($11^{\circ}$, $12^{\circ}$, $14^{\circ}$, $15^{\circ}$, $17^{\circ}$, $18^{\circ}$, $20^{\circ}$) in the Francis turbine of hydropower generation under 15MW with fixed values of head range of 151m and flow rate($10.97m^3/s$). We also conducted the numerical analysis with constant inlet angle in the Francis turbine using the commercial code, ANSYS CFX. Hydraulic characteristics for different values of the runner blade angle are investigated. The results showed that the change of discharge angles significantly influenced on the performance of the turbine hydraulic efficiency.

• International Journal of Safety
• /
• v.9 no.2
• /
• pp.22-28
• /
• 2010

This paper describes a web-based design review system as a knowledge management system relating reliability and safety system design. Since people's consciousness for safety and security become sensitive and increases the need of establishing a proactive prevention method for internal failures and relating risks in products. It also means that prevailing tacit knowledge in retired workers, in order to transform them to be easily used to support new system development, become more important. When considering safety and reliability design, at least two data sheet are necessary; Failure Modes and Effects Analyses (FMEA) and Risk Assessment (RA). These two data are practically made separately. However, it includes the concerns that a risk by failures during long-term use may not be noticed. To overcome this insufficiency, a support tool for integrating reliability evaluation and risk assessment data simultaneously is expected to be revealed. The authors have then developed a web-based design review system for reliability and safety system design. The system include various profitable functions; making FMEA and RA sheet, retrieving past data sheet for engineering change management and new product development and web-based discussion to increase the efficiency of discussion. The system is applied to one practical development works in order to demonstrate its effectiveness that is to be made clear by interviewing user's qualitative comment.

• Design & Manufacturing
• /
• v.10 no.2
• /
• pp.50-54
• /
• 2016

In the semiconductor industry the final products were checked for several environments before sell the products. The burning test of memory and chip was implemented in reliability for all of parts. The memory and chip were developed to high density memory and high performance chip, so circuit design was also high integrated and the test bed was needed to be thin and fine pitch socket. LGA(Land Grid Array) IC socket with thin wall thickness was designed to satisfy this requirement. The LGA IC socket plastic part was manufacture by injection molding process, it was needed accuracy, stiffness and suit resin with high flowability. In this study, injection molding process analysis was executed for 2 and 4 cavities moldings with runner, gate and sprue. The warpage analysis was also implemented for further gate removal process. Through the analyses the total deformations of the moldings were predicted within maximum 0.05mm deformation. Finally in consideration of these results, 2 and 4 cavities molds were designed and made and tested in injection molding process.

• The Korean Journal of Physiology and Pharmacology
• /
• v.10 no.5
• /
• pp.231-234
• /
• 2006

This study was designed to investigate the expression and production of interleukin-1beta $(IL-1{\beta})$ in human peripheral blood of trained runners and untrained controls after temporary moderate intensity exercise. Male long-distance trained runners (TR) and untrained sedentary control subjects (SED) ran for 1 h at 70% of heart rate reserve (HRR). $IL-1{\beta}$ gene and protein expressions were significantly higher in TR than those with SED at all 3 intervals examined independently. Significant increases in total sweat volume and oral temperature were observed after exercise in both groups, however, there were some differences between the groups. We conclude, therefore, that sweating due to exercise is associated with increase of $IL-1{\beta}$ and it is correlated with decrease of oral temperature.

• Journal of Korea Foundry Society
• /
• v.20 no.2
• /
• pp.97-103
• /
• 2000

In this study, a design of experiment, Taguchi method, was applied to optimize gating system design of escalator step die casting parts. Six shape factors which affect filling sequence of melt are adopted and divided into two levels respectively. Initial feeding differences of melt which were calculated by using S/N(signal-to-noise) ratio in each condition were demonstrated with the simulation of Flow-3D software program. Variations of S/N ratio according to shape factors were obtained and the optimal condition of gating system could also be obtained. It could be found that width of gate, contact angle of gate, thickness of runner are more effective factors on the filling sequence of melt than the others in this case of escalator step die casting parts. It showed that the economical gating system and sound filling sequence of melt were obtained by using Taguchi method.