• Elastomers and Composites
• /
• v.42 no.2
• /
• pp.112-118
• /
• 2007

An HRP immobilized carbon paste electrode, which was bound by EPDM, was newly fabricated and its electrochemical properties were investigated for the purpose of validating the new possibility for the practical use of biosensor. In the experimental range of substrate concentration, Lineweaver-Burk plot of the signal showed a good linearity. This means that HRP was embedded effectively to preserve its identity in the bulk of composite electrode materials and EPDM is a recommendatory binder. When the electrode was run at low operating potential($0.0\sim-1.0$ V vs. Ag/AgCl), it showed a high sensitivity and a good reproducibility. Especially the mechanical stability of the dried rubber was a remarkable breakthrough to get over a difficulty in putting the carbon-paste electrode bound with silicon oil to real use.

• Journal of Environmental Health Sciences
• /
• v.31 no.1
• /
• pp.86-93
• /
• 2005

Because generally large amount of sludges are generated from the process of sewage and wastewater treatment, the management and controlment of those sludge has become a important issue in many researches. In this dissertation, we conducted the research to see the physico-chemical characteristics of sludges generated from various sources. Moisture of sludges were 81.5% in textile industries, 81.4% in frame metal industries, 80.7% in 1st metal industries. Volatile solid were 22.1% in hide · rubber industries, 21.9% in coke · petroleum industries. Fixed solid were 18.5% and 17.7% in the 1st metal industries and frame metal industries. High heating value by wet base were 1,850 kcal/kg in coke · petroleum industries, 1,220 kcal/kg in hide · rubber industries, but sludges from the 1st metal industries and frame metal industries were impossible to incinerate because most of those sludges were inorganic. The leaching test showed that hazardous materials was detected in nearly every kinds of sludges. Some of sludges from hide · rubber industries and frame metal industries exceeded the leaching criteria and so they were classified as specific wastes. And other sludges generated in sewage treatment plants or other industries was below the leaching criteria.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.12
• /
• pp.1161-1170
• /
• 2014

Delta sash is an important part of automobile door, which has the functions of supporting and guiding seesaw of car's window, preventing dust and air from outside. In previous manufacturing process, each part of the delta sash was independently formed by tandem processes, and rubber is bonded to steel by poisonous glue. So, the previous processes, including roll forming process and toxic gases, had low production rate and high failure rate. In this study, progressive process design of the delta sash was proposed in order to increase productivity and high utilization of the materials. And instead of the poisonous glue used for adhesion of rubber in the previous tandem process, embossing and piercing processes were designed in the new guide to help the rubber to adhere well to steel. And the optimal piercing distance was designed to ensure structural safety, and prototypes were manufactured for verifying reliability of the processes.

• Transactions of Materials Processing
• /
• v.12 no.8
• /
• pp.724-729
• /
• 2003

In order to study the shearing characteristic of anti-vibration sheet metal which is used to reduce vibration noise, a blanking die was manufactured to blank a workpiece. The variables employed in this study were clearance, type of stripper plate, position of the rubber layer and type of the die design. These variables were used to study the effects on burr height, blank diameter and camber height. In the case of burr height from experimental investigation, the push-back die, combined with a movable stripper plate, showed greater burr height. The rubber-top position of a workpiece resulted in better qualities regardless of working variables. In the comparison of diameter measurement, the use of the push-back die with a fixed stripper plate, with a 4.5% clearance, showed better accuracy. For comparing camber height, the push-back die resulted in less cambering than the drop-through die. Also, the larger the clearance, the greater was the camber height. Considering experimental results, the shearing of anti-vibrational sheet metal is best achieved when the rubber layer is laying on the top, blanked with a fixed stripper plate in a push-back die, with a 4.5％ clearance.

• Composites Research
• /
• v.23 no.5
• /
• pp.1-7
• /
• 2010

To increase the adhesive strength of acrylonitrile butadiene rubber(NBR) and steel plate, the atmospheric pressure flame plasma(APFP) treatment device is applied. The effect of various conditions(processing velocity and distance) is experimentally investigated to ascertain the optimum conditions to yield the best adhesive properties. It is found that the optimum distance between burner port and steel plate is 40mm and the optimum processing velocity is 50m/min at given condition. When the surface is coated twice with the bonding agent, the adhesion strength of APFP treated steel plate is increased to about 20.5%. It suggests that the surface modification of steel by flame plasma treatment at atmospheric pressure is a proper and applicable method to improve the adhesion strength between steel and rubber.

• Korean Journal of Veterinary Service
• /
• v.41 no.2
• /
• pp.125-131
• /
• 2018

This study investigated the effects of the alkaline detergent and acid rinse used for cleaning milking machines on the rubber composition of the newly-developed teat cup liners. The samples prepared for use in the clean-in-place process were analyzed by ultraviolet spectrophotometer, ion chromatography and liquid chromatography. In the absorption spectrum of the first sample solution, the form of absorbance or absorption peak was largely different, compared to the absorption spectrum of alkaline detergent alone, but in the absorption spectra of the second and third sample solutions, the absorbance decreased, which was similar to the absorption spectrum in the pure acid detergent. In the ion chromatogram, two main peaks only, which might be shown by the pure alkaline detergent alone, were measured. In the liquid chromatograms, however, new peaks were observed in addition to the two main peaks caused by the pure alkaline detergent alone, which suggested that various molecular materials were created or eluted from the liner by the reaction with the alkaline detergent, but when washed with the acid detergent, any ion species were not produced. Therefore, we propose that an acid rinse should be applied, after cleaning the milking machine with the alkaline detergent.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.15 no.12
• /
• pp.1079-1084
• /
• 2002

Because complex insulation method is used in EHV(extra high voltage) insulation systems, macro Interfaces between two different bulk materials which affect the stability of insulation system exist inevitably. Interface between toughened epoxy and silicone rubber was selected as a interface in EHV insulation systems and tested AC interfacial breakdown properties with variation of many conditions to influence on electrical Properties, such as interfacial pressure, roughness and oil. Specimen was designed to reduce the effect of charge transport from electrode in the process of breakdown and to have the tangential electrical potential with the direction of the interface between epoxy and silicone rubber by using FEM(finite elements method). It could control the interfacial pressure, roughness and viscosity of oil. From the result of this study, it was shown that the interfacial breakdown voltage is improved by increasing interfacial Pressure and oil. In particular, the dielectric strength saturates at certain interracial Pressure level. The decreasing ratio of the interfacial breakdown voltage in non-oiled specimen was increased by the temperature rising, while oiled specimen was not affected by temperature.

• Elastomers and Composites
• /
• v.43 no.2
• /
• pp.63-71
• /
• 2008

Up to now, most of researches and practical applications of polymeric elastomers have been focused on rubber, a type of elastomeric materials. Therefore, it has been widely accepted that rubber industry is tire industry. In this review, we would like to illuminate new emerging technologies of elastomers. Among many examples, there are actuators which can transform their mechanical shapes with respect to the surrounding environments. Paper folding (so called "origami" in Japanese) technology can be another good example. Utilizing paper folding technology, three-dimensional (3D) architectures containing multi-functions can be constructed from programmed 2D structures. Elastomer microlens can also be fabricated using lithography technologies combined with chemical reactions.

• Elastomers and Composites
• /
• v.20 no.2
• /
• pp.115-131
• /
• 1985

Heavy residual fuel oils is a mixture of reduced crude from crude unit, bottom products from vacuum and/or catalytic cracking unit with distillate to meet the specification and generally used as heavy fuel oil for large combustion engines, boilers, etc$\cdots$. But this study was made to investigate heavy residual fuel oils for using as industrial raw material and resulted the following possiblities as valuable raw material as well as heavy fuel oil. 1) Production of straight asphalt through vacuum distillation unit. 2) Using straight asphalt from vacuum distillation unit for manufacturing of blown asphalts, cut back asphalts, emulsified asphalts and asphalt compound, rubber/asphalt sheet, etc$\cdots$. 3) Using waxy oil side streams for manufacturing of raw oil to be lube oil base stocks through solvent dewaxing. 4) Production of lube base oils and rubber process oils from dewaxed raw oil through chemical treatments. 5) Manufacturing of paraffine wax from slack wax to be produced as by product of dewaxing process.

• Journal of Environmental Science International
• /
• v.14 no.6
• /
• pp.521-524
• /
• 2005

We introduce a simplified crossing wood drain disperses rain water concentration and is used to protect the road surface from erosion due to flooding over the unpaved road. The efficiency of a simplified crossing wood drain was also investigated. A structure of simplified crossing wood drain can be produced within 10 minutes and installed within 18 minutes. The cost of the this product is 1/5 of that of the existing crossing drain product. The production and installation cost can be reduced according to dexterity. In the context of such applications, the degrees of damage for a rubber pad, which preventing the rain overflow, were varied according to their materials. A type of 8.2mm thick fabric rubber was the most suitable in this study.