• Bulletin of the Society of Naval Architects of Korea
• /
• v.6 no.1
• /
• pp.25-34
• /
• 1969

From viewpoints of over-all ship economy the straight framed V-bottom hull forms with chines are considered to be attractive even for usual commercial vessels, because increments of resistance over that of round hull forms, if any, can be well compensated with reduction in construction cost.[1] To investigate the influences of both prismatic coefficient and chine elevation on resistance performance, three models of straight-framed V-bottom hull forms which are similar to Prof. C. Ridgely-Nevitt's W-18, W-8, and W-20[2],[3] in size and hull form coefficients were tested at the SNU Ship Model Towing Tank for resistance measurements. They are of Cp=0.60, 0.65 and 0.70 and of ${\Delta}/(0.01L)^3=300$. Influence of variation of chine elevation on resistance performance were observed with the test results obtained at normal condition, and at the trimed by the stern by 2% and 4% of $L_{bp}$ at normal condition under same displacement. The hull form characteristics are shown in Table 1, and in Fig. 1, 2, 3, 4 and 5. The test results are shown in Fig 8, 9 and 10 in the form of Cr vs. $V/\sqrt{L}$ curves taking Cp as a parameter for normal condition, trim by the stern in 2% and 4% $L_{bp}$ at normal condition , respectively. Cr vs. $V/\sqrt{L}$ curves taking trim condition as a parameter are also shown in Fig 11, 12 and 13 for Cp=0.60 and 0.70, respectively. The best and the worst trim condition at given $V/\sqrt{L}$ in viewpoint of Cr are plotted for each Cp-value as shown in Fig 14, 15 and 16. From the above results the following conclusions are derived: (1) In general, the resistance performance of the straight-framed V-bottom hull forms are not inferior to those of round hull forms. At a certain range of $V/\sqrt{L}$ the former gives less resistance than the latter. (2) Regarding influences of Cp on Cr, it is observed that, at $V/\sqrt{L}$ less than about 0.925, the greater Cp-value gives the more increment of Cr, and that, at $V/\sqrt{L}$ greater than about 0.925 the smaller Cp-value gives the more increment of Cr. It is also noteworthy that the model of Cp=0.70 has remarkable hump on Cr vs. $V/\sqrt{L}$ curve between $V/\sqrt{L}=0.80$ and 0.90. (3) For higher speed within the test range, the chine elevation having the steeper slope around bow and the easier slope around amidship and stern, refered to watering, give the better results in resistance performance. (4) Assuming the chine elevations adopted for the tested models were not of the best, we would expect further improvement of resistance performance for such form. Hence, a systematic study on chine elevation is very disirable to prepare design data of general purpose for the such hull forms.

• Journal of Chest Surgery
• /
• v.12 no.4
• /
• pp.324-335
• /
• 1979

During the period of 4 years from August 1975 to August 1979 one hundred and forty seven cases of lung cancer were seen at Paik Foundation Hospital in Seoul, Korea. Among these 147 cases, 104 patients had primary carcinoma of the lung and the remainder was metastatic carcinoma to the lung. Among these 104 primary carcinoma patients, 73 cases were proven histologically as primary carcinoma of the lung. There were three cases of alveolar cell carcinoma [Table 1 ]. This clinical observation is based on those 73 cases including three case reports of the alveolar cell carcinoma. 1. Peak incidence was observed in the 5th decade of life. Male to female ratio was 2 to 1 [Fig. 1]. 2. Pathological classifications were as follows: epidermoid carcinoma, 24 cases [32.9%]; undifferentiated carcinoma, 20 cases [27.4%]; adenocarcinoma, 15 cases [20.5%]; bronchioloalveolar carcinoma [5.5%] and positive cytology, 10 cases [13.7%] [Fig. 2]. 3. Evidence of inoperability was observed in 55 patients [75% of the 73 cases] [Table 3]. 4. Among those 73 cases, operability was evaluated in 18 patients or 25%. One patient refused operation and 17 patients [23.6%] were explored. In 11 [15%] out of 17 patients, thoracotomies were performed. Six cases were pneumonectomies and 5 cases were lobectomies or bilobectomies [Fig. 3]. 5. First case of alveolar cell carcinoma was a 46 year-old housewife complaining of cough and hemoptysis for one year. The plain chest X-ray and bronchogram showed characteristic pictures as Figures 4 and 5. A pneumonectomy was carried out. Histologically, a beautiful alveolar carcinoma consisted of the characteristic tall columnar epithelial cells, which were lining the alveolar spaces as seen in Figures 6, 7, 8, and 20. 6. In the second case of 41 year old male, predominant clinical feature was single, well defined mass in the right lower lobe [Fig. 10 and 11] on chest X-ray. Bilobectomized specimen showed fragile, soft and hard tissue containing mucoid secretions and focal yellowish necrosis with pigmentation on cut surface [Fig. 12]. Slides showed tumor cells lined up along the alveolar septa with papillary projections [Fig. 13 and 14]. 7. Third case of alveolar cell carcinoma was a 50-year-old housewife with hemoptysis. An outstanding clinical picture was a round to lobulated mass in the right upper lobe [Fig. 16]. She is living now, 2 years and 1 month post-operatively, but has arrived at terminal stage with military nodular disseminations to the contralateral lung [Fig. 19].

• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.49 no.1
• /
• pp.39-45
• /
• 2012

In this paper, a distributed 2-hop routing algorithm is proposed. The main purpose of the proposed algorithm is to reduce the overall power consumption of each sensor node so that the lifetime of WSN(wireless sensor network) is prolonged. At the beginning of each round, the base station transmits a synchronization signal that contains information on the priority table that is used to decide whether each sensor node is elected as a cluster head or not. The priority table is constructed so that sensor nodes closer to half energy distance from the base station get the higher priority. 2-hop routing is done as follows. Cluster heads inside half energy distance from the base station communicate with the base station directly. Those outside half energy distance have to decide whether they choose 2-hop routing or 1-hop routing. To do this, each cluster head outside half energy distance calculates the energy consumption needed to communicate with the base station via 1-level cluster head or directly. If less energy is needed when passing through the 1-level cluster head, 2-hop routing is chosen and if not, 1-hop routing is chosen. After routing is done each sensor nodes start sensing data.

• Journal of Korean Society of Rural Planning
• /
• v.19 no.3
• /
• pp.13-24
• /
• 2013

With the increase of visitors to rural tourism villages, the direct selling at sites is getting vitalized. Accordingly, their display stores is getting more important. Therefore, this study has selected 30 domestic rural tourism villages as study objects for the attitude survey of 200 farming suppliers and the site examination for the designs of those display stores in order to analyze their status and classify the types of necessity. Such operation status as sale item, sale method, method of supply and demand, major customer, sales scale, manager, opening hour, and operation cost were examined, to identity and for design factors the pattern, material quality and color were investigated. For the attitude of farming suppliers, the tactics of sales, the reason for being positive or negative, the functionality and the features of display stores were examined through brainstorming. IBM SPSS Statistics 20 Program was employed for Frequency, which indicated that village chiefs and store managers with the sales scale of 1 to 20 million won are dealing with female customers in their 40's and 50's and that those stores are open at the time of experience or year round without any operation expense. Permanent type and Fixed type were found to be the design factors of the display-case type with the material and the color of wood and orange respectively. The result of investigation analysis of farming suppliers' attitude showed the followings: the need of display stores is quite high, structure type and permanent type have high fitness and from the viewpoint of display-on-table type as a standard moving type was very convenient. The analysis of significant items at the characteristics of those display stores revealed that their locations, quality conservation, sanitation, users' convenience, designs and promotion are very important. The result of status analysis revealed that though there is a correlation among the types of display stores depending on the visiting season of tourists their installing is not desirable. Three types have been analyzed: Type 1 is a structure type only in the villages with continuous visitors, Type 2 a moving-table type only in the villages with temporary visitors and Type 3 is a fixed display-case type.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.7 s.361
• /
• pp.71-80
• /
• 2007

This paper describes an efficient hardware design of WiBro security processor (WBSec) supporting for the security sub-layer of WiBro wireless internet system. The WBSec processor, which is based on AES (Advanced Encryption Standard) block cipher algorithm, performs data oncryption/decryption, authentication/integrity, and key encryption/decryption for packet data protection of wireless network. It carries out the modes of ECB, CTR, CBC, CCM and key wrap/unwrap with two AES cores working in parallel. In order to achieve an area-efficient implementation, two design techniques are considered; First, round transformation block within AES core is designed using a shared structure for encryption/decryption. Secondly, SubByte/InvSubByte blocks that require the largest hardware in AES core are implemented using field transformation technique. It results that the gate count of WBSec is reduced by about 25% compared with conventional LUT (Look-Up Table)-based design. The WBSec processor designed in Verilog-HDL has about 22,350 gates, and the estimated throughput is about 16-Mbps at key wrap mode and maximum 213-Mbps at CCM mode, thus it can be used for hardware design of WiBro security system.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.30 no.1
• /
• pp.21-26
• /
• 2020

This article reports the result on the spectroscopic analysis of the three Lightbox CVD-grown diamonds. Lightbox Jewelry, a De Beers company, has begun selling CVD laboratory-grown diamonds since September 2018. Recently, we had the opportunity to examine three Lightbox's pendant necklaces. The 0.25 ct, 0.25 ct, and 0.26 ct round brilliant were graded as "H" near colorless, Fancy Vivid orangy pink, and Fancy Vivid blue with cut grades of excellent, respectively. The laser-inscribed Lightbox logo under the table, large enough to be easily visible with a microscope. Based on the spectroscopic techniques, for near colorless sample was not subjected to post-growth HPHT processing to improve its color. For pink sample, optical centers at H3, 3H, 594 nm, NV, and GR1 were recorded. It was speculated that the pink sample have been received irradiation and annealing. In addition, the blue CVD synthetic sample was concluded to be irradiated without annealing.

• Journal of Korean Library and Information Science Society
• /
• v.32 no.2
• /
• pp.21-57
• /
• 2001

During the ASEM(Asian-Europe Meeting) the president Kim Dae-jung have a conference with France president Jacques Chirac about the Waikyujanggak book restitution which the president Mitterand promised in 1993. The results of conference, equivalence of quality and quantity, have stirred up Korean public sentiment. The restitution of cultural asset is a very subtile problem in all of the country. The united Germany and from the Soviet Union dismantled Russia also have begun to discuss the library book restitution. These two countries had plundered library books each other during the World War II. To resolve the issue Germany and Russia are having several Round Table at governmental level and library expert level. However except Lituania and Georgia three are not many successful outcomes. This study based on the process of the book restitution the Germany and Russia being under way. Though our historical background is different from these two countries, we have a same problem.

• Korea journal of population studies
• /
• v.12 no.1
• /
• pp.19-29
• /
• 1989

It is well known that vital statistics is of great importance as basic data for establishing various range of national policies. Especially, vital statistics is important among demographic information for monitoring and evaluating the population policy, for constructing life table, for making population projection, and for studying various aspects of the society. In principle, the production of vital statistics is based on the registration system. It is, however, still observed that there are some limitations in utilizing fully the registration system due to the inherent problems such as problems in its coverage, accuracies and timeliness. Thus, as an alternative, many countries conduct survey on vital statistics in order to supplement the registration system and obtain in-depth data. Korea is no exception in this aspect. The National Bureau of Statistics carries out the so-called Continuous Demographic Survey. This is a kind of multi-round retrospective survey, covering 32, 000 households and having reference period of one month. The survey has also characteristics of multi-subject sample. Thus, surveys on economic activity status of population, house-hold income & expenditure, and social indicators are together conducted with the same sample. It is, however, found that the survey itself tends to have some quality problems. Especially, the quality problems connected with field data collection are summarized as coverage error, non-response error and response error. Although it is inevitable not to be free from these errors, we should make all our efforts to reduce the errors. The probable schemes pointed out in this paper are as follows : 1) the strengthening formal quality control activities, 2) the review of the survey method, i. e., the combining interview method with mail-sending and mail-back method or pick-up method, 3) well documentation for various cases found in every stage of data collection, and 4) the strengthening the analytical activities. It is, also, emphasized that sincerity of planners and interviewers is the most important factor among other things.

• Journal of Broadcast Engineering
• /
• v.25 no.1
• /
• pp.67-82
• /
• 2020

This study is based on the screen composition(shot size, split screen, candidate placement, lighting, stage) that fits the discussion process (round table, sitting, standing method) adopted from the 19th presidential candidates' TV joint discussion to analyze the adequacy and limitations of the methodology(design, candidate background, etc.). In addition, the progress and screen composition of the 45th US Presidential Candidates Debate in 2016 and the 25th Presidential Candidates of France TV Joint Debate in 2017 have been analyzed to compare and contrast the methods used in Korea. Through this, we apply the screening method to the 20th Presidential Candidate TV Joint Debate, which will be held in 2022, to fit the fixed discussion process that can fully identify candidates' qualities, policies, and vision.

• Restorative Dentistry and Endodontics
• /
• v.28 no.3
• /
• pp.203-208
• /
• 2003

The purpose of this study was to evaluate the effect of salivary contamination of teeth on bonding efficacy of self-priming and self-etching DBSs. The materials used were Single Bond(SB, self-priming system, 3M), Unifil Bond(UB, self-etching system, GC), and Scotchbond Multi-Purpose Plus(SM, 3M) as control. Forty five human molars randomly allocated to three groups as dentin bonding systems tested and embedded in epoxy resin. Then the specimens were wet-ground to expose flat buccal enamel surface or flat occlusal dentin surface and cut bucco-lingually to form two halves with slow speed diamond saw. One of them was used under non-contamination, other under contamination with saliva. The bonding procedure was according to the manufacturer's directions and resin composite(Z-100, 3M Dental Products, St. Paul, MN) was built-up on the bonded surface 5mm high. The specimens were ground carefully at the enamel-composite interface with fine finishing round diamond bur to create an hour-glass shape yielding bonded surface areas of $1.5{\pm}0.1\textrm{mm}^2$. The specimens were bonded to the modified microtensile testing apparatus with cyanoacrylate, attached to the universal testing machine and stressed in tension at a CHS of 1mm/min. The tensile force at failure was recorded and converted to a tensile stress(MPa). Mean values and standard deviations of the bond strength are listed in table. One-way ANOVA was used to determine significant difference at the 95% level. The bond strength of SBMP and SB were not affected by salivary contamination, but that of UB was significantly affected by salivary contamination. These results indicate that DBSs with total etch technique seems less likely affected by salivary contamination in bonding procedure.