• Journal of the Semiconductor & Display Technology
• /
• v.9 no.3
• /
• pp.53-58
• /
• 2010

In this study, we have investigated the effect of the ambient gases on the characteristics of IZO thin films for the OLED (organic light emitting diodes) devices. For this purpose, IZO thin films were deposited by RF magnetron sputtering under various ambient gases (Ar, $Ar+O_2$ and $Ar+H_2$) at $150^{\circ}C$. In order to investigate the influences of the oxygen and hydrogen, the flow rate of oxygen and hydrogen in argon mixing gas has been changed from 0.1sccm to 0.5sccm, respectively. All the samples show amorphous structure regardless of ambient gases. The electrical resistivity of IZO film increased with increasing flow rate of $O_2$ under $Ar+O_2$ while under $Ar+H_2$ atmosphere the electrical resistivity showed minimum value near 0.5sccm of $H_2$. All the films showed the average transmittance over 85% in the visible range. The OLED device was fabricated with different IZO substrates made by configuration of IZO/${\alpha}$-NPD/DPVB/$Alq_3$/LiF/Al to elucidate the performance of IZO substrate. OLED devices with the amorphous-IZO (a-IZO) anode film show better current densityvoltage-luminance characteristics than that of OLED devices with the commercial crystalline-ITO (c-ITO) anode film. It can be explained that very flat surface roughness and high work function of a-IZO anode film lead to more efficient hole injection by reduction of interface barrier height between anode and organic layers. This suggests that a-IZO film is a promising anode materials substituting conventional c-ITO anode in OLED devices.

• Journal of the Semiconductor & Display Technology
• /
• v.21 no.4
• /
• pp.138-143
• /
• 2022

We analyzed the influence of post-annealing on Ga₂O₃/n-type 4H-SiC heterojunction diode. Gallium oxide (Ga₂O₃) thin films were deposited by radio frequency (RF) sputtering. Post-deposition annealing at 950℃ in an Oxygen atmosphere was performed. The material properties of Ga₂O₃ and the electrical properties of the diodes were investigated. Atomic Force Microscopy (AFM), X-Ray Diffraction and Scanning Electron Microscope (SEM) images show a significant increase in the roughness and crystallinity of the O₂-annealed films. After Oxygen annealing X-ray Photoelectron Spectroscopy (XPS) shows that the atomic ratio of oxygen increases which is related to a decrease in oxygen vacancy within the Ga₂O₃ film. The O₂-annealed diodes exhibited higher on-current and lower leakage current. Moreover, the ideality factor, barrier height, and thermal activation energy were derived from the current-voltage curve by increasing the temperature from 298 - 434K.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2022.05a
• /
• pp.199-199
• /
• 2022

선행 연구들을 통해 미세지형이 유역에서의 유사 유출량에 영향을 끼침을 알 수 있다. 그러나 여전히 유사-유출에 대한 미세지형의 영향이 불분명하여 유역 내 토양 침식 과정에서 미세지형적 거칠기를 고려할 때 혼란이 야기될 수 있다. 따라서, 유사유출량과 토양침식량에 대한 보다 정확한 예측 및 산정을 위해 미세지형이 토양 침식에 미치는 영향을 명확하게 하는 것이 필요하다. 본 연구에서는 Hairsine-Rose 침식 모형과 동역학파(Dynamic wave) 모형을 사용하여 강우-유출에 따른 미세지형의 유사-유출 과정을 수치적으로 모의하였다. 모의 결과에 따르면, 미세지형은 동일 강우 및 유출 조건에서도 유역 내 유사 유출량을 변화시켰다. 또한, 본 연구의 모의조건 하에서 지반이 비교적 미세토사로 구성된 경우 미세지형이 거칠수록 침식률이 증가하는 반면 지반의 토사가 대부분 굵은 입경을 가질 때는 매끄러운 지형보다 거친 미세지형에서 토양 침식률이 감소함을 확인하였다. 따라서, 지형의 미세지형 변동 정도와 토양침식률 사이에 비례 또는 반비례 관계가 형성됨을 보이고, 이러한 관계를 형성하는 과정에 입경 분포가 미치는 영향을 제시하였다. 마지막으로, 본 연구 결과를 통해 장갑화(armoring) 과정이 입경 분포뿐만 아니라 미세지형의 거칠기에 따라 유역별로 다르게 나타나는 것을 확인하였다. 따라서 유사-유출에 대한 미세지형의 영향을 적절하게 고려하기 위해 부상(Pick-up), 이류 및 퇴적 등 입경 별 퇴적물 이동이 다중 물리적으로 고려되어야 한다는 점을 강조한다. 본 연구를 통해 지표면의 미세지형적 거칠기 및 토양 입경에 대한 정확한 정보가 필요함을 알 수 있으며, 이를 충분히 고려한다면 강우 유출에 의한 토양 침식 메커니즘에 대한 이해도와 토양침식량에 대한 정량적 예측의 정확도가 향상될 것으로 예상된다.

• Proceedings of the National Institute of Ecology of the Republic of Korea
• /
• v.4 no.4
• /
• pp.159-176
• /
• 2023

The conservation of the raccoon dog (Nyctereutes procyonoides) in South Korea requires the protection and preservation of natural habitats while additionally ensuring coexistence with human activities. Applying habitat map modeling techniques provides information regarding the distributional patterns of raccoon dogs and assists in the development of future conservation strategies. The purpose of this study is to generate potential habitat distribution maps for the raccoon dog in South Korea using geospatial technology-based models. These models include the frequency ratio (FR) as a bivariate statistical approach, the group method of data handling (GMDH) as a machine learning algorithm, and convolutional neural network (CNN) and long short-term memory (LSTM) as deep learning algorithms. Moreover, the imperialist competitive algorithm (ICA) is used to fine-tune the hyperparameters of the machine learning and deep learning models. Moreover, there are 14 habitat characteristics used for developing the models: elevation, slope, valley depth, topographic wetness index, terrain roughness index, slope height, surface area, slope length and steepness factor (LS factor), normalized difference vegetation index, normalized difference water index, distance to drainage, distance to roads, drainage density, and morphometric features. The accuracy of prediction is evaluated using the area under the receiver operating characteristic curve. The results indicate comparable performances of all models. However, the CNN demonstrates superior capacity for prediction, achieving accuracies of 76.3% and 75.7% for the training and validation processes, respectively. The maps of potential habitat distribution are generated for five different levels of potentiality: very low, low, moderate, high, and very high.

• Ocean Science Journal
• /
• v.40 no.1
• /
• pp.25-44
• /
• 2005

Long-term, continuous, and real-time ocean monitoring has been undertaken in order to evaluate various oceanographic phenomena and processes in the East/Japan Sea. Recent technical advances combined with our concerted efforts have allowed us to establish a real-time monitoring system and to accumulate considerable knowledge on what has been taking place in water properties, current systems, and circulation in the East Sea. We have obtained information on volume transport across the Korea Strait through cable voltage measurements and continuous temperature and salinity profile data from ARGO floats placed throughout entire East Sea since 1997. These ARGO float data have been utilized to estimate deep current, inertial kinetic energy, and changes in water mass, especially in the northern East Sea. We have also developed the East Sea Real-time Ocean Buoy (ESROB) in coastal regions and made continual improvements till it has evolved into the most up-to-date and effective monitoring system as a result of remarkable technical progress in data communication systems. Atmospheric and oceanic measurements by ESROB have contributed to the recognition of coastal wind variability, current fluctuations, and internal waves near and off the eastern coast of Korea. Long-tenn current meter moorings have been in operation since 1996 between Ulleungdo and Dokdo to monitor the interbasin deep water exchanges between the Japanese and Ulleung Basins. In addition, remotely sensed satellite data could facilitate the investigation of atmospheric and oceanic surface conditions such as sea surface temperature (SST), sea surface height, near-surface winds, oceanic color, surface roughness, and so on. These satellite data revealed surface frontal structures with a fairly good spatial resolution, seasonal cycle of SST, atmospheric wind forcing, geostrophic current anomalies, and biogeochemical processes associated with physical forcing and processes. Since the East Sea has been recognized as a natural laboratory for global oceanic changes and a clue to abrupt climate change, we aim at constructing a 4-D continuous real-time monitoring system, over a decade at least, using the most advanced techniques to understand a variety of oceanic processes in the East Sea.

• Journal of Korean Society for Geospatial Information Science
• /
• v.21 no.4
• /
• pp.65-71
• /
• 2013

Wind shear means the variation of wind speed according to the height. Wind shear is the important factor affecting the energy production of wind turbines. Power Law is used to extrapolate wind speed data. Normally, a Power Law exponent of 0.143 is used and this is referred to as the 1/7th Power Law. The Power Law exponent is affected by atmospheric stability and surface roughness of the site. Thus, it is necessary to calculate the Power Law exponent of the site exactly for an accurate estimation of wind energy. In this study, wind resources were measured at the three Met-masts which were located in the coastal area of northeastern Jeju Island. The Power Law exponents of the sites were calculated and proposed using measured data. They were 0.141 at Handong, 0.138 at Pyeongdae, and 0.1254 at Udo. We compared annual energy productions which are calculated using a Power Law exponent of 0.143, the proposed value of the Power Law exponents for each site, and the measured data. As a result, the cases of calculating using the proposed values were more similar to the cases using the measured data than the cases using the 0.143 value. Finally, we found that the propsed values of the Power Law exponent are available to more accurately estimate wind resources.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.12
• /
• pp.1805-1810
• /
• 2010

We present a simple, cost-effective, and fast fabrication process for three-dimensional (3D) microstructures; this process is based on multi-step electrochemical etching of metal foils which facilitates the mass production of 3D microstructures. Compared to electroplating, this process maintains uniform and well-controlled material properties of the microstructure. In the experimental study, we perform single-step electrochemical etching of aluminum foils for the fabrication of 2D cantilever arrays. In the single-step etching, the depth etch rate and bias etch rate are measured as $1.50{\pm}0.10 {\mu}m/min$ and $0.77{\pm}0.03 {\mu}m/min$, respectively. Using the results of single-step etching, we perform two-step electrochemical etching for 3D microstructures with probe tips on cantilevers. The errors in height and lateral fabrication in the case of the fabricated structures are $15.5{\pm}5.8% $ and $3.3{\pm}0.9%$, respectively; the surface roughness is $37.4{\pm}9.6nm$.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.18 no.2
• /
• pp.4116-4120
• /
• 1976

With the use of many rivers increased nearly to the capacity, the need for information concerning daily quantities of water and the total annual or seasonal runoff has became increased. A systematic record of the flow of a river is commonly made in terms of the mean daily discharge Since. a single observation of stage is converted into discharge by means of rating curve, it is essential that the stage discharge relations shall be accurately established. All rating curves have the looping effect due chiefly to channel storage and variation in surface slope. Loop rating curves are most characteristic on streams with somewhat flatter gradients and more constricted channels. The great majority of gauge readings are taken by unskilled observers once a day without any indication of whether the stage is rising or falling. Therefore, normal rating curves shall show one discharge for one gauge height, regardless of falling or rising stage. The above reasons call for the correction of the discharge measurements taken on either side of flood waves to the theoretical steady-state condition. The correction of the discharge measurement is to consider channel storage and variation in surface slope. (1) Channel storage As the surface elevation of a river rises, water is temporarily stored in the river channel. There fore, the actual discharge at the control section can be attained by substracting the rate of change of storage from the measured discharge. (2) Variation in surface slope From the Manning equation, the steady state discharge Q in a channel of given roughness and cross-section, is given as {{{{Q PROPTO SQRT { 1} }}}} When the slope is not equal, the actual discharge will be {{{{ { Q}_{r CDOT f } PROPTO SQRT { 1 +- TRIANGLE I} CDOT TRIANGLE I }}}} may be expressed in the form of {{{{ TRIANGLE I= { dh/dt} over {c } }}}} and the celerity is approximately equal to 1.3 times the mean watrr velocity. Therefore, The steady-state discharge can be estimated from the following equation. {{{{Q= { { Q}_{r CDOT f } } over { SQRT { (1 +- { A CDOT dh/dt} over {1.3 { Q}_{r CDOT f }I } )} } }}}} If a sufficient number of observations are available, an alternative procedure can be applied. A rating curve may be drawn as a median line through the uncorrected values. The values of {{{{ { 1} over {cI } }}}} can be yielded from the measured quantities of Qr$.$f and dh/dt by use of Eq. (7) and (8). From the 1/cI v. stage relationship, new vlues of 1/cI are obtained and inserted in Eq. (7) and (8) to yield the steady-state discharge Q. The new values of Q are then plotted against stage as the corrected steadystate curve.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.15 no.4
• /
• pp.431-442
• /
• 2013

Most of previous studies have insufficiently investigated the shear behavior and fracturing characteristics, experimentally in respect to the change of size of tooth-shaped surface asperity such as length and slope angle in a broad range. This study investigates the influence of the length and slope angle of a tooth-shaped surface asperity on the fracturing characteristics and the interface shear strength by using direct shear test apparatus. A total of 36 interface direct shear tests were conducted by changing the three types of slope angle of surface asperity, four type of length, and three types of normal stress. The shape of fractured surface after the test was quantified by using a three-dimensional surface roughness measurement apparatus. Through the experimental test results, the characteristics of fractured shape of surface asperity according to the normal stress were investigated. In addition, fractured length and height were quantified at each slope angle of surface asperity under a certain normal stress condition.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.2
• /
• pp.231-243
• /
• 2016

This study presents the applicability of two-dimensional (2D) flood inundation model by applying to real irrigation reservoir failure with limited available data. The study area is Sandae Reservoir placed in Gyeongju and downstream area of it and the reservoir was failured by piping in 2013. The breach hydrograph was estimated from one-dimensional (1D) hydrodynamic model and the discharge was employed for upstream boundary of 2D flood inundation model. Topography of study area was generated by integrating digital contour map and satellite data, and Cartesian grids with 3m resolution to consider geometry of building, road and public stadium were used for 2D flood inundation analysis. The model validation was carried out by comparing predictions with field survey data including reservoir breach outflow, flood extent, flood height and arrival time, and identifying rational ranges with allowed error. In addition, the applicability of 2D model is examined using different simulation conditions involving grid size, building and roughness coefficient. This study is expected to contributed to analysis of irrigation reservoirs were at risk of a failure and setting up Emergency Action Plan (EAP) against irrigation reservoir failure.