• 멤브레인
• /
• 제13권2호
• /
• pp.88-100
• /
• 2003

테일러 와류흐름 여과에서 평균기공 1.2 ${\mu}m$인 셀룰로우스 에스테르 정밀막으로 이루어진 내부원통의 회전속도와 슬러리의 농도, 입자의 크기에 따른 여과선속의 변화를 실험을 통하여 알아보았다. 여과선속은 압력차에 비례하고 저항에 반비례하였으며, 시간에 따른 케이크 층의 저항 변화를 회전속도, 슬러리의 농도, 입자의 크기에 따라 검토하였다. 회전속도가 증가할수록 케이크 저항이 감소하고 짧은 시간에 준정상 상태에 도달하였다 슬러리의 농도를 증가시킬수록 초기 저항이 급격히 증가하였고 높은 저항값에서 준정상 상태가 유지되었으나, 준정상 상태에 도달하는 시간은 농도에 무관하였다. 입자 크기가 작을 때 저항이 크게 나타남을 관찰하였는데, 입자 크기가 작을수록 막 기공을 막을 확률이 더 높고 전단력에 의해 영향을 덜 받기 때문이라 생각할 수 있다. 본 연구에서 제안한 모델식은 입자의 퇴적과 제거항으로 나누어져 있는데, 실험상수의 평균값을 사용하여 실험결과와 잘 일치하였다.

• 한국자동차공학회논문집
• /
• 제19권3호
• /
• pp.65-72
• /
• 2011

In this study, the numbers, sizes of particles from a single cylinder direct injection spark-ignition (DISI) engine fuelled with gasoline and LPG are examined over a wide range of engine operating conditions. Tests are conducted with various engine loads (2~10bar of IMEP) and fuel injection pressures (60, 90, and 120 bar) at the engine speed of 1,500 rpm. Particles are sampled directly from the exhaust pipe using rotating disk thermodiluter. The size distributions are measured using a scanning mobility particle sizer (SMPS) and the particle number concentrations are measured using a condensation particle counter (CPC). The results show that maximum brake torque (MBT) timing for LPG fuel is less sensitive to engine load and its combustion stability is also better than that for gasoline fuel. The total particle number concentration for LPG was lower by a factor of 100 compared to the results of gasoline emission due to the good vaporization characteristic of LPG. Test result presents that LPG for direct injection spark ignition engine help the particle emission level to reduce.

• 한국해양공학회지
• /
• 제25권5호
• /
• pp.15-20
• /
• 2011

This study carried out a series of experiments involving impact tests (Drop Weight type & Charpy type with a standard specimen and newly designed I-type specimen), hardness tests, and fracture surface observations of French-made roll shell steel (F), abnormal roll shell steel (M), reheated roll shell steel (R), and S25C steel under heat treatment conditiAn experimental study was carried out to study the solid-liquid mixture upward hydraulic transport of solid particles in vertical and inclined annuli with a rotating inner cylinder. The lift forces acting on a fluidized particle play a central role in many important applications such as the removal of drill cuttings in horizontal drill holes, sand transport in fractured reservoirs, sediment transport, the cleaning of particles from surfaces, etc. In this study a clear acrylic pipe was used to observe the movement of solid particles. Annular velocities varied from 0.4 to 1.2 m/s. The effect of the annulus inclination and drill pipe rotation on the carrying capacity of a drilling fluid, particle rising velocity, and pressure drop in a slim hole annulus were measured for fully-developed flows of water and aqueous solutions of CMC (sodium carboxymethyl cellulose) and bentonite. The rotation of the inner cylinder was efficient at carrying particles to some degree. For a higher particle volume concentration, the hydraulic pressure loss of the mixture flow increased because of the friction between the wall and solids or between solids.

• 한국유체기계학회 논문집
• /
• 제15권3호
• /
• pp.12-18
• /
• 2012

The Lattice Boltzmann Method has developed for solving the Boltzmann equation in Cartesian domains containing immersed boundaries of arbitrary geometrical complexity moving with prescribed kinematics. When a immersed boundaries are sweeping the fixed fluid node, refilling the node information in a vicinity of fluid nodes is one of the important issues in Lattice Boltzmann Method. In this study, we propose a simple refill algorithm for the particle distribution function based on a proper velocity, density and strain rate to enhance accuracy and stability of the method. The refill scheme based on a asymptotic analysis of LBGK model has improved accuracy than interpolation schemes. The proposed scheme in this study is validated by the simulations of an impulsively started rotating circular cylinder to investigate adaptability for fluid-structure interaction (FSI) problem. This refill scheme has improved stability and accuracy especially at high Reynolds number region.

• 대한기계학회논문집B
• /
• 제36권10호
• /
• pp.1011-1017
• /
• 2012

본 논문에서는 롤타입 마스크를 사용한 마이크로/나노 구조 제작용 광학 리소그래피 방법을 소개한다. 이 생산 방법은 다양한 목표 해상도에 따라 위상지연 리소그래피방법과 포토리소그래피로 나뉜다. 사용되는 빛의 파장대보다 작은 해상도를 갖는 패턴을 제작하기 위해서 실린더 형태의 위상지연 마스크를 활용한 근거리 노광 방식을 사용한다. 또한 필름 형태의 금속 마스크를 써서 포토리소그래피를 연속방식으로 수행하였는데 이 방식은 실린더 마스크의 회전수를 조절함으로써 노광 결과 패턴의 주기를 실시간으로 조절할 수 있다. 이 기술의 응용으로 금속 그물패턴으로 만들어진 100 $mm^2$ 넓이의 투명전극을 제작하였다.

• Tribology and Lubricants
• /
• 제25권6호
• /
• pp.409-413
• /
• 2009

This paper presents the hardness and friction characteristics of pb-free pin-bush bearing metal, which is manufactured by a centrifugal casting technology. A bronze metal with a high hardness and low friction properties is usually used for Diesel engine pin-bush bearing and high pressure cylinder. Pb-free metal for pin-bush bearings shows a little high hardness of 120 Hv compared with that of a conventional Pb bearing metal of 100~110 Hv. In general, the friction coefficient of pin-bush bearings is affected by a rotating speed and a load for various rubbing contact modes. But a contact load is more influential parameter when the contact rubbing mode transits from a mixed lubrication to a dry friction contact. The experimental result shows that the friction coefficient is more unstable at the dry contact mode compared with that of other two rubbing modes such as oil film contact and mixed friction conditions.

• 한국수산과학회지
• /
• 제22권6호
• /
• pp.415-423
• /
• 1990

In a laboratory model the response of the boundary layer flow over topography is studied in a rotating sliced cylinder by employing the source-sink analogy with Ekman layer dynamics. The boundary layer flow is produced by two different fluid. In the first experiment homogeneous fluid is used both for the source and the working fluid of the container. In the second experiment a denser fluid is used for the source with the same working fluid. For the homogeneous western boundary layer flow both the northward and the southward flow were affected by the topography(ridge) to produce a cyclonic motion near the ridge. When woughward moving heavy boundary flow of slower speed and the northward moving faster flow were present at the same time, the splitting of southward flow and the separating of the northward flow were observed with a cyclonic motion at the ridge. The most important factor that influence production of the cyclonic motion has been turned out to be the presence of the topography in the western boundary layer. In particular the role of the southward moving heavy flow over the interior flow pattern was found to be very significant.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2008년도 춘계학술대회논문집
• /
• pp.801-806
• /
• 2008

Large quantity of bending deformation as well as rotating torque fluctuation at the balance shaft are main struggles during the operation in a high speed rotation and thereby, two issues should be cleared at the design process of balance shaft module. Since two issues are highly related with balance shaft itself and particularly much sensitive to the location of both supporting bearing and unbalance mass, the design strategy on balance shaft should be investigated at the aspect of controlling two critical issues at the early stage of balance shaft design. To tackle two main problems, the formulation of objective function that minimizes critical issues, both bending deformation as well as torque fluctuation, is suggested to derive the optimal information on balance shaft. Then, optimal informations are reviewed at the practical logics and the guideline at the selection of locations, both supporting bearing and unbalance mass, is addressed at the final chapter.

• Tribology and Lubricants
• /
• 제30권2호
• /
• pp.116-123
• /
• 2014

The objective of this study is to model and simulate the nonlinear lubrication performance of the sliding part between the piston and cylinder wall in a hydrostatic swash-plate-type axial piston pump. A numerical algorithm is developed that facilitates simultaneous calculation of the rotating body motion and fluid film pressure to observe the fluid film geometry and power loss. It is assumed that solid asperity contact, so-called mixed lubrication in this study, invariably occurs in the swash-plate-type axial piston pump, which produces a higher lateral moment on the pistons than other types of hydrostatic machines. Two comparative mixed lubrication models, rigid and elastic, are used to determine the reaction force and sliding friction. The rigid model does not allow any elastic deformation in the partial lubrication area. The patch shapes, reactive forces, and virtual local elastic deformation in the partial lubrication area are obtained in the elastic contact model using a simple Hertz contact theory. The calculation results show that a higher reaction force and friction loss are obtained in the rigid model, indicating that solid deformation is a significant factor on the lubrication characteristics of the reciprocating piston part.

• 한국정밀공학회지
• /
• 제16권6호
• /
• pp.58-65
• /
• 1999

The spinning machine has been developed for a bus and truck wheel disc which is manufactured by spinning process method. This machine has the mechanical structure with bed, 2-column, cross head, 2-vertical slide, 2-horizontal slide with forming roller, clamp slide and main spindle similar to large size vertical lathe. Main spindle attached the mandrel is rotated about 500rpm drived by 280kW power DC motor, and a rotating black material pressed on the mandrel with the clamp slide is spinformed by 2-forming rollers which are attached inner end of the 2-horizontal slides. The 2-vertical and 2-horizontal slides are actuated by the hydraulic cylinder which is controlled by the servo valve individially, and these servo valves are controlled by control signal of the CNC controller which is computed with position signal feedbacked from the encoder sensor. The developed machine can manufacture wheel disc of various section profile without mandrel change because section profile is easily modified using program editing in the CNC controller processor. The wheel disc manufactured by spinning process method has many advantages that the endurance is increased by 2 times and the weight is decreased by 30% compared with a conventional disc.