• Proceedings of the Korean Vacuum Society Conference
• /
• 2008.02a
• /
• pp.379-379
• /
• 2008

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.51 no.10
• /
• pp.477-482
• /
• 2002

One of the key technologic requirements for rotary blood pumps is the sealing of the motor shaft. A mechanical seal, a journal bearing, magnetic coupling, and magnetic suspension have been developed, but they have drawbacks such as wear, thrombus formation, and power consumption. A magnetic fluid seal is durable, simple, and non power consumptive. Long-term experiments confirmed these advantages. The seal body was composed of a Nd-Fe-B magnet and two pole pieces; the seal was formed by injecting magnetic fluid into the gap (50${\mu}m$) between the pole pieces and the motor shaft. To contain the ferro-fluid in the seal and to minimize the possibility of magnetic fluid making contact with blood, a shield with a small cavity was attached to the pole piece. While submerged in blood, the sealing pressure of the seal was measured and found to be 31kPa with magnetic fluid LS-40 (saturated magnetization, 24.3 KA/m) at a motor speed of 10,000 rpm and 53kPa under static conditions(0mmHg). The specially designed magnetic fluid seal for keeping liquids out is useful for axial flow blood pumps. The magnetic fluid seal was incorporated into an intra-cardiac axial flow blood pump.

• Transactions on Electrical and Electronic Materials
• /
• v.11 no.2
• /
• pp.65-68
• /
• 2010

The operation principle of a traveling wave rotary type ultrasonic motor can be successfully applied to the fluidic transfer mechanism of the micro-pump. This paper proposes an innovative valveless micro-pump type that uses an extensional vibration mode of a traveling wave as a volume transportation means. The proposed pump consists of coaxial cylindrical shells that join the piezoelectric ceramic ring and metal body, respectively. In order to confirm the actuation mechanism of the proposed pump model, a numerical simulation analysis was implemented. In accordance with the variations in the exciting wave mode and pump body dimension, we analyzed the vibration displacement characteristics of the proposed model, determined the optimal design condition, fabricated the prototype pump from the analysis results and evaluated its performance. The maximum flow rate was approximately $595\;{\mu}L/min$ and the highest back pressure was 0.88 kPa at an input voltage of $130\;V_{rms}$. We confirmed that the peristaltic motion of the piezoelectric actuator was effectively applied to the fluid transfer mechanism of the valveless type micro pump throughout this research.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.102-102
• /
• 2011

인공위성이 임무를 수행하는 우주환경은 지상 환경과 달리 고진공 및 극저온의 극한환경으로 지상에서는 제대로 작동하는 것으로 관찰되더라도 우주환경에서는 예상하지 못한 기능장애를 일으켜 위성의 성능에 치명적인 영향을 미치기도 한다. 이에 10-5 torr 이하의 고진공과 -180$^{\circ}C$ 이하의 극저온 환경을지상에서 모사하여 위성체의 안정성 및 신뢰성을 시험한다. 시험에는 열진공챔버라고 불리는 우주환경모사기가 사용이 되며, 기본적으로 챔버 내부 진공형성이 중요하다. 우주환경의 모사를 위해 먼저 저진공펌프로 10-2 Torr 의 저진공을 형성한 후 Turbo-molecular pump 및 Cryopump를 이용하여 10-5 Torr 이하의 고진공을 형성하게 된다. 본 논문에서는 기존 우주환경모사기에 부착된 oil type rotary pump 및 구형 turbo-molecular pump의 교체 과정을 기술한다. 특히, 저진공펌프의 경우는 챔버 내부로의 oil 역류로 인한 오염 문제를 방지하기 위하여 dry type의 펌프가 설치되었다.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2000.02a
• /
• pp.39-39
• /
• 2000

당사는 1996년 SPUTTERING SYSTEM 제작을 시작으로 하여 진공관련장치 및 부품을 제작, 납품하는 기업입니다. 그 동안 산업체 및 대학, 연구소 등에 제작 납품된 품목은 양산용SPUTTER 연구실험용SPUTTER, ION PLATING, RIE SYSTEM, E-BEAM 증착기 산업용 AL-EVAPORATOR, 산업용 AIP SYSTEM, 고온열처리로, 진공건조장치 진공 배기SYSTEM, 기타 진공관련장치가 있으며 진공부품으로는 OIL ROTARY PUMP, DIFFUSION PUMP, VALVE 및 배관부품 등이 있습니다. 그밖에 취급하는 품목으로는 진공게이지류 및 터보펌프를 판매하고 있습니다. 일부 장치는 기술력을 인정받아 일본, 동남아시아, 중국 등에 수출되었습니다. 당사는 항상 고객이 필요로 하는 진공응용장치를 다년간 축적된 제조기술과 연구력을 바탕으로 만족스러운 제품을 공급하고 있기에 이를 소개하고자 합니다.

• International Journal of Air-Conditioning and Refrigeration
• /
• v.16 no.3
• /
• pp.77-82
• /
• 2008

For heat pumps used in a cold region, it is very important to obtain appropriate heating capacity. Several studies using a variable speed compressor and an additional heater have been performed to enhance heating capacity at low ambient temperatures. However, for outdoor temperature conditions below $-15^{\circ}C$, it is still difficult to obtain enough heating capacity above the rated value. In recent studies, the application of gas injection technique into a two-stage heat pump yielded noticeable heating performance improvement at low temperature conditions. In this study, the heating performance of a two-stage gas injection heat pump with a rated capacity of 3.5 kW was measured and analyzed by varying refrigerant charge amount and EEV opening at the standard heating condition. The heating performance of the two-stage gas injection heat pump was compared with that of a two-stage non-injection heat pump. The heating capacity and COP of the two-stage gas injection heat pump were improved by 2-10% at the optimal charging condition over those of the two-stage non-injection heat pump.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.7
• /
• pp.1-7
• /
• 2014

A variable displacement vane pump is possible to improve the fuel economy by varying the pump capacity with a vane mechanism according to the engine operating speed range and reducing its driving torque. In general the experimental evaluation of the vane pump for the transmission has been performed mainly not with the vehicle or dynamometer test rig but with component test rig due to the implementation and safety problems. In this paper, in order to evaluate the performance of the developed vane pump as well as the compatibility with other rotary and hydraulic components of the target transmission, the transmission dynamometer based test rig is implemented where the developed pump is built into it and then the variable pump capacity and effect of power reduction are investigated experimentally.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.3
• /
• pp.417-422
• /
• 2022

In this study, the development of a three-screw pump for high-capacity discharge was carried out. Benchmarking and reverse engineering for advanced products were performed to design and manufacture power rotor and idler rotor for high capacity and high pressure. Through flow analysis, performance verification of the entire design was performed and prototypes were manufactured. As a result of performance evaluation on prototypes, it was found that the development specifications were satisfied.

• Transactions of Materials Processing
• /
• v.16 no.2 s.92
• /
• pp.132-137
• /
• 2007

A double roll rotary forming equipment is presented in this paper. The equipment is developed for joining the socket with the ball of a concave piston assembly with its geometrical tolerance requirements satisfied. The equipment is composed of a lathe, a double roll system and a roll pressing unit driven by the hydraulic system. The workpiece rotates by spindle chuck of the lathe while the double roll system approaches perpendicularly to the central line of the workpiece. The equipment is successfully applied to precision joining of the ball and the socket fur the concave piston assembly of a high pressure hydraulic pump.

• International Journal of High-Rise Buildings
• /
• v.12 no.4
• /
• pp.335-341
• /
• 2023

This study proposes a novel rotary direct evaporative cooler and investigates the potential of a moisture-wicking fabric as a cooling pad for the proposed evaporative cooler. The rotary direct evaporative cooler rotates the cooling pad to reduce the water and energy consumption of the pump compared to those of existing direct evaporative coolers. A moisture-wicking fabric is considered as the material of the cooling pad, because of its high moisture-wicking property, enhancing water evaporation. Experiments are performed under various inlet air conditions while measuring the air temperature, relative humidity, air velocity, and differential pressure. The evaporative cooling efficiency and impacts of the inlet air temperature and air velocity on the cooling performance are also evaluated. The results demonstrate the potential of the moisture-wicking fabric as cooling pad of direct evaporative cooler.