• Journal of information and communication convergence engineering
• /
• 제4권4호
• /
• pp.166-169
• /
• 2006

Almost all network systems provide an authentication mechanism based on user ID and password. In such system, it is easy to obtain the user password using a sniffer program with illegal eavesdropping. The one-time password and challenge-response method are useful authentication schemes that protect the user passwords against eavesdropping. In client/server environments, the one-time password scheme using time is especially useful because it solves the synchronization problem. In this paper, we present a new identification scheme: OPI(One Pass Identification). The security of OPI is based on the square root problem, and OPI is secure: against the well known attacks including pre-play attack, off-line dictionary attack and server comprise. A number of pass of OPI is one, and OPI processes the password and does not need the key. We think that OPI is excellent for the consuming time to verify the prover.

• Journal of Welding and Joining
• /
• 제29권3호
• /
• pp.64-69
• /
• 2011

Since welding process for most pipelines with large diameter has been carried out by the manual process, automation of the welding process is necessary for the sake of consistent weld quality and improvement in productivity. Therefore the development of the optimized algorithm to decide the welding condition is an effective technique to prove the feasibility of interface standards and intelligent control technology to increase productivity and reduce the cost of system integration. In this study, the pipe welding experiment has been carried out using plused GMA welding process to select optimal welding condition. And necessary information in root-pass welding has been obtained by applying in the pipeline using the selected welding conditions through the welding experiment.

• Journal of Welding and Joining
• /
• 제28권5호
• /
• pp.86-92
• /
• 2010

In GMAW processes, bead geometry is a criterion to estimate welding quality. Bead geometry is affected by welding current, arc voltage, welding speed, shielding gas and so on. Thus the welding condition has to be selected carefully. In this paper, an experimental method for the selection of optimal welding condition was proposed in the root pass welding which was done along the GMA V-grooved butt weld joint. This method uses the response surface analysis in which the width and height of back bead were chosen as the quality variables of the weld. The overall desirability function, which is the combined desirability function for the two quality variables, was used as the objective function for getting the optimal welding condition. Through the experiments, the target values of the back bead width and the height were chosen as 4mm and 1mm respectively for the V-grooved butt weld joint. From a series of welding test, it was revealed that a uniform weld bead can be obtained by adopting the optimal welding condition which was determined according to the method proposed.

• 한국강구조학회 논문집
• /
• 제10권4호통권37호
• /
• pp.709-720
• /
• 1998

용접잔류응력의 모재두께방향을 포함하는 3차원 분포를 파악하기 위해, 용접상세를 변화시킨 필렛용접이음을 대상으로 해서 실험 및 해석을 수행하였다. 특히, 지금까지 계측이 곤란했던 필렛용접이음의 용접루트부의 잔류응력을 실측하였다. 파라메타로써는 용접입열량과 용접층수를 취급하고, 모재두께방향을 포함하는 3차원 잔류응력의 분포를 조사하였다. 그 결과, 입열량이 증가하면, 용접토우와 루트부를 포함하는 용접부에서는 잔류응력의 크기에 변화가 거의 없지만, 인장잔류응력의 영역이 크게 나타났다. 또 단층과 다층용접의 비교에서는, 다층용접 쪽이 단층용접보다 잔류응력이 상당히 낮음을 알 수 있었다. 용접부 근방의 인장잔류응력의 영역도 다층용접 쪽이 단층용접보다 작게 나타난 것을 알 수 있었다.

• 대한기계학회논문집A
• /
• 제26권2호
• /
• pp.300-307
• /
• 2002

Partial penetration welding joint is defined as groove welds welded from one side, without steel backing or groove welds welded from both sides but without back gouging. So it has an unwelded portion at the root of the weld. Study of partial penetration weldment fracture behavior includes residual stress analysis and fracture analysis. The J-integral loses its path independency in residual stress field. Therefore, it is necessary to introduce a new J-integral, J, which is defined including the effect of plastic deformation and thermal strain. In this study, theoretical formulation and program were developed for the evaluation of J-integral for the crack tip located in the weldment. Evaluations of fracture behavior were performed for partial penetration multi-pass weldment of 25.4mm thick plate by J-integral. From a point of fracture in partial penetration multi-pass welding, it seemed to be better to control root face smaller than 6.35mm.

• 대한기계학회논문집A
• /
• 제25권11호
• /
• pp.1813-1819
• /
• 2001

Partial penetration welding Joint defines that groove welds without steel backing, welded from on side, and groove weeds welded from both sides but without back gouging, that is. it has an unwelded portion at the root of the weld. In this study we analysed fur residual stress and displacement distribution on partial penetration welding condition of thick plate metal. For 25.4mm thick plate, theoretical residual stress and displacement analysis by finite element method using ABAQUS was carried out and compared with the experimental result using hole-drilling method. In results of the condition of partial penetration, it appeared that longitudinal stress at welding area was a little difference and transverse stress did not have any effect by partial penetration multi-pass welding. From a point of welding distortion in partial penetration multi-pass welding, it seemed to be better to control root face smaller than 6.35mm.

• Journal of Welding and Joining
• /
• 제19권6호
• /
• pp.636-642
• /
• 2001

Partial penetration welding joint defines the groove welds that applies the one side welding which does not use steel backing and both side welding without back gouging, that is, the partial penetration welding joint leaves an unwelded portion at the root of the welding area. In this study, we analyzed the residual stress and fracture on the thick metal plates that introduced the partial penetration welding method. As results of using above mentioned welding method, we could draw a conclusion that longitudinal stress and traverse stress occurred around the welding area was so minimal and did not affect any influence. We also performed the fracture behavior evaluation on the partial penetration multi-pass welding with 25.4mm thick plate by using theJ-integral, which finally led us the conclusion that the partial penetration multi -pass welding method is more applicable and effective in handling the root face with less than 6.35mm.

• 한국생산제조학회지
• /
• 제20권1호
• /
• pp.74-80
• /
• 2011

In this study, a variety of welding experiments were carried out to optimize root-pass welding process using GMA process. Based on the experimental results, optimal welding conditions were selected after analyzing correlation between welding parameters and back-bead geometry. Then, effectiveness of empirical models developed was compared and analyzed, and optimized empirical models were finally developed for predicting back-bead by analyzing the main effect of each factor which affects back-bead geometry and their influence on interaction. Also, functions proper for expressing the surface of back-bead were selected using diverse quadratic functions, and back-bead geometry was visualized using empirical models developed and quadratic functions.

• Journal of Welding and Joining
• /
• 제17권5호
• /
• pp.47-54
• /
• 1999

It is well known that solidification cracking often occurs in welds of root pass for one-side welding under the conditions of high welding currents and speeds. In this study, the solidification in 590MPa class steel for pressure vessels SPPV490 was investigated by using flux-cored arc welding(FCAW) with 4 types of welding wires and welding conditions of 200∼280A and 2.8∼ 4.2mm/sec. In order to compared the result of cracking in SPPV490, 0.2%C steel for welded structure of SWS400 and 0.45%C steel for machine structural SM45C were also used as base metals. As the results, all the cracks formed in some welding conditions were observed near the center of weld bead. The solidification cracks were generally initiated near the upper surface of bead and propagated toward the inner part. The solidification cracking generally increased with welding current and welding speed in the same base metal and welding material. In cracking susceptibility, SPPV490 showed higher cracking susceptibility than SWS400 in all welding conditions and welding materials. It was considered that cracking susceptibility could not be evaluated with the hardness of weld metals. The cracking ratio increased with decreasing of a/b(a and b; the width of the upper surface and the back surface of the bead) as shape factor of bead. The cracking tendency with shape factor of bead was extended under the condition of higher welding currents.

• 대한기계학회논문집A
• /
• 제41권4호
• /
• pp.321-327
• /
• 2017

본 연구에서는 수평 자세에서의 TIG 용접 시 반응표면법(RSM)을 이용하여, 최적의 이면비드 형상을 구하는 연구를 진행하였다. 입력변수로는 베이스 전류, 피크 전류, 용접속도를 선정하였고, 이면비드 폭을 용접품질에 관한 출력변수로 하여 목표값을 5.4 mm로 설정하였다. Box-Behnken 실험계획법에 따라 실험을 진행하였고, 비드 폭에 관한 2차 회귀모형을 구한 후, F-테스트를 이용하여 회귀모델을 검정하였다. 그리고 망목특성의 호감도 함수를 사용하여 이면비드 형상을 평가함으로써 최적화를 수행하였다. 이렇게 도출된 최적의 용접조건은 코드화된 값으로 베이스 전류; 0.9204, 피크 전류; 0.8676, 용접속도; 0.3776이었다. 검증실험 결과 목표값에 근접한 5.38 mm의 이면비드 폭을 얻을 수 있었다.