• 열처리공학회지
• /
• 제26권6호
• /
• pp.279-287
• /
• 2013

Oxide Dispersion Strengthened (ODS) Fe with $Al_2O_3$ dispersoid was successfully produced by reactive milling with a mixture of Fe, $Fe_3O_4$ (Magnetite), $Fe_2O_3$ (Hematite) and Al reactants at cryogenic temperature. The milled powders were consolidated by Vacuum Hot Press (HP) at 1323 K, and the consolidated materials were characterized by Transmission Electron Microscopy (TEM), Scanning Transmission Electron Microscopy (STEM), and Energy Dispersive Spectroscopy (EDS); the yield strength and the hardness of the consolidated materials were determined by compressive test and Vickers hardness test at room temperature. The grain size of the materials was estimated by X-ray Diffraction technique using the scherrer's formula. The TEM observations showed that the microstructure was comprised with a mixture of nanocrystalline Fe matrix and $Al_2O_3$ nano-dispersoids with a bimodal size distribution; the 0.2% off-set yield strength of the materials was as high as $758{\pm}29$ MPa and the Vickers hardness was $358{\pm}2$. The effect of the cryogenic milling and addition of extra Fe powder was discussed on the suppression of MSR (Mechanically induced Self-sustaining Reaction) for the desired microstructural evolution of ODS alloys.

• Journal of Welding and Joining
• /
• 제2권1호
• /
• pp.41-48
• /
• 1984

Recrystallization technique was applied to analyze plastic strain at the notch tip of coarse grain HAZ in mild steel (SB 41) and high strength steel (SA 588). The notch tip of specimen was deformed by three point bending. Accumulated displacement (Crack Opening Displacement ${delta}t$) by the monotonic and cyclic loading under room temperature and hot strain embrittlement temperature ($250^{\circ}C$) was 0~1.0mm. Recrystallization heat treatment conditions were $650^{circ}C{ imes}3hr$ for SB 41 and $700^{circ}C{ imes}3hr$ for SA 588. The experimental results obtained were as follows ; 1) Distribution of the effective plastic strain at plastic zone was appeared by the function of crack opening displacement, and plastic zone or the effective plastic strain increased with crack opening displacement. 2) Plastic strain at notch tip of HAZ due to accumulated hot strain calculated as follows. .epsilon. over bar $_{p}$ = .epsilon. over bar $_{cr}$ (x/ $R_{x}$ ) $^{m}$ (m=0.25) 3) Work hardending ratio of notch tip for hot strain was linearly increased with .epsilon. over bar $_{max}$ and dependent upon the material types.s.

• 열처리공학회지
• /
• 제25권3호
• /
• pp.138-145
• /
• 2012

An ${\alpha}$-Ferrite (Fe) powder dispersed with 4 vol.% of $Al_2O_3$ was successfully produced by a simple miling at 210 K with a mixture of $Fe_2O_3$, Fe and Al ingredient powders, followed by 2 step high temperature consolidation: Hot Pressing (HP) at 1323 K and then Hot Isostatic Pressing at 1423 K. The microstructure of the consolidated material was characterized by standard metallographic techniques such as XRD (X-ray Diffraction), TEM and STEM-EDS. The results of STEM-EDS analysis showed that the HIPed materials comprised a mixture of pure Fe matrix with a grain size of ~20 nm and $Al_2O_3$ with a bimodal size distribution of extremely fine (~5 nm) and medium size dispersoids (~20 nm). The mechanical properties of the consolidated materials were characterized by compressive test and micro Vickers hardness test at room temperature. The results showed that the yield strength of the ODS (Oxide Dispersion Strengthened) Fe alloy are as much as $674{\pm}39$ MPa and the improvement of the yield strength is attributed to the presence of the fine $Al_2O_3$ dispersoid.

• 한국재료학회지
• /
• 제28권9호
• /
• pp.495-498
• /
• 2018

Intermetallic compound matrix composites have been expected to be established as high temperature structural components. $Ni_3Al$ is a representative intermetallic alloy, which has excellent ductility even at room temperature by adding certain alloying elements. $Ni_3Al$ matrix composites with aluminum oxide particles, which are formed by the in-situ reaction between the alloy and aluminum borate whiskers, are fabricated by a powder metallurgical method. The addition of aluminum borate whiskers disperses the synthetic aluminum oxide particles during sintering and dramatically increases the strength of the composite. The uniform dispersion of reaction synthesized aluminum oxide particles and the uniform solution of boron in the matrix seem to play an important role in the improvement in strength. There is a dramatic increase in strength with the addition of the whisker, and the maximum value is obtained at a 10 vol% addition of whisker. The $Ni_3Al$ composite with 10 vol% aluminum oxide particles $0.3{\mu}m$ in size and with 0.1 wt% boron powder fabricated by the conventional powder metallurgical process does not have such high strength because of inhomogeneous distribution of aluminum oxide particles and of boron. The tensile strength of the $Ni_3Al$ with a 10 vol% aluminum borate whisker reaches more than twice the value, 930 MPa, of the parent alloy. No third phase is observed between the aluminum oxide and the matrix.

• 한국전자통신학회논문지
• /
• 제8권11호
• /
• pp.1617-1624
• /
• 2013

논문에서는 방화셔터와 피난계단이 존재하는 실내 환경의 화재 시뮬레이션을 실시하여 방화셔터와 화재 확산 사이의 관계를 분석하였다. 화재 시뮬레이션용 상용 소프트웨어인 FDS(Fire Dynamics Simulator)를 사용하여 가상으로 설정한 실내 로비에서 화재 규모와 방화셔터의 개폐 여부를 변화시켜 가면서 모의실험을 실시하였다. 실험을 통해 화재실 벽면과 계단 입구의 온도 변화, 이산화탄소 농도 변화, 연기의 확산 등의 변수들을 구하고 결과를 검토하였다. 피난계단에서 온도와 이산화탄소의 분포는 화재규모와 개구부의 개폐 여부와 별 상관이 없으나, 방화셔터의 부분 하강이 연기의 확산을 막고 있음을 알 수 있었다.

• 소성∙가공
• /
• 제25권6호
• /
• pp.353-358
• /
• 2016

Direct energy deposition (DED) is an additive manufacturing technique that involves the melting of metal powder with a high-powered laser beam and is used to build a variety of components. In recent year, it can be widely used in order to produce hard, wear resistant and/or corrosion resistant surface layers of metallic mechanical parts, such as dies and molds. For the purpose of the hardfacing to achieve high wear resistance and hardness, application of high speed steel (HSS) can be expected to improve the tool life. During the DED process using the high-carbon steel, however, defects (delamination or cracking) can be induced by rapid solidification of the molten powder. Thus, substrate preheating is generally adopted to reduce the deposition defect. While the substrate preheating ensures defect-free deposition, it is important to select the optimal preheating temperature since it also affects the microstructure evolution and mechanical properties. In this study, AISI M4 powder was deposited on the AISI 1045 substrate preheated at different temperatures (room temperature to $500^{\circ}C$). In addition, the micro-hardness distribution, cooling rates, and microstructures of the deposited layers were investigated in order to observe the influence of the substrate preheating on the mechanical and metallurgical properties.

• 수산경영론집
• /
• 제50권3호
• /
• pp.17-29
• /
• 2019

This paper aims to find out the problems and improvement direction of quality control and hygiene management of fishery products in Korea. For this reason, we conducted a comparative analysis of quality control and hygiene management of fishing, landing and selling between Japan and Korea, taking mackerel as an example. Japan has established a systematic freshness management system from fishing to landing (production) areas and consumption areas. On the other hand, Korea is not fully lead-managed in the production area after fishing, and is distributed in a state where the quality of the product is deteriorated due to exposure to room temperature. Accordingly, a certain quality can not be secured at the final consumption stage, and sanitary problems occur. In order to improve the quality control and hygiene management of the fishery products, the following needs to be improved. First, we will improve the fishing level freshness management system. Second, we will improve the quality control and hygiene management of fish in the production area and wholesale stage. Third, we will promote the introduction of innovative sales and consignment sales systems at the production stage. Fourth, we will establish a consistent low temperature distribution system from the production area to the wholesale stage from a long-term perspective. Fifth, we will promote the development and education of manuals on fish quality and hygiene management.

• Nuclear Engineering and Technology
• /
• 제51권6호
• /
• pp.1589-1595
• /
• 2019

In this paper, the CLAM steel strengthened by micro-scale Y-Zr-O was prepared by vacuum induction melting followed by electroslag remelting (VIM-ESR). Yttrium (Y) and zirconium (Zr) were easy to aggregates into massive yttrium-zirconium-rich inclusions in the steel melted by vacuum induction melting (VIM), which would interrupt the continuity of the matrix and reduce the mechanical properties of steel. Micron-sized Y-Zr-O inclusions would be produced with the removal of original blocky Y-Zr-rich inclusions and the submicron-sized inclusions smaller than $0.2{\mu}m$ could be retained in the steel. The small grain size and the better refinement and distribution uniformity of Y-Zr-O inclusions after remelting would be responsible for the better yield strength and toughness. For VIM-ESR alloy, the ultimate tensile strength is 749 MPa and the yield strength is 642 MPa at room temperature, meanwhile they are 391 MPa and 367 MPa at $600^{\circ}C$, respectively. Meanwhile, the ductile-brittle transition temperature (DBTT) reduced from $-43^{\circ}C$ (VIM) to $-76^{\circ}C$ (VIM-ESR).

• 한국정보통신학회논문지
• /
• 제14권10호
• /
• pp.2201-2206
• /
• 2010

최근 한정된 자원으로 인한 에너지 수요가 증가하면서 에너지 절약 문제가 중요한 과제로 대두되었다. 본 논문에서는 효율적인 에너지 절약 문제를 해결하기 위한 방법으로 열 영상과 퍼지 제어 기법을 적용하여 에어콘의 풍향과 풍속을 제어하는 방법을 제시한다. 본 논문에서는 에어콘의 풍향과 풍속을 제어하기 위해 획득한 초기 열 영상을 색상 분포 영상으로 변환하며 각 색상은 $24.0^{\circ}C$에서 $27.0^{\circ}C$의 분포의 온도 값을 가진다. 본 논문에서는 색상 분포 영상을 좌에서 우로 5개의 계층 구간으로 분류하여 온도를 분석한다. 실내 공간의 색상 분포 영상을 분석하여 얻어진 각 계층구간의 온도와 대기 중의 습도를 퍼지 소속 함수에 적용하여 구해진 결과 값을 비퍼지화하고 최종적으로 풍향 세기를 제어한다. 그리고 열 영상을 분석하여 풍향의 우선순위, 풍향의 지속시간을 결정한다. 제안된 방법과 기존 시스템과의 전력량 차이를 시뮬레이션한 결과, 제안된 방법이 효과적임을 확인할 수 있었다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제19권4호
• /
• pp.17-26
• /
• 1995

In general existing air conditioning devices, which are carried out by convection heat transfer, are very popular compared with the radiation type air conditioning devices. But perconal convection tpe air conditioning units are unuseful air conditioning type because it handles amount of surrounded air to meet the temperature and humidity. In this view, this study is intended to develope personal dir conditioning units using a radiation type radiator. Liquid Droplet Radiator(L.P.R.) radiates the energy by means of thermal radiation. Radiative energy from L.P.R. is the infrared rays which heat the objects without lose of energy. It is a desirable heating method for the local area within the large room. In this study, the analysis uses the Monte Carlo methd to predict the temperature distribution in the droplet sheet and the net heat flux from the L.D.R.. And for this study and experiment was carried out to analyse the radiative and convective heat transfer characteristics in the L.D.R.. And the experiment was investigated the effects of inlet temperature, feed rate, optical thickness and droplet diameter on heat transfer characteristics of L.D.R.. The obtained results from the numerical and experimental studies of L.D.R. were as follows ; (1) The heat flux of L.D.R. was effected by extinction coefficient of droplet sheet, optical thickness and droplet temperature, surface area and emissivity of the droplet. And it was increased with the temperature, feed rate and optical thickness, on the other hand decreased with increasing of droplet diameter. (2) The experimental results for heat flux was ecalucted below 20% than that of the numerical solution by Monte Carlo method, but the tendency of the variation shows relatively good agreement.