• International Journal of Highway Engineering
• /
• v.10 no.1
• /
• pp.41-48
• /
• 2008

This paper deals with the characteristics of earth pressure to the debris-fall prevention walls which usually are installed in front of steep slope. Such walls have narrow backfill width where the active soil wedge can not be developed fully. The earth pressure to such walls ue affected by the movement of wall and arching effects due to the friction developing on the surface of adjacent ground slope and wall and therefore cannot be analyzed and calculated reliably. The study is carried out through laboratory model tests using centrifuge test. Test results reveal that the earth pressure to the debris-fall prevention wall depends largely on the inclination angle of the ground slope and the wall movement. The earth pressure reduction due to wall movement was observed at the upper half of wall, while the arching effect was significant at the lower half especially in the case of steep ground slope. It can be said that from the result of this study in the design of a debris-fall prevention wall the earth pressure should be determined considering the inclination of ground slope and the condition of wall movement during and after construction.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.4 no.3
• /
• pp.51-60
• /
• 2001

The travel behavior can be analysed microscopically using GPS because the travel characteristics can be found out by travelling two test cars loaded with GPS equipments. The speed difference and spacing variation between the lead vehicle and the following's in uninterrupted flow are the important variables related to capacity and safety. This study analysed these with data obtained by travelling the 4th Line and 28th Line of the national road. The variation width in speed difference in the run time is below 3.0%. But, related to the speed difference in the situation of acceleration and deceleration the difference after 4second is bigger than that just after the start. The spacing variation is similar to this. The spacing just before deceleration concerning safety was analysed. When the theoretical values by the modeling method and observed values were compared, the observed values were analysed 12.52% shorter than the other in average.

• Journal of the Korean Society of Environmental Restoration Technology
• /
• v.20 no.3
• /
• pp.45-54
• /
• 2017

With rapid urbanization and reckless urban development in the 21st century, the urban environment has gradually gotten worse, and urban heat island effect has been dramatically intensified. Thus, the importance of street greenery that can mitigate the urban heat island effect has further been highlighted. In this regard, this study was aimed at selecting suitable plant species for street greenery to reduce the urban heat island effect. Towards this end, five roads located in Seocho-gu, Seoul were selected as study sites, and plant species composition and difference of surface temperature were compared and analyzed in relation to the light transmittance. The street with the greatest temperature difference is Bangbae-ro(Platanus occidentalis). On the other hand, the road with the lowest temperature difference is Nambusunhwan-doro(Metasequoia Glyptostroboides). The effect of temperature reduction was found to be associated with light transmittance.Bangbae-ro(Platanus occidentalis) with the lowest light transmittance showed the highest temperature difference and Nambusunhwan-doro(Metasequoia Glyptostroboides) with the highest light transmittance showed the lowest temperature difference. It is analyzed that there are most differences in temperature when the amount of lights coming in between the crown is small. The temperature reduction effect can be obtained by planting deciduous broad-leaved trees. Also species with dense crown and broad width of crown will be able to maximize the effect of temperature reduction. In future studies, it will be necessary to expand the other species of trees in the street, and analyze the germicidal trees and shrubs as well as the differences in the packaging materials.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.6 s.97
• /
• pp.615-621
• /
• 2005

In this paper, a model for simulating synthetic aperture radar(SAR) images of earth surfaces. The earth surfaces include forest area, rice crop field, other agricultural fields, grass field, road, and water surface. At first, the backscattering models are developed for bare soil surfaces, water surfaces, short vegetation fields such as rice fields and grass field, other agriculture areas, and forest areas. Then, the SAR images are generated from the digital elevation model(DEM) and digital terrain map. The DTM includes ten parameters, such as soil moisture, surface roughness, canopy height, leaf width, leaf length, leaf density, branch length, branch density, trunk length, and trunk density, if applicable. The scattering models are verified with measurements, and applied to generate an SAR image for an area.

• International Journal of Highway Engineering
• /
• v.13 no.2
• /
• pp.115-123
• /
• 2011

This study was conducted to investigate the early-age behavior and performance of precast pavements constructed by replacing existing asphalt pavements for an intersection in urban bus only lanes. The monitoring items included level differences between asphalt pavement and precast panels at the beginning and ending locations of the precast pavement, level differences and joint widths between precast panels, precast panel settlement, and skid resistance of the panel surface. At a certain time after the construction, the diamond grinding method was applied and its effect was also investigated. The monitoring results showed that as time went by, the panel level, joint width, settlement, and skid resistance were not much varied. That implied the stable sustaining of external loads by the precast pavements. In addition, it was verified that employing diamond grinding could reduce the level differences between precast panels.

• Water for future
• /
• v.8 no.2
• /
• pp.30-40
• /
• 1975

Hydrogeological survey and geophysical prospecting have been carried out in Saudi Arabia for the purpose of finding groundwater in the soil and rock at the request of General trading company in Jeddah, Saudi Arabia. The surveyed area is located on $38^{\circ}-39^{\circ}$ 30' in longitude and $26^{\circ}-26^{\circ}$ 30' in latitude. The topography of this area is dominated by northwest southeast mountain range composed mostly of precambrian rocks and basalt of tertiary period. Geology is mainly composed of greenstone, granite, andesite, diorite rhyolite of pre-cambrian era and sandstone of cambrian period which are underlained by basalt and andesite of tertiary period and alluvium of quaternary unconformably. The instruments used in this investigation are TR-18B2 radioactivity unit which isjapanese patented and A.C. Terrameter, a resistivity meter manufactured by ABEM of Stockholm, Sweden. Radioactivity method has been conducted along the Alula-Khaybar road, totally 164Km by the car-borne. As a result of the above survey 16 places have been selected and these anomalies show 1.2N-1.6N compared to background of each area in intensity with width of 10-50m. Resistivity vertical profiling which made use of Schlumberger configuration method has been made over selected areas by radioactivity method to provide hydrogeological information for a water resources survey. The result of resistivity shows that good aquifers are located in the western part of surveyed area where sedimentary rock is distributed. The strata showing 10-50, ${\Omega}-m$ in resistivity are thought to be waterbearing layer. The variations in aquifer resistivity found, are thought to be due to verying clay content, which could be related to aquifer yield. It has proved impossible to detect small salinity variation in the buried aquifer by geophysics. As a result of resistivity prospecting 10 places are recommended to be drilled at the anomalies as shown attached map. yields from the proposed holes have been estimated approximately from $20m^3$ to $200m^3$ per day. Prior to drilling for groundwater, test boring using ${\c}4"$ should be drilled in order to obtain more reliable hydrogeological information for the construction of perfect wells.ells.

• Journal of Environmental Impact Assessment
• /
• v.19 no.3
• /
• pp.347-356
• /
• 2010

Forests are being seriously fragmented as a result of land development. Land development with disregard to its subsequent environmental impacts is a primary threat to biodiversity by incurring massive habitat losses and changes in structure and composition of forests. The purpose of this study was to develop the impact assessment model for quantitative distance or degree of disturbance by land developments. This study conducted a survey about structure and composition of forest species to determine degree of impact from land development. The edge effect of forest fragmentation on the number of bird species, population size, and bird diversity was obvious. In particular, the bird diversity sharply declines around the forest edge where intensive land development projects take place. To assess the disturbance of forest species, the factors selected were the bird diversity and the rate of edge species. The impact assessment model about bird diversity was explained by type of forest fragmentation and type of vegetation ($R^2$=0.23, p<0.005). The other model about edge species explained by a distance, type of forest fragmentation, type of vegetation, and width of road ($R^2$=0.34, p<0.001). In order to test the applicability of the model developed in this study, the models was applied to the Samsong housing development in Goyang-si, Gyunggi-do. The impacts of land development on the bird species were reasonably quantified to suggest effective mitigation measure. The impact assessment model developed in this study is useful to assess the magnitude of disturbance of bird species. Particularly, the model could be applied to the current Environmental Impact Assessment practices to predict and quantify the impacts of land developments projects on forest bird species.

• International Journal of Highway Engineering
• /
• v.20 no.3
• /
• pp.65-73
• /
• 2018

PURPOSES : In this study, the propriety of expansion joint spacing of airport concrete pavement was examined by using weather and material characteristics. METHODS : A finite element model for simulating airport concrete pavement was developed and blowup occurrence due to temperature increase was analyzed. The critical temperature causing the expansion of concrete slab and blow up at the expansion joint was calculated according to the initial vertical displacement at the joint. The amount of expansion that can occur in the concrete slab for 20 years of design life was calculated by summing the expansion and contraction by temperature, alkali-silica reaction, and drying shrinkage. The effective expansion of pavement section between adjacent expansion joints was calculated by subtracting the effective width of expansion joint from the summation of the expansion of the pavement section. The temperature change causing the effective expansion of pavement section was also calculated. The effective expansion equivalent temperature change was compared to the critical temperature, which causes the blowup, according to expansion joint spacing to verify the propriety of expansion joint applied to the airport concrete pavement. RESULTS : When an initial vertical displacement of the expansion joint was 3mm or less, the blowup never occurred for 300m of joint spacing which is used in Korean airports currently. But, there was a risk of blow-up when an initial vertical displacement of the expansion joint was 5mm or more due to the weather or material characteristics. CONCLUSIONS : It was confirmed that the intial vertical displacement at the expansion joint could be managed below 3mm from the previous research results. Accordingly it was concluded that the 300m of current expansion joint spacing of Korean airports could be used without blowup by controling the alkali-silica reaction below its allowable limit.

• Journal of Korean Society of Transportation
• /
• v.34 no.3
• /
• pp.248-262
• /
• 2016

The study documents the analysis on characters and symbols shown in the pavement markings in the perspective of mathematics educators. The purpose of this study is to propose a pavement marking method that can enhance readability from the driver's eye position. To this end, this study analyzed the figure of the pavement markings that can be actually recognized by the projective geometry perspective. As a result, it proposed alternatives to the current pavement markings by introducing the concept of the compression ratio. Results of the study are as follows. First, the rule was established to obtain the compression ratio. If the observation of two viewing angles are x and y, then the compression ratio S is ${\sin}y/{\cos}\(\frac{x-y}{2}\)$. Second, we presented two alternatives to the pavement marking method for the displayed information. One is a method for improving the pavement markings in terms of the compression ratio, the other is a method by varying vertical length of the pavement markings while holding its width constant. Based on the outcomes from this study, a mathematical analysis can be further studied for the perception of speed according to the types of pavement marking line.

• Journal of the Korean Society of Safety
• /
• v.32 no.4
• /
• pp.100-106
• /
• 2017

Outline map is used for the description and reconstruction of the traffic accident. One way to produce the outline map is by adopting detailed measurements from the accident site such as final position of the vehicle and pedestrian, width of the road, and locations of the oil and tire marks. This method consumes large amount of time not to mention that of the production of detailed version as fine as the picture of the site. Aerial recording equipment so called HeliCam can produce an outline map that can substitute that of manual method with even faster production time and higher resolution. However, the produced picture have errors which are resulted by distortion due to the characteristics of camera and direction of the photographing. This paper provides correction of the distortion of oultline map produced by HeliCam using Adobe Photoshop and PC-Rect. The result showed resonable error range less than 6 cm(0.1%) for $60m{\times}30m$ area taken by HeliCam. The presented method develops outline map with small error, which is useful to traffic accident analysis, and traffic accident cases analyzed in this study were also.