• 한국입자에어로졸학회지
• /
• 제8권2호
• /
• pp.47-54
• /
• 2012

Paved road dust emissions were investigated 14 times on 12 main roads in Seo-Cho Gu, Seoul, Korea by vehicle-based mobile sampling system(Road Dust Monitoring System) during September to December 2011. Also, fourteen heavy metals present in the dust samples were analyzed by ICP. ICP analysis showed that one of major source of the road dust would be urban construction. A large amount of silt was found, which might be originated mainly from building construction and open beds of trees. Trace element and pollution indices of heavy metals(Cd, Cu, Ni, Pb, Zn) on the roads adjacent to the commercial area had higher concentrations than those on the roads adjacent to the construction and residential areas because of traffic density and heavy traffic.

• 환경영향평가
• /
• 제9권4호
• /
• pp.257-269
• /
• 2000

This study is to investigate the methodology and applicability on emission control by both MECHANICAL Model and Fugitive Dust Model (FDM) through the comparison of field measurement data and calculated data. Comparing to the method of AP-42 emission fector on the production of flying dust the MECHANICAL Model was proved to be more applicable to the calculation emission rate on the various dust emission conditions on a unpaved road. The seperate calculation on annual mean emission amount and a 24working hours amount was undertaken for the easy management of fugitive dust. Dust concentration predicted by FDM is similar with a measurement value.

• 한국환경과학회지
• /
• 제13권12호
• /
• pp.1145-1150
• /
• 2004

Dust phenomenon is a critical thing in the East Asian countries. However, it is quite recent that Asian dust has drawn much attention and the scientific investigation of dust particles began. In this study, the recognition for Asian-dust in Northeast Asia region was analyzed. The survey results show that the people generally recognize the origins and seriousness of Asian dust and understand the difficulty in solving the dust related problems. However, approaches to figure out Asian dust have many difficulties and limits in scientific, economic and political points of view and more detailed road map is needed based on government policy.

• 한국응용과학기술학회지
• /
• 제35권1호
• /
• pp.284-291
• /
• 2018

본 연구에서는 식품 및 화장품 원료로 널리 사용되는 천연 다당류의 분자 구조, 분자량, 점도, 친수성, 팽창, 습윤 및 보습 특성을 이용하여 도로 분진 방지제를 제조하였다. 다양한 분진 제어 효과가 확인되었으며 단순한 물 분사 및 시험 대조군인 합성PVA보다 우수한 결과를 얻었다. 또한 수분증발 비교, 비산 저감율, 공사현장 테스트 및 물벼룩 급성 독성 시험 등의 영향을 연구하고 토양 및 수질의 안전성을 연구하여 도로 분진 방지제의 유용성을 확인하였다.

• Elastomers and Composites
• /
• 제57권3호
• /
• pp.92-99
• /
• 2022

A large amount of particles on the roads is produced by friction between the vehicles and the road surface and by inflow from outside. The type of these particles affects the abrasion behavior of tire tread. In this study, road dust collected at a bus stop was separated by size, and the particles with sizes of 106-212 mm were analyzed. The particles were separated by density using NaI and NaBr aqueous solutions with densities in the range of 1.10-1.80 g/cm³ with the 0.10 g/cm³ interval. In the road dust sample, the following particle types were found: tire-road wear particles (TRWPs), asphalt pavement wear particles (APWPs), plant-related particles (PRPs), road paint wear particles (RPWPs), and plastic particles (PPs). The densities of TRWPs, APWPs, PRPs, and RPWPs were 1.20-1.80, >1.60, >1.10, and >1.40 g/cm³, respectively, while PPs were found in all density ranges. Additionally, many small mineral particles were observed on the particles. Order of the relative content of the particles was PRP > TRWP > APWP ~ RPWP > PP. APWPs that were stuck to TRWP could be removed by chloroform treatment. The shapes of the particles were characterized using their magnified images.

• 한국컴퓨터정보학회논문지
• /
• 제26권8호
• /
• pp.181-185
• /
• 2021

도로 미세먼지는 단순히 대기오염의 문제가 아닌 보도를 이용하는 보행자 등 국민의 건강과 생명을 위협하고 있다. 이에 도로 미세먼지 저감과 관련하여 다양한 정책안이 있으나 실질적인 효과에 대해서는 장담할 수 없는 상황이다. 따라서 국민의 안전하고 쾌적한 통행을 보장하기 위해 도로 미세먼지 관리형 보도포장(인도포장)을 장소, 용도, 기능 등을 고려하여 적합한 포장 재료 및 공법을 선정하여 설계하거나 보도 시설 등을 마련하여야 할 것이다. 이에 본 연구에서는 보도포장의 개념 및 법적근거를 살펴보고 대기오염을 정화하는 보도포장 관련 기술 현황 등을 검토하여 미세먼지 저감용 보도포장 지침 개정안, 「녹색제품구매촉진에 관한 법률」상 보도포장재 활용방안, 지방자치단체 보도포장 관리 규칙 개정안 등을 제시하여 인도포장 기술을 조기에 적용할 수 있는 법적 기반을 구축하고자 한다.

• Elastomers and Composites
• /
• 제56권2호
• /
• pp.85-91
• /
• 2021

In this study, different types and shapes of various particles produced on the asphalt pavement road were analyzed. Road dust at a bus stop was collected and was separated as per their sizes by using a sieve shaker. Tire-road wear particles (TRWPs), asphalt pavement wear particles (APWPs), mineral particles, plant-related particles, glass beads, glass particles, road paint wear particles, plastic particles, and fibers were observed herein. The types and shapes of the particles varied depending on their sizes. TRWPs larger than 500 ㎛ were not observed. TRWPs with a size of 212-500 ㎛ were rarely present, but many TRWPs with a size smaller than 212 ㎛ were observed. APWPs were observed for whole-particle sizes of below 1,000 ㎛. A variety of particles on the road would lead to lower friction between the tires and the road, thereby increasing the braking distance of vehicles. Most of the particles include mineral particles, glass particles, and APWPs with rough surfaces. Therefore, the abrasion of the tire tread would accelerate owing to friction with the tough particles.

• 한국대기환경학회지
• /
• 제31권2호
• /
• pp.105-117
• /
• 2015

Sources related to road dust is one of the biggest sources, which is responsible for a large portion of emission. In particular, PM2.5 is a potential cause for respiratory diseases, thus it should be managed and a mitigation plan using results of statistical apportionment modeling such as chemical mass balance needs to be established. Recently, identifying sources of PM2.5 and analyzing the contribution of the road dust through a contribution assessment is required. Therefore, this study provides the chemical source profiles of PM2.5 using IC, GC/MS, OCEC, and XRF for both paved sidewalk and paved roadway collected at seven different sampling sites. As a result, for paved sidewalk, $NH{_4}^+$ (70%), $NO{_3}^-$ (12%), $PO{_4}^-$ (9%), and $SO{_4}^{2-}$ (9%) have been analyzed in PM2.5 mass. Major molecular marker such as Si has been indicated as $12.0{\pm}3.4%$ and $13.6{\pm}6.9%$ for paved sidewalk and roadway, respectively. PAHs such as Fluoranthene, Pyrene, Chrysene, and 1,3,5-Triphenylbenzene are suggested as molecular markers for road dust.

• 한국조경학회지
• /
• 제13권1호
• /
• pp.1-24
• /
• 1985

The pinus trees planted by the road in the Seoul -Suwen high-way was surveyed on the damages due to air pollution during April and May in 1984. The results were as follows ; The concentration of SO$_2$was ranged from 0.003 to 0.05ppm, NOx from 0.03 to 0.1ppm and the amount of dust fall, from 10 to 110ton/km$^2$/month. While the concentrations of gaseous pollutants such as SO$_2$and NOx were notsignificantly different in the type of road and with in the distence of 20 meters from the road the dust falls were decreased as remoted from the road. The tissue damages of leaves were determined by the microscopic observation. The higher concentration of dust fall on the leaf, the more severe damage observed in the stomata. The attached dust of the leaves were ranged from 1l to 75mg/g of leaf, and those were significantly incereased as near from road. The sulfur contents of leaves were measured at 0.15g/100g of leaf in the 5 meters located and at 0.064g/100g of leaf in the 20 meters, and the lead contents, 45ug/g of leaf in the 5 meters and 24ug/g in the 15 meters. The appearent damages of plant were very much corelated to the attached dusts of leaves the sulfur contents and the amount of dust fall, and the multiple regression analysis between the damages and factors of air pollution were under taken. As increment of vehicle in future, the air Pollution was predicted and the plant damages were estimated.

• Elastomers and Composites
• /
• 제34권3호
• /
• pp.212-221
• /
• 1999

Mechanical properties of polypropylene filled with recycled rubber dusts obtained from the buffing process in sport shoe sole manufacture were investigated. The use of these dusts eliminates the need for the size reduction process which is usually employed in rubber recycling. Two different waxes, polypropylene wax and ethylene vinyl acetate wax, were used in the PP/rubber dust compound. Two different processes, extrusion and injection moulding, were used to study the influence of the blends on the properties. The waxes gave significant improvement in the shaping of the extrudate. It was found that the impact strength of the injection moulded samples were higher than the extruded samples and the virgin PP. The tensile properties (yield stress and modulus) were dependent on the amount of rubber dust addition. An increase in the rubber dust loading gave lower yield stress and modulus.