• Journal of Power Electronics
• /
• v.17 no.3
• /
• pp.590-600
• /
• 2017

This paper presents a ripple-free input current modified interleaved boost converter for high step-up applications. By integrating dual coupled inductors and voltage multiplier techniques, the proposed converter can reach a high step-up gain without an extremely high turn-ON period. In addition, a very small auxiliary inductor employed in series to the input dc source makes the input current ripple theoretically decreased to zero, which simplifies the design of the electromagnetic interference (EMI) filter. In addition, the voltage stresses on the semiconductor devices of the proposed converter are efficiently reduced, which makes high performance MOSFETs with low voltage rated and low resistance $r_{DS}$(ON) available to reduce the cost and conduction loss. The operating principles and steady-state analyses of the proposed converter are introduced in detail. Finally, a prototype circuit rated at 400W with a 42-50V input voltage and a 400V output voltage is built and tested to verify the effectiveness of theoretical analysis. Experimental results show that an efficiency of 95.3% can be achieved.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.9 no.6
• /
• pp.553-558
• /
• 2016

A DC-DC converter for CMOS image sensors in bio-sensor chips is proposed. The DC-DC converter generates a PCP voltage, that is an on voltage of a pixel, and an NCP voltage, that is an off voltage of a pixel. The PCP voltage with a ripple voltage of within 1.33V is obtained from a positive charge pump of VPP (=5V) with a ripple voltage of 45.35 by using a regulator. Also, the NCP voltage with a ripple voltage of 0.05mV is obtained from a negative charge pump of VNN (=-2V) with a ripple voltage of 62.8 by using a regulator.

• Proceedings of the KIPE Conference
• /
• 2003.07b
• /
• pp.575-578
• /
• 2003

This paper presents a new current control method to reduce torque ripple of Brushless DC Motor during commutation. In the proposed control strategy, the current slopes of rising and decaying phase during commutation is equalized by the compensation voltage. By adding the compensation voltage for it to the current controller output, the reduced torque ripple can be obtained. The simulation and experimental results show that the proposed method reduces the torque and the current ripples significantly.

• Journal of Power Electronics
• /
• v.16 no.3
• /
• pp.1036-1045
• /
• 2016

This paper presents a novel control strategy for passive output filter reduction using an active output filter. The proposed method achieves the dual-function of regulating the output voltage ripple and output voltage variation during load transients. The novel control strategy allows traditional simple voltage controllers to be used, without requiring the expensive current sensors and complex controllers used in conventional approaches. The proposed method is verified with results from a 125-W forward converter.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.21 no.5
• /
• pp.453-456
• /
• 2016

The major causes of electrical fire in low-voltage distribution lines are classified into short-circuit fault, overload fault, electric leakage, and electric contact failure. The special principal factor of the fire is electric arc or spark accompanied with such electric faults. This paper studies the development of an electric fire prevention system with detection and alarm of that in case of parallel arc fault occurrence in low-voltage distribution lines. The proposed system is designed on algorithm sensing the instantaneous voltage drop of line voltage at arc fault occurrence. The proposed detector has characteristics of high-speed operation responsibility and superior system reliability from composition using a large number of semiconductor devices. A new sensing control method that shows the detection of parallel arc fault is sensed to ripple voltage drop through a diode bridge full-wave rectifier at electrical accident occurrence. Some experimental tests of the proposed system also confirm the practicality and validity of the analytical results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.1
• /
• pp.91-102
• /
• 2013

This paper proposes the improved LCCT(Inductor-Capacitor-Capacitor-Trans) Z-source DC-DC converter (Improved LCCT ZSDC) which can generate the bipolar output voltages according to duty ratio D. The proposed converter has the characteristic and structure of Quasi Z-source DC-DC converter(Quasi ZSDC) and conventional LCCT Z-source DC-DC converter(LCCT ZSDC). To confirm the validity of the proposed method, PSIM simulation and a DSP based experiment were performed for each converter. In case which the input DC voltage is 70V, the bipolar output DC voltage of positive 90V and negative 50V could generate. Also, as comparison result of the capacitor voltage ripple in Z-network and the input current under the same condition for each converter, the voltage stress and the capacitor voltage in Z-network of the proposed method were lower compared with the conventional methods. Finally, the efficiency for each method was investigated according to load variation and duty ratio D.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.6
• /
• pp.1003-1011
• /
• 2008

In this paper, optimal design of interleaved boost converters is studied in order to design low ripple, size, loss and high performance converters for fuel cell applications. Also, the process of optimal design of interleaved boost converter has been performed. Input current ripple, output voltage ripple, losses and capacity of electrical components are theoretically analyzed and informative simulation and experimental results are provided.

• Proceedings of the KIPE Conference
• /
• 2003.07a
• /
• pp.102-105
• /
• 2003

The leakage inductance of the High frequency Transformer(HFT) in the flyback topology can be used an inductor of the Low Pass Filter(LPF) to reduce ripple and ripple noise in the output voltage. But, the values of leakage inductance and magnetizing inductance in the HFT are within $\pm20[{\%}]$). And the operating temperature of the HFT increased by the leakage inductance. Therefore, the leakage inductance of the HFT in the flyback topology has minimum and the LPF has non-polarity ceramic capacitor in the output stage. In this paper, the LPF in the flyback topoBogy takes PCB capacitor using double layer of PCB without non-polarity ceramic capacitor. Its experimental results show the reduced ripple noise and the reduced ripple in the output stage.

• Proceedings of the KIPE Conference
• /
• 1998.10a
• /
• pp.79-84
• /
• 1998

A novel zero voltage and zero current switching (ZVZCS) full bridge (FB) PWM converter with low output current ripple is presented. A simple auxiliary circuit added in the secondary provides ZVZCS conditions to primary switches, ZVS for leading-leg switches and ZCS for lagging-leg switches, as well as reduces the output current ripple (ideally zero ripple). The auxiliary circuit includes neither lossy components nor additional active switches which are demerits of the previously presented ZVZCS converters. Many advantages including simple circuit topology, high efficiency, low cost and low current ripple make the new converter attractive for high performance high power (＞1kW) applications. The principle of operation, features and design considerations are illustrated and verified on a 2.5kW, 100KHz IGBT based experimental circuit.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.66 no.7
• /
• pp.1047-1052
• /
• 2017

In this paper, the calculation torque using the d-q axis has advantage like faster execution time. However, the torque ripple can't be considered in the torque calculation using d-q axis equivalent circuit because the time-dependent component is removed. When d-q transformation was performed, it was founded that some parameters has some characteristics. These characteristics were considered for representing torque ripple. The calculation with d-q axis transformation and Finite Element Analysis(FEA) were performed, and the results were compared. As a result, it was validated that the calculated torque can be expressed with ripple.