• Transactions of The Korea Fluid Power Systems Society
• /
• v.7 no.1
• /
• pp.1-5
• /
• 2010

This paper presents the experimental results of the radial piston type oil pump with new mechanism for a metal diaphragm hydrogen compressor. Generally, metal diaphragm type hydrogen compressor systems are operated by oil hydraulic power. In this system an oil compensating pump has been demanded to compensate for a leakage oil head chamber. The metal diaphragm type hydrogen compressor consists of an oil compensating pump, commonly used hydraulic piston pump and driven by main crank shaft. The radial piston type oil compensating pump with new rolling contacted piston mechanism is developed and experimented. The developed piston element of the radial piston pump consists of piston, steel ball, return spring, two check valves, eccentric cam and ball racer. In this study, designed 4 type pistons as and orifice hole. Operating characteristics and pressure ripple characteristics are tested under no load to 60bar loaded with every 20bar increasing step and pressure ripple and flow rate are experimentally investigated.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.1
• /
• pp.36-41
• /
• 2011

Medical X-ray has been brought many changes according to the rapid development of high technology. Especially, for high-voltage generator which is the most important in X-ray generation the traditional way is to use high-voltage electric transformers primarily. However, since it is large and heavy and the ripple rate of DC high-voltage applied to X-ray tube is too big, it has a disadvantage of low X-ray production efficiency. To solve these problems, the studies about high-voltage power supply are now proceeding. At present, the high-voltage generator that generates high-voltage by making high frequency using inverter control circuit consisting of semiconductor device is mainly used. High-voltage generator using inverter has advantages in the diagnosis using X-ray including high performance with short-term use, miniaturization of power supply and ripple reduction. In this study, the X-ray high-voltage device with inverter type using pulse width modulation scheme to the control of tube voltage and tube current was designed and produced. For performance evaluation of produced device, the control signal analysis, irradiation dose change and beam quality depending on the load variation of tube voltage and tube current were evaluated.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.4
• /
• pp.381-389
• /
• 2004

In this paper, it is suggested that instantaneous compensation PWM control for inverter without the smoothing capacitor Therefore, this inverter system has several advantages. It has small volume and low price to manufacture, decrease trouble rate of inverter, and has power factor correction effect because huge smoothing capacitor-less. And it has compact size control circuit to use analog integrator device. It could make the smoothing capacitor-less inverter for air-blower motor by using the instantaneous compensation PWM controller. This inverter system has small volume and value compare with the conventional VVVF control inverter.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.1015-1016
• /
• 2006

The important parameters deciding the fluctuation of Accumulation style surgical operation of ventriculus laser beam are smoothing capacitor, frequency and he characteristics of laser resonator. In this thesis, we control the fluctuation of medical $CO_2C$ laser in realtime by changing Duty-Ratio of IGBT and switching frequency with fixed the smoothing capacitor to improve the fluctuation of laser beam. We detect the light on laser resonator using a CdS photo sensor to improve ripple factor of laser beam and feedback fluctuated signals refined by a band pass filter into the control circuit to stabilize fluctuation actively. There is much to be desired in the realtime controlling technique of the light on Accumulation style surgical operation of ventriculus laser discharge tube in electrical signal. We propose switching control technique with microprocessor and photo sensing technique by controlling switch devices optimum operation and feedback signals detected by a photo sensor into the laser power supply in order to improve ripple factor of the $CO_2$ laser beam.

• Journal of Power Electronics
• /
• v.13 no.3
• /
• pp.349-361
• /
• 2013

As a result of the advantages such as high efficiency, continuous current and high stability margin, push-pull converter with continuous current (PPCWCC) is competitive for battery discharge regulator (BDR) which plays an important role in power conditioning unit (PCU). Leakage inductance yields current spike in low-ripple current of PPCWCCs. The operating modes are added due to leakage inductance. Therefore the steady state performance is affected, which is embodied in the spike of low-ripple current. PPCWCCs which are suitable for BDR can be separated into three types by current spike characteristics. Three representative topologies IIs1, IIcb2 and Is3 are analyzed in order to investigate the factors on the magnitude and duration of spike. Equivalent current sampling method (ECSM) which eliminates the sampling time delay and achieves excellent dynamic performance is adopted to prevent the spike disturbance on current sampling. However, ECSM reduces the sampling accuracy and telemetry accuracy due to neglecting the spike. In this paper, ECSM used in PPCWCCs is summarized. The current sampling error is analyzed in quality and quantity, which provides the foundation for offsetting and enhancing the telemetry accuracy. Finally, current sampling error rate of three topologies is compared by experiment results, which verify the theoretical analysis.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.457-458
• /
• 2006

A method for obtaining smooth, jerk bounded feed rate profile in high speed machining has been developed. This study proposes a NURBS interpolator based on adaptive feed rate control with a well developed look ahead algorithm which takes into account the machining dynamics as well. Limitation of jerk and proportional torque rate result in smoothened loads on the machine which effectively reduces excitation of the resonant frequencies of the machine. It is found that the values of the feed rate of the down stream sharp corner have profound effect on the feed rate of the upstream sharp corners. By using a windowing scheme the feed rate profile obtained after look ahead method is re-interpolated to reduce the jerk related problems. This is compared with the adaptive NURBS interpolator to show the effectiveness of the proposed method. Simulation results indicate that the consideration of 'ripple effect' is important in avoiding jerk and thereby increasing the machining accuracy.

• Proceedings of the KIEE Conference
• /
• 2001.07e
• /
• pp.116-119
• /
• 2001

In this research, we detect the charge state within $0.1{\sim}0.3[A]$ and develop the intelligent digital charge device by applying a fine pulse signal using PWM inverter and Proportional-Integral(PI) controller which uses micro -processor and intelligent technique. The ripple rate is within ${\pm}1%$, and the indicator error rate of full charge state is within ${\pm}1%$, and the voltage stability is within ${\pm}0.1[V]$, and the accuracy of voltage detect is 48[V] and ${\pm}0.5[V]$ in the reference of 100[A].

• Proceedings of the KIEE Conference
• /
• 2005.10c
• /
• pp.135-137
• /
• 2005

In servo system demanding precision dynamic characteristics, application of the Permanent Magnet Linear Synchronous Machines (PMLSM) has advantage of analysis convenience by simple geometry and thrust ripple reduction from the sinusoidal back electromotive force and excited stator. Therefore, this paper presents design of surface-mounted PMLSM with slotless iron cored stator according to coil turns to satisfy the rate thrust. Also, from dynamic analysis for servo application of manufactured motor with heavy mass, we offer accurate range of the DC link voltage and acceleration in rate speed. This is applied to speed reference profile considering system characteristics in total length of moving position.

• Analyses & Alternatives
• /
• v.4 no.2
• /
• pp.71-102
• /
• 2020

This study analyzes the effect of demographic changes on economic growth. We use the supply-side output identity to forecast the growth potential of the Korean economy. According to the results, even based on optimistic assumptions and prospects, the economic growth rate is likely to fall drastically starting in 2020. Of course, to maintain growth potential, efforts to increase productivity are necessary. However, given the historical experience of developed countries, it is not clear whether the huge trend of demographic change can be offset by efforts to increase productivity. In the so-called '30-50 club' countries, both labor productivity and growth rate tend to fall after reaching the per capita income of $30,000. The degree of decline in the growth rate is closely related to changes in the working age population and the prime-age workforce. The results are similar when tracking the path of changes in total factor productivities of the economy. When a certain level of income is reached, the increase in total factor productivity also tends to slow down. The ripple effects of rapid changes in demographics will indeed be extensive. The negative impact is likely to be concentrated at a time when the working age population, the prime-age workforce, and the total population shrink simultaneously. Above all, it is necessary to use the government's fiscal space to block the possibility of a rapid fall in the growth rate. In addition, it is important to continuously implement various reform tasks that should be promoted, such as improving the education system and strengthening the social safety net.

• Journal of Information Technology Applications and Management
• /
• v.30 no.1
• /
• pp.33-52
• /
• 2023

This study observes the difference in the actual regional ripple effect of the decrease in admission resources due to the decrease in school age population, which has been weak in empirical studies, and how much the decrease in competition rate by department nationwide provides a significant shock to the decrease in enrollment rate in the population unit. An empirical quantitative analysis was attempted. As a result of applying the panel-tobit regression model, a clear gap was confirmed in the decrease in the registration rate due to the decrease in the competition rate both nationally and in the provinces, and in particular, a highly significant relationship was derived with the decrease in the recruitment rate. In particular, the sensitivity of the risk of unrecruitment due to a decrease in competition rate was the highest in the Jeolla region (0.499), followed by the Gangwon region (0.475) and the Gyeongsang region (0.471), and the metropolitan region (0.158) was confirmed to be the most stable. This suggests that the gap in insufficient funding has gradually widened by region over the past 10 years, and that the shock wave becomes more pronounced in the provinces farther away from the metropolitan area. Based on this study, if we deviate from the standardized application of university development policies for the metropolitan area and regional universities, and present a customized higher education strategy for each region, it will be an opportunity to prevent local extinction due to a decrease in the school-age population and achieve coexistence with higher education institutions and regions at the same time.