• Journal of Sensor Science and Technology
• /
• v.20 no.3
• /
• pp.172-177
• /
• 2011

Finger patients can't use their hands because of the paralysis their fingers. Their fingers are recovered by rehabilitating training, and the rehabilitating extent can be judged by measuring the pressing force to be contacted with two fingers(thumb and first finger, thumb and middle finger, thumb and ring finger, thumb and little finger). At present, most hospitals have used a thin plastic-plate for measuring the two-finger grasping force, and we can only judge that they can grasp the plate with their two-finger through it, because the plate can't measure the two-finger grasping force. But, recently, the force measuring system for measuring two-finger grasping force was developed using three-axis force sensor, but it is very expensive, because it has a three-axis force sensor. In this paper, two-finger force measuring system with a one-axis force sensor which can measure two-finger grasping force was developed. The one-axis force sensor was designed and fabricated, and the force measuring device was designed and manufactured using DSP(Digital Signal Processing). Also, the grasping force test of men was performed using the developed two-finger force measuring system, it was confirmed that the grasping forces of men were different according to grasping methods, and the system can be used for measuring two-finger grasping force.

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.3
• /
• pp.324-333
• /
• 2012

The conventional medium and large caliber gun, in general, utilize the hydro-pneumatic recoil mechanism to control the firing impulse and to return to the battery position. However, this kind of mechanism may cause the problems like the leakages and the property changes in oil and gas due to the temperature variations between low and high temperatures. Accordingly, the friction spring mechanism has recently been researched as an alternative system. The friction spring mechanism consists of a set of closed inner and outer rings with the concentric tapered contact surfaces assembled in the columnar form, and can only be used under the compression load. When the spring column is axially loaded, the tapered surfaces become overlapped, causing the outer rings to expand while the inner rings are being contracted in diameter allowing an axial displacement. Because of friction between tapered contact surfaces, much higher spring stiffness is obtained on the stroke at the increase in load than the stroke at the decrease. In this paper, the dynamic equations regarding the friction spring system and the design approach have been investigated. It is also tried for a dynamic model representing the recoil motion and the friction spring forces. And the model has been proved from firing test using a gun system with friction springs. All the results show that the recoil mechanism using friction springs can substitute for the classic hydro-pneumatic recoil system.

• Geotechnical Engineering
• /
• v.14 no.5
• /
• pp.29-38
• /
• 1998

The purpose of this research is to develop an amended clay liner by utilizing waste lime produced as a by-product in chemical industries. Waste lime contains various kinds of organics which affect the permeability, compactability, and unconfined compressive strengths of soil. The geotechnical engineering properties of waste were improved by adding other materials so that they might meet the EPA requirement of clay liner. Granite weathered soil, which is abundant in Korea and can be obtained easily in the field. was used as a primary additive to improve geotechnical engineering properties of waste lime. Various kinds of laboratory tests related to geotecnnical engineering properties, required to evaluate the design criteria for the clay liner in the solid waste landfill. were carried out by changing miRing ratio of waste lime with additive. According to the laboratory test results, in order to obtain the appropriate amended clay liner. the effective miffing ratio of waste lime in granite weathered soil was proved to be about 20~30%.

• Asian Pacific Journal of Cancer Prevention
• /
• v.17 no.4
• /
• pp.2055-2060
• /
• 2016

Background: Colorectal cancer (CRC) is one of the most common causes of death worldwide and in Thailand. The X-ray repair cross-complementary protein 1 (XRCC1) is required for efficient DNA repair. The effects of this gene on survival in colorectal cancer remain controversial and have not been reported in Thailand. The aim of this study was to investigate the association of the XRCC1 gene with survival of colorectal cancer patients in a Thai population. Materials and Methods: Data and blood samples were collected from 255 newly diagnosed and pathologically confirmed CRC patients who were recruited during the period 2002 to 2006 and whose vital status was followed up until 31 October, 2014. Real-time PCR-HRM was used for genotype identification. The Kaplan-Meier method, the log-rank test, and Cox proportional hazard regression were used to estimate cumulative survival curves and compare various survival distributions and adjusted hazard ratios. Results: Most of the cases were males, and the median age was 55 years. The median survival time was 2.43 years. The cumulative 1-, 3-, 5-, 7-, and 10 year survival rates were 76.70%, 39.25%, 26.50%, 16.60% and 3.56%, respectively. After adjustment, female gender, ages 50-59 and ${\geq}60years$, tumour stage III+IV, a signet-ring cell carcinoma, and poor differentiation had significant associations with increased risk of CRC death. While the XRCC1 Arg/Arg homozygote appeared to be a risk factor for CRC death, the association was not significant. Conclusions: The genetic variant in the XRCC1 may not be associated with the survival of CRC patients in Thailand. Further studies are needed to verify our findings.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.7 no.3
• /
• pp.75-81
• /
• 2005

The experiment aimed at knowing the effect of physiology and psychology according to season on color preference. Two tests, one of the spring and the other of the autumn was conducted. Seventy subjects with normal color vision served as subjects. The subjects entered a bioclimatic chamber controlled at a temperature of $25\pm1^{\circ}C$, a relative humidity of $50\pm5\%$ and a light of 1000 1x. The subjects wearing white shirts and trousers sat quietly on a sofa for one our. Sensation from warm to cool colors might be possibly different individually Therefore, a subject asked to array 41 randomly placed cloth colors from very warm to very cool colors during rest quietly for one our. All subjects arrayed these cloth colors in the order from red through yellow and green to blue, which had the reproducibility. After rest, they were instructed to choose a single one out of 41 cloth colors, preferred by themselves, every 10min during one our 0-ring test were measured to red, yellow, white, blue, black, favorite color, and dislike color. Most subjects preferred warmer color in April than in December. Tympanic temperature was significantly lower in December than in April. Finger presser was significantly higher in like color than in dislike color but it was no significant differences between spring and autumn. The preferring the warm color in April toward summer when basal metabolic rate is decreased than in December toward winter when it is increased can explain that physiology reaction by load error between actual core temperature and set-point induces psychological reaction to pursue visual alliesthesia. Our present experiment revealed that the preferred color could be determined by the relationship between the internal temperature and its set point according to season. It should be emphasized that the alliesthesia was observed also in the realm of visual system.

• Proceedings of the KOSOMBE Conference
• /
• v.1997 no.11
• /
• pp.249-254
• /
• 1997

ABA-type block copolymers composed of poly(L-leucine)(PLL) as the A component and poly(ethylene glycol)(PEG) as the B component were synthesized by ring-opening polymerization of L-leucine N-carboxyanhydride initiated by primary amino group located at both ends of PEG chain. A silver sulfadiazine(AgSD)-impregnated wound dressing of sponge-type was prepared by the lyophilization method. Morphological structure of this wound dressing obtained by scanning electron microscopy(SEM) was composed of a dense skin layer and a macroporous inner sponge layer. Equilibrium water content(EWC) of wound dressing was above 10%. It increased with an increased of PEO content in the block copolymer due to the hydrophilicity of PEO. AgSD release from AgSD- impregnated wound dressing in PBS buffer(pH=7.4) was dependent on PEG composition in the block copolymer. Therefore, EWC and release of AgSD can be control by PEG composition. Antibacterial capacity of AgSD-impregnated wound dressing was examined in agar plate against Pseudmonas aeruginosa and Stapplococus aruous. Cytotoxicity of the wound dressing was evaluated by studing mouse skin fibroblast(L929). From the behavior of antimicrobial releasing and the investigation of the suppression of bacterial proliferation, it was supposed that the wound dressing containing antibiotics could protect the wound surfaces from bacterial invasion to suppress the bacterial proliferation effectively. In cytotoxicity observation, cellular damage was reduced by the control led released of AgSD from the LEL sponge matrix of AgSD-medicated wound dressing. In vivo test, granulous tissue formation and wound contraction or the AgSD and DHEA impregnated wound dressing were aster than any other groups.

• Journal of Preventive Medicine and Public Health
• /
• v.6 no.1
• /
• pp.81-85
• /
• 1973

One hundred and thirty one health articles (as 'original articles') reported in medical journals published in Korea during the period from Jan. to Dec. 1971. were selected as the study materials for tile purpose of resumption and criticism. Of a total of 131 articles, thirty-nine were not required the statistical application for the data processing and drawing their conclusions and ninty-two, 70.2%, were needed to apply. The 92 articles were divided into three groups by the types of study: 54 for experimental study, 30 for clinical case analytic study and 8 for field study. Each report was resumed and criticised under the statistical aspects in terms of data processing and the validity of the conclusions. The results of resumption of the 92 articles needed statistical application are summarized as follow; 1. Of the 54 articles of experimental studies resumed, thirty-one articles, 57.4%, were considered acceptable. Among the 38 articles classified as clnical case analytic and field studies, only 28.9 per cent were considered acceptable. In total 45.7 per cent or less than half were considered acceptable. 2. Types of errors encountered are as shown in Table 3. 3. The most frequently encountered error was that the conclusions were drawn without having made any statistical test. This type of error was found in 14 out of 35 errors presented in experimental studies, 11 of 35 in clinical case analytic studies and 5 of 9 in field studies and 30 out of 97, 38.2%, in total.

• Economic and Environmental Geology
• /
• v.29 no.3
• /
• pp.325-333
• /
• 1996

numerical model is developed to estimate gas flow in the landfill site. Darcy's law, the mass conservation law, and the ideal gas state equation are combined to compose the governing equation for the steady-state and transient-state gas flows. The finite element method (FEM) is used as the numerical solution scheme. Two-dimensional radial symmetric triangular ring element is used to discretize the simulation domain. The steady state model developed in this study is compared with AIRFLOW that is a commercial model developed by Hydrologic Inc. Mass balance test is performed on the transient gas flow simulation. The developed model is applied to analyze the gas extraction experiment performed by Daewoo Institute of Construction Technology at the Nanjido landfill in 1993. The developed model was registered at Korea Computer Program Protection Foundation.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.4
• /
• pp.10-16
• /
• 2007

A rubber seal for wheel bearing which has been mainly applied to car wheel supporting device is required to have both high sealing performance and drag torque. Because of severe operational conditions like infiltration of mud or splashed water, the importance of rubber seal which is aimed for leakage prevention of grease and effective blocking of foreign substances has been increasing continuously. The sealing performance of this seal depends on several factors such as materials of seal, friction conditions of contact regions and geometry of seals and so on. We have focused on the effects of geometric characteristics such as the angle of main lip, interference between lip edge and inner metallic ring. In this study, the optimization of geometric variables was performed using the finite element analysis. For the sake of finite element analysis, uniaxial tensile tests were conducted and several constants for Mooney-Rivlin's equation were obtained. According to the results of this study, mock-up bearing was made. To verify this study, drag torque and mud spray test were preformed.

• Korean Journal of Materials Research
• /
• v.27 no.7
• /
• pp.386-391
• /
• 2017

Using a customized diffusion bonder, we executed diffusion bonding for ring shaped white gold and red gold samples (inner, outer diameter, and thickness were 15.7, 18.7, and 3.0 mm, respectively) at a temperature of $780^{\circ}C$ and applied pressure of 2300 N in a vacuum of $5{\times}10^{-2}$ torr for 180 seconds. Optical microscopy, field emission scanning electron microscopy (FE-SEM), and energy-dispersive X-ray spectroscopy (EDS) were used to investigate the microstructure and compositional changes. The mechanical properties were confirmed by Vickers hardness and shear strength tests. Optical microscopy and FE-SEM confirmed the uniform bonding interface, which was without defects such as micro pores. EDS mapping analysis confirmed that each gold alloy was 14K with the intended composition; Ni and Cu was included as coloring metals in the white and red gold alloys, respectively. The effective diffusion coefficient was estimated based on EDS line scanning. Individual values of Ni and Cu were $5.0{\times}10^{-8}cm^2/s$ and $8.9{\times}10^{-8}cm^2/s$, respectively. These values were as large as those of the melting points due to the accelerated diffusion in this customized diffusion bonder. Vickers hardness results showed that the hardness values of white gold and red gold were 127.83 and 103.04, respectively, due to solid solution strengthening. In addition, the value at the interface indicated no formation of intermetallic compound around the bonding interface. From the shear strength test, the sample was found not to be destroyed at up to 100,000 gf due to the high bonding strength. Therefore, these results confirm the successful diffusion bonding of 14K white-red golds with a diffusion bonder at a low temperature of $780^{\circ}C$ and a short processing time of 180 seconds.