• Journal of Power Electronics
• /
• v.15 no.4
• /
• pp.886-898
• /
• 2015

The design feasibility of a micro unidirectional DC transmission system based on an input-parallel output-parallel (IPOP) converter is analyzed in this paper. The system consists of two subsystems: an input-parallel output-series (IPOS) subsystem to step up the DC link voltage, and an input-series output-parallel (ISOP) subsystem to step down the output voltage. The two systems are connected through a transmission line. The challenge of the delay caused by the communication in the control system is addressed by introducing a ring communication structure, and its influence on the control system is analyzed to ensure the feasibility and required performance of the converter system under practical circumstances. Simulation and experiment results are presented to verify the effectiveness of the proposed design.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.148-153
• /
• 2004

This paper represents that parts of a large generator operating in 1000 MW are affected by centrifugal forces due to high-speed rotation in 3600 rpm and 3D FEM Analyses are required to obtained the structural reliability of the generator. From these results, one would know the weakest locations and the stress distributions. The fatigue life is calculated in order to grasp the remaining life of generator. 2D and 3D analyses are performed to calculate stresses of the generator rotor and the retaining ring. From 2D results, we find the SCF at the slot and sub-slot of the rotor. 3D analysis is applied at the end part of generator rotor, which represents complex geometry, and rotor and retaining ring shrink thermally. With these results, designers of rotor and retaining ring can compare with the results of design code and verify the stress distributions of generator rotor and retaining ring, and then calculate the remaining life from the low-cycle fatigue data.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.11b
• /
• pp.37-43
• /
• 2002

In this paper, we analyse and present mechanical dynamic characteristics of a micro-machined vibrating silicon ring gyroscope which can measure angular velocities about three orthogonal axes. The ring gyroscope has a ring connected to the gyroscope main body by support-ligaments which are arranged with cyclic symmetry. The natural modes of its vibration can be distinguished into the in-plane motion and the out-of-plane motion which are coupled by the gyro-effect due to the rotation of the gyroscope main body. The equations of motion, the response to angular velocities, and the relationships between the natural modes of vibration are derived and compared with the previous studies for the design of a micro three-axis ring gyroscope.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.17-20
• /
• 1999

In these days, wavelength division multiplexing(WDM) all-optical network are being deployed to support various multimedia communication services. In this paper, various WDM all-optical network are discussed, and a design of an all-optical backbone network has been proposed by using multiple self-healing ring technology. The proposed multiple self-healing ring network improves network expandability and efficiency of bandwidth, while it retains simplicity and ease of network control, which are from the nature self-healing ring. Using PDI traffic modeling technique, a well-balanced all-optical backbone network using multiple self-healing ring is designed for the 2010s in Korea.

• Tribology and Lubricants
• /
• v.13 no.2
• /
• pp.89-95
• /
• 1997

This paper considers two dimensional analysis for lubrication between the single piston ring and the cylinder liner. The piston ring is treated as a reciprocating, hydrodynamic bearing with combined sliding and squeeze motion. Reynolds' equation is used, to model lubrication with Reynolds' cavitation boundary condition. This analysis is developed to get the cyclic variation of minimum film thickness and viscous frictional force. Two types of piston ring face shape are considered. This result can be used to study the influence of ring shape design parameter to improve the characteristics of sealing and lubrication.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.12
• /
• pp.1001-1009
• /
• 2002

In this paper, we analyse and present mechanical dynamic characteristics of a micro-machined vibrating silicon ring gyroscope which can measure angular velocities about three orthogonal axes. The ring gyroscope has a ring connected to the gyroscope main body by support-ligaments which are arranged with cyclic symmetry. The natural modes of its vibration can be distinguished into the in-plane motion and the out-of-plane motion which are coupled by the gyro-effect due to the rotation of the gyroscope main body. The equations of motion, the response to angular velocities, and the relationships between the natural modes of vibration are derived and compared with the previous studies for the design of a micro three-axis ring gyroscope.

• Journal of the Optical Society of Korea
• /
• v.14 no.1
• /
• pp.38-41
• /
• 2010

We design and fabricate a widely tunable laser diode made of InGaAsP-InP. The diode is monolithically integrated with a wavelength-selective coupled-ring reflector and semiconductor amplifiers. For realization of a compact size device, deeply etched multi-mode interference couplers and square ring resonators composed of total-internal-reflection mirrors are adopted and fabricated using a self-aligned process. It is demonstrated that the laser diode exhibits single mode operation and 16 nm tuning range with side-mode-suppression-ratio exceeding 20 dB.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.4
• /
• pp.537-545
• /
• 2013

The elastic recovery of a metal seal is a factor that can be used to assess its sealing performance. In this study, a compliant mechanism topology optimization has been performed to find a structure of a metal O-ring seal that can maintain excellent sealing performance with a maximized elastic recovery over extended operation. An evolutionary structural optimization (ESO) was used as a topology optimization algorithm with two different types of objective functions considering both flexibility and stiffness. In particular, a circular design domain was adopted to consider the outer shape of the metal O-ring seal. The elastic recovery of the optimal topology was calculated and compared to that of a commercial product.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.10
• /
• pp.2551-2556
• /
• 2009

The principal operation of a ring laser gyroscope depends on the phase difference for the counter-propagating waves within a closed path. The reflection mirrors mounted on the resonator block form the traveling waves. Thus, the dimension accuracy of resonator block influences the traveling path of beam. In order to maintain the stable optical beam path in the ring resonator, the piezo-driven moveable mirror is adopted for the path length control under the thermal expansion or mechanical strain of resonator block. This paper presents the mathematical description of the elastic behavior of piezo-driven mirror. This description can be applied for the concept design of piezo-driven mirror.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.5
• /
• pp.436-442
• /
• 2009

This paper describes a study on the design of compact polymer bushing with inner control shield. In the bushing, a high electric stress occurred between field shaper and central conductor by the closely space. Also coaxial cylindrical shield has a great height along the axis to control an electric field. Consequently, all the potentials are raised axially along the field shaper and electric stress is concentrated on a part of the surface of the FRP tube near the upper end of the field shaper. In accordance, the field control can be achieved by means of the designs of such inner control shields. The floating and ring shield designs was decreased electric field concentration at critical parts of the bushing. The shield gaps is formed between field shaper and ring shield. Accordance equipotential lines extend through gaps. As a result, the resulting electrical stress are thus reduced in the range $17{\sim}23%$ in the bushing with floating and ring shield designs. Maxwell 2D simulator based on the boundary element method was also introduced in order to verify the reliability of the polymer bushing. The optimized design uses internal elements for electric stress grading at critical parts of the bushing.