• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.108-109
• /
• 2014

본 논문에서는 gate와 drain bias stress하에서의 a-IGZO thin-film transistors (TFTs)의 비대칭 열화 메커니즘 분석을 진행하였다. Gate와 drain bias stress하에서의 a-IGZO TFT의 열화 현상은 conduction band edge 근처에 존재하는 oxygen vacancy-related donor-like trap의 발생으로 예상되며, TFT의 channel layer 내에서의 비대칭 열화현상은 source의 metal과 a-IGZO layer간의 contact에 전압이 인가되었을 경우, reverse-biased Schottky diode에 의한 source 쪽에서의 높은 electric field가 trap generation을 가속화시킴으로써 일어나는 것임을 확인할 수 있었다.

• Journal of Digital Contents Society
• /
• v.5 no.3
• /
• pp.187-191
• /
• 2004

Rapid time variations of the mobile communication channel have a dramatic effect on the performance of multi-carrier modulation. This paper analyzed the bit error rate (BER) performance for multi-carrier code division multiple access (MC-CDMA) network, and derived the equivalent signal-to-total noise plus interference(SNIR) of MC-CDMA system in the reverse link, the performance of MC-CDMA/BPSK signal is evaluated taking into account the fraction of partial-band interference and interference power. and the effect of partial-band interference is comprehensively studied in order to further improve the Qos of multi-carrier multimedia system.

• ETRI Journal
• /
• v.19 no.3
• /
• pp.116-140
• /
• 1997

The base station transceiver subsystem (BTS) of the CDMA Mobile System is interfaced to mobile stations over the air and to the wired network through a packet switched interconnection network. The potential benefits of CDMA technology are achieved when the transmitter and the receiver are properly designed and implemented. The physical layer of the interface at the base station is implemented with the CDMA ASICs and control circuits in channel card of the BTS. We present the design perspectives and structural illustration of the BTS. Base station modem ASICs and their control to implement the CDMA receiver, Baseband and RF signal processing blocks, and BTS controller are described. Elaborate power control is essential to ensure the high capacity which is one of advantages of the CDMA technology. The closed loop reverse link power control and the forward link power control operated in the BTS are described.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 1998.05a
• /
• pp.150-154
• /
• 1998

CDMAPCS 시스템은 Rake 수신기를 이용만 경로 다이버시티를 채택하여 우수한 시스템 향상을 얻을 수 있어 주로 TDMA 시스템에서 적용하고 있는 등화기를 사용할 필요가 없다. 그러나 CDMA PCS 시스템의 역방향 링크에서는 순방향과는 달리 채널의 크기 및 위상 추정에 필요한 파이롯 채널이 없어 성능의 저하를 가져오게 된다. 따라서 역방향 링크에서 채널환경에 따라 Rake 수신기의 성능에 미치는 영향을 분석하는 것은 중요하다. 본 논문에서는 시스템 성능 및 광대역 채널 파라미터 분석을 위해 광범위한 라이브러리와 시스템 구성의 유연성을 가지고 있는 Ptolemy [1] 플랫폼에서 CDMA PCS 시스템의 역방향 링크 규격에 따라 각 블록을 사용자 정의로 구현하였다. Ptolemy 시뮬레이터를 이용하여 CDMA PCS 시스템의 역방향 링크 비트오율 성능을 채널의 특성과 연관지어 분석하였다. 그리고 가상할 수 있는 각 채널 모델을 이용하여 CDMA PCS 시스템의 성능과 광대역 채널 파라미터 (예: 지연확산)와의 상관 관계를 파악하였다. 본 연구에서 CDMA PCS 시스템에서는 일반적으로 알려져 있는 지연확산보다 평균지연 파라미터가 더 높은 상관 관계가 있음을 발견하였다.

• Biomolecules & Therapeutics
• /
• v.24 no.3
• /
• pp.252-259
• /
• 2016

Neuropathic pain is a complex state showing increased pain response with dysfunctional inhibitory neurotransmission. The TREK family, one of the two pore domain $K^+$ (K2P) channel subgroups were focused among various mechanisms of neuropathic pain. These channels influence neuronal excitability and are thought to be related in mechano/thermosensation. However, only a little is known about the expression and role of TREK-1 and TREK-2, in neuropathic pain. It is performed to know whether TREK-1 and/or 2 are positively related in dorsal root ganglion (DRG) of a mouse neuropathic pain model, the chronic constriction injury (CCI) model. Following this purpose, Reverse Transcription Polymerase Chain Reaction (RT-PCR) and western blot analyses were performed using mouse DRG of CCI model and compared to the sham surgery group. Immunofluorescence staining of isolectin-B4 (IB4) and TREK were performed. Electrophysiological recordings of single channel currents were analyzed to obtain the information about the channel. Interactions with known TREK activators were tested to confirm the expression. While both TREK-1 and TREK-2 mRNA were significantly overexpressed in DRG of CCI mice, only TREK-1 showed significant increase (~9 fold) in western blot analysis. The TREK-1-like channel recorded in DRG neurons of the CCI mouse showed similar current-voltage relationship and conductance to TREK-1. It was easily activated by low pH solution (pH 6.3), negative pressure, and riluzole. Immunofluorescence images showed the expression of TREK-1 was stronger compared to TREK-2 on IB4 positive neurons. These results suggest that modulation of the TREK-1 channel may have beneficial analgesic effects in neuropathic pain patients.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.3A
• /
• pp.342-350
• /
• 2000

In this paper, the bit error performance for the reverse link of a synchronous direct sequence code division multiple access (DS-CDMA) system employing an imperfect power control scheme over a frequency selective Rayleigh fading channel is analyzed. The system capacity degradation due to power control error (PCE), which is approximated by a log-normally distributed random variable, is estimate as a function of a standard deviation of the PCE. In addition, the impact of the multipath intensity profile (MIP) shape and the number of resolvable paths on the performance of the synchronous transmission is investigated. To estimate the system capacity, the coded bit error performance is evaluated and compared with the conventional CDMA. It is found tat synchronous transmission has less sensitivity to imperfect power control and eases the power control requirements. In particular, as the decay constant $\delta$ of MIP increases, the synchronous transmission in the DS-CDMA reverse link results in a significant BER improvement over the asynchronous transmission even in the presence of imperfect power control. We further conclude that the capacity can be improved by employing the synchronous transmission.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.1
• /
• pp.143-150
• /
• 1997

The electrical properties of polysilicon thin films implanted with $B_2H_6$ diluted in $H_2$ as dopant source using ion mass doping technique and the effect of radiation damage on the dopant activation behavior were investigated. Comparing the SIMS profiles of boron in polysilicon films with that obtained from computer simulation using TRIM92 the most probable ion species were $B_2H_x\;^+$(x＝1, 2, 3‥‥) type molecular ions. As a result of the Implantation of energetic massive ions, a continuous amorphized layer was created in polysilicon films where the fraction of amorphized layer varied with doping time. This amorphization comes from the fact that mass separation of implanting species is not employed in this ion mass doping technique. In the dopant activation behavior, reverse annealing phenomenon appeared in the intermediate annealing temperature range for a severely damaged specimen. The experimental result showed that the off-state current of the p-channel polysilicon thin film transistor is dependent on the degree of radiation damage.

• The Korean Journal of Physiology and Pharmacology
• /
• v.20 no.2
• /
• pp.177-183
• /
• 2016

We fortuitously observed a human neutrophil intracellular free-calcium concentration ($[Ca^{2+}]_i$) increasing activity in the commercially available phosphodiesterase I (PDE I), which is actually dried crude venom of Crotalus atrox. As this activity was not observed with another commercially available pure PDE I, we tried to find out the causative molecule(s) present in 'crude' PDE, and identified Lys49-phospholipase A2 (Lys49-PLA2 or K49-PLA2), a catalytically inactive protein which belongs to the phospholipase A2 family, by activity-driven three HPLC (reverse phase, size exclusion, reverse phase) steps followed by SDS-PAGE and LC-MS/MS. K49-PLA2 induced $Ca^{2+}$ influx in human neutrophils without any cytotoxic effect. Two calcium channel inhibitors, 2-aminoetoxydiphenyl borate (2-APB) ($30{\mu}M$) and SKF-96365 ($20{\mu}M$) significantly inhibited K49-PLA2-induced $[Ca^{2+}]_i$ increase. These results suggest that K49-PLA2 modulates $[Ca^{2+}]_i$ in human neutrophils via 2-APB- and SKF-96365-sensitive calcium channels without causing membrane disruption.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.26 no.12B
• /
• pp.1677-1685
• /
• 2001

In this paper, we propose a call admission control scheme that can be performed within guaranteeing of required QoS(Quality of Services) in DS-CDMA(Direct Sequence-Code Division Multiple Access) reverse link. It has been performed rely on a physical channel numberonly and based on quality of received signal from MODEM(modulator/demodulator) part in established study. In other methods, the standard for services would have been set from statistical analysis of users\` location and using received power level in BTS(Base Transceiver Station). These ways bring about not only system loads but time delay or great differences from real environment. To solve these problems, we propose a call drop rate estimation algorithm for the purpose of call admission control based on measured value at LNA(Low Noise Amplifier) ports of BTS(Base Transceiver Station) in real time. This method proposed in this paper estimates a quality of offered service in real time, reduce system loads and shorten time delay which is needed to determine the standard for call admission control. But it requires a additional 17W complexity which can measure received signal power in BTS and estimate call drop rate.

• Design & Manufacturing
• /
• v.12 no.2
• /
• pp.27-33
• /
• 2018

Korea's automobile industry, which has grown rapidly to become the world's fifth-largest automobile producer, To cope with environmental pollution and energy problems in order to prevail competitive edge in global market We are investing a lot of research personnel and costs. Among them, for realizing alternative light weight It is a part of the automobile module system that has achieved the technological development before the breakthrough in the injection molding process in the press process. Door module PNL was the subject of research. The door module PNL is expected to cause warpage before the mold production due to the thin and flat product characteristics and fiber orientation characteristic of the material. In this paper, CAE analysis and reverse correction tool Design. CAE analysis to obtain the results of weld line position, bending position and deformation value Through the correction tool, think3, the original product was modified before the mold production to improve the completeness of the parts. In fiber orientation, the position and size of the cooling channel in the mold, the position and size of the gate, Temperature, pressure, time, and work environment. Compared with the result of CAE analysis, the product that was reverse-corrected by Think3 was manufactured, and injection molding was performed. Injection molding products were tested 24 hours later. 3.5 mm to 7.0 mm, and under the fixed condition, the deviation was from 1.1 mm to 1.5 mm. Unlike the CAE analysis, the deviation of the actual injection pressure and the cooling temperature, the fiber orientation of the material, In order to solve this problem, it is necessary to compare the injection conditions with the database, I knew I had to catch the standard.