• International Journal of Naval Architecture and Ocean Engineering
• /
• v.11 no.1
• /
• pp.380-395
• /
• 2019

Seakeeping, especially for the roll motions, is of critical importance to the safe operation of fishing boats in Indonesia. In this study, a traditional East Java Fishing Boat (EJFB) has been analysed in terms of its seakeeping performance. Furthermore, a bilge keel was designed to reduce the roll motions of the EJFB using multiple stages approach. After installing the designed bilge keels, it was shown that up to 11.78% and 4.87% reduction in the roll response of irregular seaways and the total resistance under the design speed, respectively. It was concluded that the roll-stabilized-EJFB will enhance the well-being of the fisherman and contribute to the boats' safe operation, especially in extreme weather conditions. Moreover, the total resistance reduction of the EJFB due to the installation of the designed bilge keels also resulted in increased operational efficiency and reduced fuel costs and fuel emissions for local stakeholders.

• KEPCO Journal on Electric Power and Energy
• /
• v.5 no.1
• /
• pp.39-43
• /
• 2019

Hydrogen energy has positive effects as an alternative energy source to overcome the energy shortage issues. On the other hand, since stability is very important in use, sensor technology that enables accurate and rapid detection of hydrogen gas is highly required. In this study, hydrogen sensor was developed on AlGaN/GaN heterostructure platform using Pd catalyst where a recess structure was employed to improve the sensitivity. Temperature and bias voltage dependencies on sensitivity were carefully investigated using a hydrogen concentration of 4% that is the safety threshold concentration. Due to the excellent properties of AlGaN/GaN heterostructure in conjunction with the recess structure, a very high sensitivity of 56% was achieved with a fast response speed of 0.75 sec.

• Journal of IKEEE
• /
• v.24 no.4
• /
• pp.1074-1080
• /
• 2020

This paper proposes a digitally controlled buck converter insensitive to process, voltage and temperature and capable of three modes of operation depending on the state of the output voltage. Conventional digital-controlled buck converters utilized A/D converters, counters and delay line circuits for accurate output voltage control, resulting in increasing the number of counter and delay line bits. This problem can be resolved by employing the 8-bit and 16-bit bidirectional shift registers, and this design technique leads a buck converter to be able to control duty ratio up to 128-bit resolution. The proposed buck converter was designed and fabricated with a CMOS 180 nano-meter 1-poly 6-metal process, generating an output voltage of 0.9 to 1.8V with the input voltage range of 2.7V to 3.6V, a ripple voltage of 30mV, and a power efficiency of up to 92.3%. The transient response speed of the proposed circuit was measured to be 4us.

• International Journal of Advanced Culture Technology
• /
• v.9 no.1
• /
• pp.224-241
• /
• 2021

According to data from the National Police Agency, 75.5 percent of dead traffic accidents in Korea are truck accidents. About 1,000 people die in cargo truck accidents in Korea every year, and two to three people die in cargo truck accidents every day. In the survey, Korean cargo workers answer poor working conditions as an important cause of constant truck accidents. COVID 19 is increasing demand for non-face-to-face logistics. The inefficiency of the Korean transportation system is leading to excessive work burden for small logistics The inefficiency of the Korean transportation system is causing excessive work burden for small individual carriers. The inefficiency of the Korean transportation system is also evidenced by the number of deaths from logistics industry disasters that have risen sharply since 2020. Small and medium-sized Korean Enterprises located in CIPs (Connected Industrial Parks) often do not have smart access certification systems. And as a result, a lot of transportation time is wasted at the final destination stage. In the logistics industry, time is the cost and time is the revenue. The logistics industry is the representative industry in which time becomes money. The smart access authentication system architecture proposed in this paper allows small logistics private carriers to improve legal stability, and SMEs (Small and Medium-sized Enterprises) in CIPs to reduce logistics transit time. The CIPs smart access system proposed in this paper utilizes the currently active Mobile OTP (One Time Password), which can significantly reduce system design costs, significantly reduce the data capacity burden on individual cell phone terminals, and improve the response speed of individual cell phone terminals. It is also compatible with the OTP system, which was previously used in various ways, and the system reliability through the long period of use of the OTP system is also high. User customers can understand OTP access systems more easily than other smart access systems.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.44 no.6
• /
• pp.1154-1162
• /
• 2020

In this study, the soft textile actuator is produced for a smart wearable with the shape memory effects from linear shape memory alloys of Nickel and Titanium using the driving force through the fabrication process. The measurement model was designed to measure dynamic characteristics. The heating method, and memory shape of the linear shape memory alloy were set to measure the operating temperature. A shape memory alloy at 40.13℃, was used to heat the alloy with a power supply for the selective operation and rapid reaction speed. The required amount of current was obtained by calculating the amount of heat and (considering the prevention of overheating) set to 1.3 A. The fabrication process produced a soft textile actuator using a stitching technique for linear shape memory alloys at 0.5 mm intervals in the general fabric. The dynamic characteristics of linear shape memory alloys and actuators were measured and compared. For manufactured soft textile actuators, up to 0.8 N, twice the force of the single linear shape memory alloy, 0.38 N, and the response time was measured at 50 s.

• Journal of the wind engineering institute of Korea
• /
• v.22 no.4
• /
• pp.171-177
• /
• 2018

In order to investigate the cause of damage of the offshore meteorological tower, the measured wind speed data were analyzed, the dynamic displacement due to fluctuating wind load and wave load was calculated, and the fatigue was examined for vortex-induced vibration. It was confirmed from the results that the vibration lasting for four hours occurred in the meteorological tower when the maximum wind speeds for 10 minutes were compared for both the vane anemometer and ultrasonic anemometer. The effect of the gust wind on the dynamic response of the meteorological tower was greater than the wave. However, the combined forces acting on the meteorological tower was much lower than the design force even though the wind and wave loads were simultaneously applied. The vortex-induced vibration seemed to be cause of the fatigue failure in the connecting bolts. The destruction of the offshore meteorological tower was considered to be a vortex-induced vibration, not a fluctuating fluid flows.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.20 no.4
• /
• pp.117-134
• /
• 2010

A passive RFID tag which received attention as a future technology for automatic and quick identification faces some difficulties about security problems such as tag authentication, reader authentication, data protection, and untraceability in addition to cost and reliable identification. A representative passive RFID technology is the ISO/IEC 18000-6 Type C which is an international standard for 900 MHz UHF-band. This standard has some difficulties in applying to the security services such as originality verification, tag's internal information protection, and untraceability, because it does not provide high-level security solution. In this paper, we summarize security requirements of ISO/IEC ITC 1/SC 31 international standardization group, propose security protocols suitable for the UHF-band passive RFID system using a crypto engine, and analyze its security strength. In addition, we verify that it is possible to implement a tag conforming with the proposed security protocols by presenting concrete command/response pairs and cryptographic method.

• Advances in nano research
• /
• v.10 no.2
• /
• pp.151-163
• /
• 2021

The main target of this study is to investigate nonlinear transient responses of moving polymer nano-size plates fortified by means of Graphene Platelets (GPLs) and resting on a Winkler-Pasternak foundation under a transverse pressure force and a temperature variation. Two graphene spreading forms dispersed through the plate thickness are studied, and the Halpin-Tsai micro-mechanics model is used to obtain the effective Young's modulus. Furthermore, the rule of mixture is employed to calculate the effective mass density and Poisson's ratio. In accordance with the first order shear deformation and von Karman theory for nonlinear systems, the kinematic equations are derived, and then nonlocal strain gradient scheme is used to reflect the effects of nonlocal and strain gradient parameters on small-size objects. Afterwards, a combined approach, kinetic dynamic relaxation method accompanied by Newmark technique, is hired for solving the time-varying equation sets, and Fortran program is developed to generate the numerical results. The accuracy of the current model is verified by comparative studies with available results in the literature. Finally, a parametric study is carried out to explore the effects of GPL's weight fractions and dispersion patterns, edge conditions, softening and hardening factors, the temperature change, the velocity of moving nanoplate and elastic foundation stiffness on the dynamic response of the structure. The result illustrates that the effects of nonlocality and strain gradient parameters are more remarkable in the higher magnitudes of the nanoplate speed.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.30 no.6
• /
• pp.1067-1078
• /
• 2020

With the development of internet technology, a lot of content is produced, and the demand for it is increasing. Accordingly, the number of contents in circulation is increasing, while the number of distributing illegal copies that infringe on copyright is also increasing. The Korea Copyright Protection Agency operates a illegal content obstruction program based on substring matching, and it is difficult to accurately search because a large number of noises are inserted to bypass this. Recently, researches using natural language processing and AI deep learning technologies to remove noise and various blockchain technologies for copyright protection are being studied, but there are limitations. In this paper, noise is removed from data collected online, and keyword-based illegal copies are searched. In addition, the same heavy uploader is estimated through profiling analysis for heavy uploaders. In the future, it is expected that copyright damage will be minimized if the illegal copy search technology and blocking and response technology are combined based on the results of profiling analysis for heavy uploaders.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.25 no.2
• /
• pp.234-239
• /
• 2021

Recently, as the installation of a large number of high-performance CCTVs for crime prevention and traffic control has increased rapidly, the problem of increasing system requirements for response to privacy infringement factors and analysis of high-definition image information transmitted from multiple cameras has been actively emerging. Accordingly, there is a need for a method for responding to privacy infringement and a method for efficiently processing surveillance images input from multiple cameras. In this paper, in order to reduce the processing cost of the input image and improve the processing speed, an integrated image is generated by grouping images input from a plurality of cameras. After analyzing the pre-generated integrated video, it detects a preset privacy event or an event that highlights interest. Depending on whether or not an event is detected, you will perform an editing operation corresponding to the event.