• 한국산학기술학회논문지
• /
• 제13권12호
• /
• pp.6046-6051
• /
• 2012

본 논문에서는 암호화 통신응용을 위한, 트랜스콘덕터에 기반한 비선형 저항으로 이루어진 카오스 추아회로를 구현하였다. 제안하는 회로는 인덕터와 커패시터의 수동소자와, MOS 트랜지스터 기반 가변저항 및 트랜스콘덕터 기반 추아 다이오드로 이루어진다. 제안하는 회로는 SPICE 모의실험결과, 시간파형, 위상특성 및 주파수 해석 등을 통하여 다양한 카오스 다이나믹스를 보여주었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.553-555
• /
• 2002

We were fabricated of rf power resisotor on AlN substrates by thick film process. The characteristics of capacitance and microwave are measured by digital LCR meter and Network analyzer(HP8532D). The results are shown that capacitances are slight greater and microwave characteristics are good values.

• 한국전기전자재료학회논문지
• /
• 제21권1호
• /
• pp.73-78
• /
• 2008

A resistor network model for the horizontal AlInGaN LED was investigated, The parameters of the proposed model are extracted from the test dies and $350{\mu}m$ LED, The center of the P-area is the optimal position of a P-electrode by the simulation using the model. Also the optimal chip size of the LED for the new target current was investigated, Comparing the simulation and fabrication result, the errors for the forward voltage and the light power are average 0,02 V, 8 % respectively, So the proposed resistor network model with the linear forward voltage approximation and the exponential light power model are useful in the simulation for the horizontal AlInGaN LED.

• E2M - 전기 전자와 첨단 소재
• /
• 제8권1호
• /
• pp.13-20
• /
• 1995

To develope a high precision TiAIN thin film resistor, TiAIN films were deposited on A1$_{2}$03 substrates by reactive planar magnetron cosputtering from Ti and Al targets in an Ar-N$_{2}$ atmosphere. The characteristics of the TiAIN thin film were controlled by changing of the R.F. power on Ti and Al targets, and the N$_{2}$ partial pressure. The high precision TiAIN thin film resistor with TCR(Temperature Coefficient of Resistance) of less than 10ppm/.deg. C was obtained under the R.F. power condition of 160(w)/240(w) to Ti and Al targets at the N$_{2}$ partial pressure of 7*10$^{-5}$ Torr. The composition of these films were investigated by XRD, SEM and EDS.

• 전기학회논문지
• /
• 제64권7호
• /
• pp.1096-1103
• /
• 2015

Electromagnetic levitation system(EMLS) is one of the well known nonlinear systems due to its high degree of nonlinearities. Moreover, when there are uncertain parameters in EMLS, it is not easy to have an accurate control of EMLS. In this paper, we first apply a standard input-output feedback linearzing controller to EMLS and investigate the possible control error caused by uncertain coil resistor. Then, as a remedy, we design and apply a robust controller using Lyapunov redesign technique to deal with this uncertain coil resistor in the system. The validity of our robust controller is verified via system analysis and experimental results.

• 전기학회논문지
• /
• 제63권12호
• /
• pp.1722-1725
• /
• 2014

An experimental investigation of COP(center of pressure) was performed using FSR(force sensing resistor) and force plate. The FSR sensor system is used as effective device to detect the movement of human body in activities of daily living. It has been shown that the FSR provides the trajectories of COP with repeatability and reliability.

• 전기학회논문지
• /
• 제62권12호
• /
• pp.1798-1802
• /
• 2013

We present a technique for measuring low resistance ranges of a decade resistor with a 4-Terminal connection. With the technique the accuracy of 0.8 % was obtained for a 1 $m{\Omega}$ resistance of the decade resistor. We suggested a proper pattern 4-Terminal measurement results with several 4-Terminal pattern and adapters. Additionally, we should that precise measurements for low resistance can be made usung a digital multimeter(DMM) only.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제55권5호
• /
• pp.250-256
• /
• 2006

Both ratio error and phase angle error in current transformer(CT) depend critically on values of CT burden. Thus, precise measurement of CT burden is very important for the evaluation of CT. A method for the measurement of CT burden has been developed by employing the portable shunt precise resistor with negligible AC-DC resistance difference less than $10^{-5}$. The burden value(value and power factor) can be calculated from resistance and reactance obtained by measuring the change of ratio error and phase angle error caused by the change of shunt resistor. The uncertainty for the method is evaluated and found to be abut 2 %.

• 반도체디스플레이기술학회지
• /
• 제14권3호
• /
• pp.57-60
• /
• 2015

Electric power in large devices is controlled by digital circuits, such as switching mode power supply. This kind of power circuits require accurate current sensor for power distribution. We studied characteristics of shunt resistor, which has many advantages for commercial application compared to Hall-effect current sensor. We applied ceramic package to the shunt resistor. Ceramic package has good thermal conductivity compared to plastic package, and this point is important for space requirement in Printed Circuit Board (PCB). Another advantage of the ceramic package is that surface mount technology (SMT) can be used for production. Our experimental results showed that the ceramic packaged resistor showed about 50% lower temperature than the plastic packaged one. Burning point and frequency characteristics are also discussed.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 춘계 학술논문 발표대회 1부
• /
• pp.39-40
• /
• 2011

The purpose of this study is to select a conductive resistor as high energy efficiency through analysis of the heating properties by induction heating. The result of this study, the heating properties is capable of weaken cementitious joint in 10~30 seconds when using the conductive resistor with wire mesh or punching metal. Although the steel is higher temperature than SUS304, SUS304's heating properties are more uniform.