• Journal of Welding and Joining
• /
• 제6권4호
• /
• pp.54-62
• /
• 1988

Major problems in welding Al-7020 include shrinkage, rpopositgy in welds and loss of strength in the heat affected zone. Thus it is important to examine the mechanical properties and reliability of welds. In this study, a series of experiments was carried out to determine the mechanical properties such as micro-hardness distribution, tensile strength, porosity and residual stress distribution of the Al-7020 weldment made by pulse-GMA welding. The resuts of the experiemnts are as folows. 1) The micro-hardness of weld metal and heat affected zone was lower than that of the base metal. 2) The tensile strength of the deposited metal was much lower than that of the base metal. 3) The porrosity in weld metal zone was negligible under the adopted conditsion of experiemnts. 4) The residual stress in the weld metal was lower than that of the heat affected zone, because the weld metal was softened. And the mciro-hardness distribution, the tensile strength and the residual stess distribution of the weldment in the as-welded condition were compared with those of the weldment after heat treatment.

• 한국지반환경공학회 논문집
• /
• 제14권5호
• /
• pp.41-47
• /
• 2013

일반적으로 입도분포가 양호하며 조밀한 흙은 공학적 성질이 우수하다. 불포화토의 공학적 성질, 즉 전단강도, 압축성, 투수성 등의 거동은 흙의 함수특성곡선과 밀접한 관계가 있다. 따라서 사질토의 입도분포 및 다짐상태와 관련있는 균등계수와 공극율이 그 흙의 함수특성곡선에 미치는 영향을 연구하는 것은 중요하다. 본 연구에서는 6개의 사질토 시료에 대하여 템페셀을 사용하여 함수특성곡선시험을 하였다. 시험결과를 Fredlund and Xing 모델식으로 최적화하여 모델식의 매개변수를 구하였고, 시료의 균등계수와 공극율이 매개변수에 미치는 영향을 조사하였다. 시료의 잔류흡수력은 시료의 공극율이 작을수록, 그리고 균등계수가 클수록 증가하였으며, 함수특성곡선의 최대경사는 시료의 균등계수와 상관없이 공극율이 작을수록 완만해짐을 알 수 있었다.

• Advances in concrete construction
• /
• 제8권4호
• /
• pp.311-320
• /
• 2019

In this study, the effect of cellulose nanocrystals (CNCs) on the fire resistance properties of fiber-reinforced cement composites was investigated. The main variables were CNCs content (0.4, 0.8 and 1.2vol.% compared with cement), steel fiber ratio, and exposure temperature (100, 200, 400, 600 and 800℃). The fire resistance properties, i.e., residual compressive strength, flexural strength, and porosity, were evaluated in relation with the exposure temperature of the specimens. The CNCs suspensions were prepared to composited dispersion method of magnetic stirring and ultra-sonication. CNCs are effective for increasing the compressive strength at high temperatures but CNCs do not seem to have a significant effect on flexural reinforcement. Porosity test result showed CNCs reduce the non-hydration area inside the cement and promote hydration.

• 해양환경안전학회지
• /
• 제3권2호
• /
• pp.13-21
• /
• 1997

This paper describes the effectiveness of laser pulse shaping in eliminating weld defects such as porosity, cracks and undercuts in pulsed Nd:YAG Laser welding. A large porosity was formed in a keyhole mode of deep penetration weld metal of any stainless steel. Solidification cracks were present in Type 303 with about 0.3%s. The conditions for the formation of porosity were determined in further detail in Type 316. With the objectives of obtaining a fundamental knowledge of formation and prevention of weld defects, the fusion and solidification behavior of a molten puddle was observed during laser spot welding of Type 310S. through high speed video photographing technique. It was deduced that cellular dendrite tips grew rapidly from the bottom to the surface, and consequently residual liquid remained at the grain boundaries in wide regions and enhanced the solidification cracking susceptibility. Several laser pulse shapes were investigated and optimum pulse shapes were proposed for the reduction and prevention of porosity and solidification cracking.

• Environmental Engineering Research
• /
• 제12권3호
• /
• pp.109-117
• /
• 2007

The characteristics of carbonaceous particles collected from the combustion of Vacuum Residue (VR) in a test furnace have been investigated. The physical and chemical characterization includes particle size, scanning electron microscopy of the surface structure, measurement of porosity, surface area and density, EDX/XRD analyses and measurement of chemical composition. The studies show that the carbonaceous VR particles are very porous and spheroidal, and have many blow-holes on the surface. The particles become smaller and more sponge-like as the reaction proceeds. The present porosity of VR particles is similar to that of cenospheres from the combustion of heavy oil, and the majority of pores are distributed in macro-pores above $0.03\;{\mu}m$ in diameter. Measurements of pore distribution and surface area showed that the macro-pores contributed most to total pore volume, whereas the micro-pores contributed to total surface area.

• 한국지반공학회지:지반
• /
• 제13권5호
• /
• pp.155-168
• /
• 1997

흙 세립자의 이탈 및 유동은 지반공학이나 지반환경공학적인 관점에서 매우 중요한 현상 중의 하나이다. 특히 지반환경공학적인 견지에서 보면 세림자가 입자유동을 하기 전에 오염물질을 흡착하기 때문에, 오염물질 정화의 방편으로 이용될 수 있다. 본 논문에서는 한국에 가장 편재해 있는 화강풍화토의 입자유동특성을 실내시험에 의해 파악하였다. 실험에 사용된 시료는 대표적인 잔류토라 할 수 있는 서을 신내동, 포이동 및 경북 안동의 시료 각각에 대하여 흐름에 대한 지반특성 치등을 측정하였다. 풍화잔적토에서의 세립분 유동특성에 가장 큰 영향을 미차는 인자는 세립자의 함량과 초기간극률 그리고 입도분포로 나타났고 입자가 이탈되기 시작하는 한계속도는 200번체 통과량에 비례 하여 감소하는 경향을 보였다. 이탈률의 변화율은 간극률에 비례하여 증가함을 보였으며 입도분 포가불량하고200번체 통과량이 적은 시료에서의 입자이탈량이 가장 크게 나타났다. 또한 실험결과를 토대로 단계별 입자유동현상을 표현하는 기본방정식을 모델링하고 유한차분법을 이용하여 해를구하므로써 흐름이 발생하는 지반구조물에서 입자유동현상이 미치는 영향을 파악할 수 있는 토대를 마련하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제28권8호
• /
• pp.1270-1278
• /
• 2004

This paper describes the effectiveness of laser pulse shaping in eliminating weld defects such as porosity, cracks and undercuts in pulsed Nd:YAG laser welding. A large porosity was formed in a keyhole mode of deeply penetrated weld metal of any stainless steel. Solidification cracks were present in STS 310S with above 0.017%P and undercuts were formed in STS 303 with about 0.3%S. The conditions for the formation of porosity were determined in further detail in STS 316. With the objectives of obtaining a fundamental knowledge of formation and prevention of weld defects, the fusion and solidification behavior of a molten puddle was observed during laser spot welding of STS 310S through a high speed video photographing technique. It was deduced that cellular dendrite tips grew rapidly from the bottom to the surface, and consequently residual liquid remained at the grain boundaries in wide regions and enhanced the solidification cracking susceptibility. Several laser pulse shapes were investigated and optimum pulse shapes were proposed for the reduction and prevention of porosity and solidification cracking.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1996년도 자동차부품 제작기술의 진보
• /
• pp.35-46
• /
• 1996

The powder forging process offers beneficial material utilization as well as the minimization of finishing operations over that of conventionally forged rods. In the present work, the sintering behavior of Fe-2Cu-0.6C-0.35MnS, optimum preform design and forgeability of various forging conditions were investigated. This data were generated using a newly proposed sub-scaled con-rod specimen developed specifically to simulate the powder forging process. The results of present work, powder perform is so difficult to flow material into die cavity and mass flow has no effect on improving the strength. And, applied force to increase density of the specimen flowed material is greater than that of all repessing mode. On the contrary, the specimen flowed material became increased hardness of inside in contrast with all repressing mode, but the tensile strength were decreased with residual porosity in surface. Due to material flow characteristic of powder preform, the section of lower density in powder preform became also lower density in forged con-rod. So, preform design is very important in manufacturing powder forged connecting rod.

• 한국세라믹학회지
• /
• 제44권7호
• /
• pp.381-386
• /
• 2007

A porous reaction bonded silicon carbide (RBSC) was fabricated by a molten Si infiltration method. The porosity and flexural strength of porous RBSC fabricated in this study were dependent upon the amount of carbon source used in the SiC/carbon preform as well as the amount of Si infiltrated into the SiC/carbon preform. The porosity and flexural strength of porous RBSC were in the range of $20 vo1.{\sim}49 vo1.%$ and $38{\sim}61 MPa$, respectively. With increase of carbon contents and molten Si for infiltration, volume fraction of the pores was gradually decreased, and flexural strength was increased. The porous RBSCs fabricated with the same amount of molten Si show less residual Si around neck with increase of carbon source, as well as a new SiC was formed around neck which resulted in the decreased porosity and improvement of the flexural strength. In addition, decrease of the porosity and increase of the flexural strength were also obtained by increase of the amount of molten Si with the same amount of carbon source. However, it was found that the flexural strength of porous RBSC depends on the porosity rather than the amount of the newly formed SiC in neck phase between SiC particles used as a starting material.

• 지질공학
• /
• 제15권1호
• /
• pp.29-39
• /
• 2005

지반오염을 조사하기 위해서는 시추작업을 통하여 시료를 채취하는 방법이 일반적이지만, 실시간으로 원위치에서 다양한 오염물질들의 오염 도 변화를 체계적으로 모니터링 하는 것은 대단히 어렵다. 본 연구에서는 frequency Domain Reflectometry (FDR) 장비를 고안하여 지반의 유류오염을 파악하기 위한 유전율 측정법의 실험적 접근을 시도하였다. 구체적으로 포화 및 불포화 매질에 대한 유류 오염도 측정 및 체적함수비 (θ/sub w/)와 체적 유류비 ( θ/sub al/)의 관계에서 유전율 상수 반응에 따른 매질의 유류 오염도 등의 측정 가능성을 실내 시험을 통해 검토하였다. 뿐만 아니라 실내 칼럼 시험을 수행하여 포화 매질 내에서 유류 거동 특성을 각기 설치된 FDR 측정 센서를 이용해 모니터링하여 포화 매질의 유효공극률과 유류 잔류비를 측정하였다. 그 결과 초기 공극률 0.40으로 제작된 포화 매질의 유효공극률은 약 0.35로 공극률 대비 약 87.5% 범위내에 존재함을 알 수 있었으며, 유류 잔류비는 약 62.5% 정도로 매우 높게 나타났다.