• Journal of Welding and Joining
• /
• v.21 no.6
• /
• pp.46-54
• /
• 2003

The thermal response of electronic assemblies during forced convection-infrared reflow soldering is studied. Soldering for attaching electronic components to printed circuit boards is performed in a process oven that is equipped with porous panel heaters, through which air is injected in order to dampen temperature fluctuations in the oven which can be established by thermal buoyancy forces. Forced convection-infrared reflow soldering process with air injection is simulated using a 2-dimensional numerical model. The multimode heat transfer within the reflow oven as well as within the electronic assembly is simulated. Parametric study is also performed to study the effects of various conditions such as conveyor speed, blowing velocity, and electronic assembly emissivity on the thermal response of electronic assemblies. The results of this study can be used in the process oven design and selecting the oven operating conditions to ensure proper solder melting and solidification.

• Journal of the Korean institute of surface engineering
• /
• v.36 no.5
• /
• pp.373-378
• /
• 2003

With increasing environmental concerns, application of lead-free solder and fluxless soldering process have been taken attention from the electronic packaging industry. Plasma treatment is one of the soldering methods for the fluxless soldering, and it can prevent environmental pollution cased by flux. On this study fluxless soldering process under $Ar-H_2$plasma using lead free solders such as Sn-3.5 wt%Ag, Sn-3.5 wt%Ag-0.7 wt%Cu and Sn-37%Pb for a reference was investigated. As the plasma reflow has higher soldering temperature than normal air reflow, the effects of UBM(Under Bump Metallization) thickness on the interfacial reaction and bonding strength can be critical. Experimental results showed in case of the thin UBM, Au(20 nm)/Cu(0.3 $\mu\textrm{m}$)/Ni(0.4 $\mu\textrm{m}$)/Al(0.4 $\mu\textrm{m}$), shear strength of the soldered joint was relatively low as 19-27㎫, and it's caused by the crack observed along the bonded interface. The crack was believed to be produced by the exhaustion of the thin UBM-layer due to the excessive reaction with solder under plasma. However, in case of thick UBM, Au(20 nm)/Cu(4 $\mu\textrm{m}$)/Ni(4 $\mu\textrm{m}$)/Al(0.4 $\mu\textrm{m}$), the bonded interface was sound without any crack and shear strength gives 32∼42㎫. Thus, by increasing UBM thickness in this study the shear strength can be improved to 50∼70%. Fluxed reflow soldering under hot air was also carried out for a reference, and the shear strength was 48∼52㎫. Consequently the fluxless soldering with plasma showed around 65∼80% as those of fluxed air reflow, and the possibility of the $Ar-H_2$ plasma reflow was evaluated.

• Journal of Welding and Joining
• /
• v.15 no.6
• /
• pp.105-115
• /
• 1997

A numerical study is performed to predict the thermal response of a detailed card assembly during infrared reflow soldering. The card assembly is exposed to discontinuous infrared panel heater temperature distributions and high radiative/convective heating and cooling rates at the inlet and exit of the oven. The convective, radiative and conduction heat transfer within the reflow oven as well as within the card assembly are simulated and the predictions illustrate the detailed thermal responses. The predictions show that mixed convection plays an important role with relatively high frequency effects attributed to buoyancy forces, however the thermal response of the card assembly is dominated by radiation. The predictions of the detailed card assembly thermal response can be used to select the oven operating conditions to ensure proper solder melting and minimization of thermally induced card assembly tresses and warpage.

• 유체기계공업학회:학술대회논문집
• /
• 2006.08a
• /
• pp.561-564
• /
• 2006

Because of new requirements related to the employment of SMT(Surface Mounting Technology) manufacturing and the diversity of components on high density PCB(printed circuit boards), Thermal control of the reflow process is required in oder to achieve acceptable yields and reliability of SMT assemblies. Accurate control of the temperature distribution during the reflow process is one of the major requirements, especially in lead-free assembly. This study has been performed for reflow process using the commercial CFD tool(Fluent) for predicting flow and temperature distributions. There was flow recirculation region that had a weak point in the temperature uniformity. Porous plate was installed to prevent and minimize flow recirculation region for acquiring uniform temperature in oven. This paper provided design concept from CFD results of the steady state temperature distribution and flow field inside a reflow oven.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.23 no.6
• /
• pp.574-581
• /
• 2020

This paper describes the stacking effect for Ceramic Column Grid Array(CCGA) packages used for satellites. Reflow Soldering Process suitable for CCGA package with back structure was set as the process development goal to meet European Cooperation for Space Standardization(ECSS) standard. After analyzing the stacking effect according to the type of CCGA, it is verified by applying it to the CCGA Reflow Soldering Process. In order to confirm the validity of the staking effect analyzed in terms of vibration and thermal characteristics, it is verified through actual specimen production. It analyzes the cause of crack occurrence in the CCGA package and estimates the crack generation point using previously acquired inspection data.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.3
• /
• pp.35-39
• /
• 2020

Nonwet (Head in Pillow) defect is one of the defects in SMT (surface mount technology) process, the defect is caused by several factors, such as solder paste misalignment, reflow condition, package warpage and package ball size. This paper focused on ① reflow condition ② package ball & solder paste misalignment ③ package ball size for nonwet experiment. The first, on the case of reflow condition, there would be high risk of nonwet defect when the soldering time was increased, but N₂ was adopted to reflow process, there could be no or low risk of nonwet defect because of oxidation barrier control. And when the contact depth between Solder ball and solder paste was below 20 ㎛, there could be high risk of nonwet defect. Also smaller package ball would have low risk of nonwet defect.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2000.04a
• /
• pp.17-17
• /
• 2000

The issue of reflow profiling continues to be a complex topic. The pains often associated with profiling can be reduced greatly if certain guidelines are followed and if there is a strong understanding of the variables that can be encountered during the reflow process. This paper shall discuss the appropriate guidelines and trouble shooting methods for reflow profiling, and in particular shall focus upon the benefits of implementing the linear ramp-to-spike profile. Delta T(T) is defined as the variation of temperature found on an assembly during the reflow process. Too large of a T can result in soldering defects, so to combat T a Ramp-Soak-Spike(RSS) reflow profile often is utilized. However, when using a newer-style reflow oven, the T often is minimized or eliminated, thus, the soak zone of the reflow profile becomes an unnecessary step. Because of this, the implementation of a linear Ramp-To-Spike(RTS) reflow profile should be considered. Benefits such as reduced energy costs, reduced solder defects, increased efficiency, improved wetting, and a simplification of the reflow profile process may be experienced when using the RTS profile. Included in this paper are the suggested process parameters for setting up the RSS and RTS profiles and the chemical and metallurgical reactions that occur at each set point of these profiles. The paper concludes with a discussion and pictures of several profile-related defects. Each of these defects is described, analyzed, and instructions are given for troublshooting these defects.

• Journal of Korea Foundry Society
• /
• v.22 no.1
• /
• pp.35-41
• /
• 2002

To improve the reliability of solder joints, a composite solder which consists of solder matrix and intermetallic reinforcements was manufactured by a new method. The cast ingot of Sn-6.9Cu-2.9Ag alloy had primary Cu6Sn5 intermetallics in the form of dendrites. After rolling the ingot, the intermetallic dendrites were crushed into fine particles and distributed uniformly throughout the solder matrix. As the rolled strips became thinner, the average size of the crushed particles reached a critical size which did not decrease any more by further rolling. The critical size was nearly the same as the average width of intermetallic dendrite trunk. The crushed intermetallic particles did not melt and remained in solid state during reflow soldering due to their high meltingterm-perature. The coarsening and gravitational segregation of the particles were observed during reflow soldering.

• Journal of the Semiconductor & Display Technology
• /
• v.5 no.3 s.16
• /
• pp.29-32
• /
• 2006

Because of new requirements related to the employment of SMT(Surface Mounting Technology) manufacturing and the diversity of components on high density PCB(Printed Circuit Boards), Thermal control of the reflow process is required in order to achieve acceptable yields and reliability of SMT assemblies. Accurate control of the temperature distribution during the reflow process is one of the major requirements, especially in lead-free assembly. This study has been performed for reflow process using the commercial CFD(Computational Fluid Dynamics) tool for predicting flow and temperature distributions. Porous plate was installed to prevent leakage flow which was one of the major problem of temperature uniformity in the reflow process. There is a separation region where the flow is turned. Outside wall made of porous plate is to prevent and minimize separation region for acquiring uniform temperature during operation. This paper provided design concept from CFD results of the steady state temperature distribution and flow field inside a reflow oven.

• Progress in Superconductivity and Cryogenics
• /
• v.12 no.2
• /
• pp.9-12
• /
• 2010

A lamination system using reflow soldering was developed to enhance the mechanical properties of high temperature superconductor (HTS) tape. The laminated coated conductor tape was fabricated using the continuous lamination process. The mean, maximum, and minimum tensile loads in a T-peel test of the laminated coated conductor were 9.9 N, 12.5 N, and 7.6 N, respectively. The critical current ($I_c$) distributions of the non-laminated and laminated coated conductor were compared using anon-contact Hall probe method. The transport $I_c$ nearly matched the non-contact $I_c$; however, some degraded Ic regions were found on the length of 800 cm of laminated coated conductor. We confirmed that the cause of the partially degraded $I_c$ was due to an increase in line tension by (1) solidification induced by a change of composition that usually occurs in molten brass (Cu, Zn) in solder, or (2) non-homogeneity of the thickness of the coated conductor or metal tapes. We suggest that reflow soldering is a promising method for reinforced HTS tape if the controlling solder thickness and lamination guide are modified.