• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.6
• /
• pp.1127-1134
• /
• 2002

The present paper provides an engineering J estimation equation for surface cracked plates under combined bending and tension. The proposed equation is based on the reference stress approach, and the most relevant normalising loads to define the reference stress for accurate J estimations are given for surface cracked plates under combined bending and tension. Comparisons with J results from extensive 3-D FE analyses, covering a wide range of crack geometry, plate geometry and loading combination, show overall good agreement not only at the deepest point but also at arbitrary points along the crack front. for pure tension, agreement between the estimated J and the FE results is excellent, even at the surface point. On the other hand, for pure bending and combined bending and tension, the estimated J values become less accurate for locations close to the surface point. Thus the results in this paper will be useful to assess short-term fracture or low cycle fatigue of surface defects in plates under combined bending and tension.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.125-130
• /
• 2003

This paper provides approximate J estimates for off-centred, circumferential through-wall cracks in cylinders under bending. The proposed method is based on the reference stress approach, where the dependence of elastic and plastic influence functions of J on the cylinder/crack geometry, the off-centred angle and strain hardening is minimised through the use of a proper normalising load. Based on published limited FE results for off-centred, circumferential through-wall cracks under bending, such normalising load is found, based on which the reference stress based J estimates are proposed for more general cases, such as for a different cylinder geometry. Comparison of the estimated J with extensive FE J results shows overall good agreements for different crack/cylinder geometries which provides sufficient confidence in the use of the proposed method to fracture mechanics analyses of off-centred circumferential cracks. Furthermore, the proposed method is simple to use, giving significant merits in practice.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1766-1771
• /
• 2007

This paper presents plastic limit loads and approximate J-integral estimates for circumferential part-through surface crack at the interface between elbows and pipes. Based on finite element limit analyses using elastic-perfectly plastic materials, plastic limit moments under in-plane bending are obtained and it is found that they are similar those for circumferential part-through surface cracks in the center of elbow. Based on present FE results, closed-form limit load solutions are proposed. Welds are not explicitly considered and all materials are assumed to be homogeneous. And the method to estimate the elastic-plastic J-integral for circumferential part-through surface cracks at the interface between elbows and straight pipes is proposed based on the reference stress approach, which was compared with corresponding solutions for straight pipes.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.29 no.10 s.241
• /
• pp.1399-1406
• /
• 2005

Recently authors have proposed a new method to estimate failure strength of a pipe with local wall thinning subject to either internal pressure or global bending. The proposed method was based on the equivalent stress averaged over the minimum ligament in the locally wall thinned region, and the simple scheme to estimate the equivalent stress in the minimum ligament was proposed, based on the reference stress concept. This paper extends the new method to combined internal pressure and global bending. The proposed method is validated against FE results for various geometries of local wall thinning under combined loading. The effect of internal pressure is also investigated in the present study. Comparison of maximum moments, predicted according to the proposed method, with published full-scale pipe test data fur locally wall-thinned pipes under combined internal pressure and global bending, shows good agreement.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.1
• /
• pp.47-52
• /
• 2011

In this paper, we describe the development of a finite-element model for seismic qualification. This paper presents finite-element analysis model of the electronic enclosure to be used at Arkansas nuclear power plant, USA. The verified model predicts natural frequencies within 5% error for all major modes below 50 Hz. The finite element lumped mass approach and the finite element stiffness approach using the COSMOSM finite element code is applied for static, eigenvalue, and dynamic analyses of the mathematical model of this system. The FEM model indicates that the stress levels corresponding to the specified loading conditions are below the allowable stress levels that have been specified in the AISC Code. The findings conclude that the electronic enclosure will withstand the seismic levels stated in the reference documents.

• Journal of the Korean Society of Safety
• /
• v.29 no.5
• /
• pp.88-96
• /
• 2014

Each year, it seems inevitable that major accidents will occur on construction sites. Industrial accidents, sometimes involving foreign laborers, have been constantly increasing. Construction laborers have higher hazard rates and higher work intensity than other industries, which means that they experience more job stress, as a result of the subcontracting structure. Therefore, this study performed an influence factor analysis on job stress and its relevance to industrial accidents involving Korean and foreign construction laborers, and proposed its effectiveness with the job stress and construction accident management measures based on the results of those. A questionnaire to measure job stress was performed targeting Korean and foreign laborers, and the results were analyzed. The results of this study can be utilized as important reference materials in efforts to reduce the job stress of foreign laborers on construction sites, and can be expected to contribute to preventing construction accidents related to job stress in the future.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.2 no.4
• /
• pp.200-210
• /
• 2010

In this paper, different evaluation methods of Hot Spot Stresses (HSS) have been applied to four different welded structure details in order to compare them and to illustrate their differences. The HSSs at failure-critical locations were calculated by means of a series of finite element analyses. There was good overall agreement between calculated and experimentally determined HSS on the critical locations. While different methods and procedures exist for the computation of the structural hot-spot stress at welded joints, the recommendations within the International Institute of Welding (IIW) guideline concerning the 'Hot Spot Stress' approach were found to give good reference stress approximations for fatigue-loaded welded joints. This paper recommends and suggests an appropriate finite element modeling and hot spot stress evaluation technique based on round-robin stress analyses and experimental results of several welded structure details.

• International Journal of Naval Architecture and Ocean Engineering
• /
• v.13 no.1
• /
• pp.379-395
• /
• 2021

For the complicated structural details in ships and offshore structures, the traditional hotspot stress approaches are known to be sensitive to the element variables of element topologies, sizes, and integration schemes. This motivated to develop a new approach for predicting reasonable hotspot stresses, which is less sensitive to the element variables and easy to be implemented the real marine structures. The three-point bending tests were conducted for the longitudinal attachments with the round and rectangular weld toes. The tests were reproduced in the numerical simulations using the solid and shell element models, and the simulation technique was validated by comparing the experimental stresses with the simulated ones. This paper considered three hotspot stress approaches: the ESM method based on surface stress extrapolation, the Dong's method based on nodal forces along a weld toe, and the proposed method based on nodal forces perpendicular to an imaginary vertical plane at a weld toe. In order to study the element sensitivities of each method, 16 solid element models and 8 shell element models were generated under the bending and tension loads, respectively. The element sensitivity was analyzed in terms of Stress Concentration Factors (SCFs) in viewpoints of two statistical quantities of mean and bias with respect to the reference SCFs. The average SCFs predicted by the proposed method were remarkably in good agreement with the reference SCFs based on the experiments and the ship rules. Negligibly small Coefficients of Variation (CVs) of the SCFs, which is measure of statistical bias, were drawn by the proposed method.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.4
• /
• pp.981-989
• /
• 1995

A new weight function approach to determine SIF(stress intensity factor) using single-layer potential has been presented. The crack surface displacement field was represented by one boundary integral term whose kernel was modified from Kelvin's fundamental solution. The proposed method enables the calculation of SIF using only one SIF solution without any modification for the crack geometries symmetric in two-dimensional plane such as a center crack in a plate with or without an internal hole, double edge cracks, circumferential crack or radial cracks in a pipe. The application procedure to those crack problems is very simple and straightforward with only one SIF solution. The necessary information in the analysis is two reference SIFs. The analysis results using present closed-form solution were in good agreement with those of the literature.

• Safety and Health at Work
• /
• v.4 no.2
• /
• pp.95-99
• /
• 2013

Background: Work-related stress is one of the major causes of occupational ill health. In line with the regulatory framework on occupational health and safety (OSH), adequate models for assessing and managing risk need to be identified so as to minimize the impact of this stress not only on workers' health, but also on productivity. Methods: After close analysis of the Italian and European reference regulatory framework and workrelated stress assessment and management models used in some European countries, we adopted the UK Health and Safety Executive's (HSE) Management Standards (MS) approach, adapting it to the Italian context in order to provide a suitable methodological proposal for Italy. Results: We have developed a work-related stress risk assessment strategy, meeting regulatory requirements, now available on a specific web platform that includes software, tutorials, and other tools to assist companies in their assessments. Conclusion: This methodological proposal is new on the Italian work-related stress risk assessment scene. Besides providing an evaluation approach using scientifically validated instruments, it ensures the active participation of occupational health professionals in each company. The assessment tools provided enable companies not only to comply with the law, but also to contribute to a database for monitoring and assessment and give access to a reserved area for data analysis and comparisons.