• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.6
• /
• pp.1133-1138
• /
• 2010

We have developed an imaging radiometer system at W-band. The system consists of lens, reflector, 30-ch receiver array, scanner, and signal processor. One receiver consists of a dielectric rod antenna, a balun, LNA(low noise amplifier) and a detector. The system configuration requirements are described. Finally, we represent radiometer images to obtain through clouds, smoke, dust, and other obstructions which render visible and IR systems ineffective.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.1
• /
• pp.52-59
• /
• 2009

In modern radars, dynamic range requirements far severed due to high CNR(Clutter-to-Noise Ratio) environment operation scenario. ADC spurious signal restricted the required dynamic range. In this paper, receiver gain of active phased array radar dependent on ADC nonlinear characteristic was analyzed. Within limited scope of ADC SFDR which blocks required system dynamic range, ADC dynamic range reaches trade-off with ADC SNR loss. Comparing antenna stage output noise voltage to that of ADC input, receiver gain was mathematically analyzed. Finally the whole contents were explained from the application example.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1222-1227
• /
• 2005

In this paper, an efficient scheme of the adaptive notch filter is presented for rejecting the narrow bandwidth interferences(NBI) in GPS receiver. Designed is the lattice IIR double notch filter for more efficient suppression of the NBI with less computational complexity. The algorithm is of recursive prediction error form and uses a special constrained model of IIR with a minimal number of parameters. This paper chooses seven different jamming scenarios including one without jamming for evaluating the proposed filter algorithm. The simulation results to the jamming scenarios show that the proposed algorithm adjusts the double notch filter effectively for the given JSR, and provides better SNR than the conventional algorithms. Finally, it is shown that the advantages of the proposed filter algorithm can range as high as JSR 79dB in time domain processing. Also, the ADNF(adaptive double notch filter) guarantees that more than SNR 10dB of GPS receiver can be always maintained. In conclusion, there is enough evidence to believe that the proposed algorithm will perform quite well for removing interference signals.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.1082-1087
• /
• 2019

In this study, ECG signal amplifier, wireless transmitter/receiver circuit, signal processing filter circuit and A/D converter circuit design required for the development of small sized ECG module for wireless transmission/ reception were performed. In order to verify the performance of ECG sensors, the measurement was performed from 1 m to 3 m to measure the signal noise ratio according to the gateway distance. Experimental results showed that the signal noise ratio at 2 m distance was 17.18 dB on average, which fulfilled the requirements for commercialization. The experimental results obtained in this study are expected to contribute to the low cost, high efficiency mobile health field where remote monitoring diagnosis can be applied to small biometric devices for chronic disease management.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.05a
• /
• pp.109-114
• /
• 2003

Wireless communication systems are inevitable for efficient underwater activities. Because of the poor propagation characteristics of light and electromagnetic waves, acoustic waves are generally used for the underwater wireless communication. Although there are many kinds of information type, visual images take an essential role especially for search and identification activities. For this reason, we developed an acoustic-based underwater image transmission system under a dual use technology project supported by MOCIE (Ministry of Commerce, Industry and Energy). For the application to complicated and time-varying underwater environments all-digital transmitter and receiver systems are investigated. Array acoustic transducers are used at the receiver, which have the center frequency of 32kHz and the bandwidth of 4kHz. To improve transmission speed and quality, various algorithms and systems are used. The system design techniques will be discussed in detail including image compression/ decompression system, adaptive beam- forming, fast RLS adaptive equalizer, ${\partial}/4$ QPSK (Quadrilateral Phase Shift Keying) modulator/demodulator, and convolution coding/ Viterbi. Decoding.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.1
• /
• pp.139-146
• /
• 2017

The ISDB-T(Integrated Service Digital Broadcasting Terrestrial) can be used in the multipath and impulsive noise, also it provide good performance over mobile reception environment since it use the OFDM(Orthogonal Frequency Division Multiplexing) based transmission technology and time interleaving technology. One segment and full segment are divided according to the number of the assigned segment. And one-segment broadcasting receiver can design and implement without high levels of technology than the full-segment broadcasting receiver using 64QAM(64 Quadrature Amplitude Modulation) since it uses QPSK(Quadrature Phase Shift Keying) modulation/demodulation. However, it has a constraint in the display size and resolution due to data-rate limits. In this paper, we design and implementation of full-segment ISDB-T receiver module which support HD resolution for set-top box, digital TV, navigation. In experimental results, the implemented full-segment ISDB-T receiver module was satisfactory for all of the desired functions.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.1
• /
• pp.68-74
• /
• 2003

This paper describes the design and the test results of the receiver-downconverter module for a Ka-band Satellite Payload. The developed module is not only a downconverter that convert the signal of 30.6 GHz∼31.0 GHz to the signal of 20.8 GHz∼21.2 GHz but also is a receiver that has the function of low noise amplification in the front stage. It has been fabricated and tested by the qualified satellite component manufacturing process and it shows the best performance of the receiver-downconverter modules operating at Ka-band frequency up to date. The module has the performance of 1.9 dB-NF, 55 dB-Gain, and 58 dBc-C/I3 fur the two tone signals of -59 dBm input power respectively at ambient temperature. It is a small and light module with the size of 93 mm${\times}$84 mm${\times}$26 mm and the weight of 240 g.

• Journal of Advanced Navigation Technology
• /
• v.18 no.4
• /
• pp.312-318
• /
• 2014

The altitudes of GEO satellites are higher than those of GPS satellites. Therefore the visibility and the received power of GPS signals are totally different from those of the users near the Earth's surface. In this study, we analyzed the visibility of GPS signals received on GEO satellites. And we also developed a software GPS receiver that works on GEO satellites using CCMDB algorithm which is a weak signal receiver algorithm. GPS signals received on a GEO satellite are generated by a commercial hardware GPS simulator and used for the verification of the developed software GPS receiver. The mean 3D position and velocity error are calculated as 165.636 m and 0.5081 m/s.

• Journal of Positioning, Navigation, and Timing
• /
• v.5 no.1
• /
• pp.11-20
• /
• 2016

In this paper, a system that can collect GPS L1 C/A, GLONASS G1, and BDS B1I signals with single front-end receiver was implemented using a universal software radio peripheral (USRP) and its performance was verified. To acquire the global navigation satellite system signals, hardware was configured using USRP, antenna, external low-noise amplifier, and external oscillator. In addition, a value of optimum local oscillator frequency was selected to sample signals from three systems with L1-band with a low sampling rate as much as possible. The comparison result of C/N0 between the signal collection system using the proposed method and commercial receiver using double front-end showed that the proposed system had 0.7 ~ 0.8dB higher than that of commercial receiver for GPS L1 C/A signals and 1 ~ 2 dB lower than that of commercial receiver for GLONASS G1 and BDS B1I. Through the above results, it was verified that signals collected using the three systems with a single USRP had no significant error with that of commercial receiver. In the future, it is expected that the proposed system will be combined with software-defined radio (SDR) and advanced to a receiver that has a re-configuration channel.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2002.03a
• /
• pp.221-228
• /
• 2002

Thickness of concrete lining, voids at the back of lining or shotcrete are very important elements for inspecting the safety of tunnels. Therefore, the inspection of tunnel lining structure means to investigate the inner layer boundaries of the structure. For this purpose, seismic reflection survey is the most desirable method if it works in good conditions. However, the conventional seismic reflection method can not be properly used for investigating thin layers in the lining structure. In other words, to detect the inner boundaries, it is desirable for the wavelength of source to be less than the thickness of each layer and for the receiver to be capable of detecting high frequency(ultrasonic) signals. To this end, new appropriate source and receiver devices should be developed above all for the ultrasonic reflection survey. This paper deals primarily with the development of source and receiver devices which are essential parts of field measuring system. Interests are above all centered in both the radiation pattern, energy, frequency content of the source and the directional sensitivity of the receiver. With these newly devised ones, ultrasonic physical modeling has been performed on 3-D physical model composed of bakelite, water-proof and concrete, The measured seismograms showed a clear separation of wave arrivals reflected from each layer boundary. Furthermore, it is noteworthy that reflection events from the bottom of concrete below water-proof could be also observed. This result demonstrates the usefulness of the both devices that can be applied to benefit the ultrasonic reflection survey. Future research is being focus on dealing with at first an optimal configuration of source and receiver devices well coupled to tunnel wall, and further an efficient data control system of practical use.