• 한국콘텐츠학회논문지
• /
• 제16권1호
• /
• pp.52-59
• /
• 2016

동절기에 타설되는 대부분의 콘크리트 구조물에서 가설 초기단계에서의 양생방법의 선정은 매우 중요한 요소이다. 동절기에는 초기균열과 강도저하를 방지하기 위하여 열선과 조강시멘트를 이용한 발열양생방법을 주로 적용하게 된다. 하지만 그 적용기법의 단순화 및 경험적 판단에의 의존으로 인하여 대부분의 건설현장에서 최적의 양생방법을 선정하지 못하고 있는 실정이다. 이에 따라 본 논문에서는 비정상상태의 열전달 해법을 통하여 가장 적절한 열선의 가열온도, 기간, 열선 배치간격을 선정하는 평가 알고리즘을 개발하였다. 이를 위하여 관리 매개변수에 주안점을 둔 구조해석 시스템을 통한 사용자 중심의 OOP 루틴을 적용하였다. 본 시스템에서는 입력모듈, DB 모듈, DB저장 모듈, 해석모듈 및 결과분석모듈로 구분하였으며, 각 모듈간의 연계는 visual c# 루틴으로 처리하였다. 또한 그래픽 인터페이스와 DB 테이블은 사용자 편의성을 고려하여 개발하였다.

• 대한금속재료학회지
• /
• 제50권12호
• /
• pp.891-896
• /
• 2012

Nanopowders of MgO and $TiO_2$ were made by high energy ball milling. The rapid synthesis and sintering of the nanostructured $MgTiO_3$ compound was investigated by the high-frequency induction heated sintering process. The advantage of this process is that it allows very quick densification to near theoretical density and inhibition grain growth. Nanocrystalline materials have received much attention as advanced engineering materials with improved physical and mechanical properties. As nanomaterials possess high strength, high hardness, excellent ductility and toughness, undoubtedly, more attention has been paid for the application of nanomaterials. A highly dense nanostructured $MgTiO_3$ compound was produced with simultaneous application of 80 MPa pressure and induced current within 2 min. The sintering behavior, gain size and mechanical properties of $MgTiO_3$ compound were investigated.

• 대한금속재료학회지
• /
• 제49권3호
• /
• pp.231-236
• /
• 2011

Nanopowder of $Fe_2O_3$, Al, Cr and Si was fabricated by high energy ball milling. A dense nanostuctured $A_2O_3$ and $6.06Fe_{0.33}Cr_{0.16}Al_{0.23}Si_{0.29}$ composite was simultaneously synthesized and consolidated using high frequency induction heated sintering method within 1 minute from mechanically activated powders of $Fe_2O_3$, Al, Cr and Si. The grain sizes of $Al_2O_3$ and $Fe_{0.33}Cr_{0.16}Al_{0.23}Si_{0.29}$ in composite are 80 and 18 nm, respectively.

• 한국균학회지
• /
• 제49권4호
• /
• pp.455-467
• /
• 2021

Macrofungi are valuable resources as novel drug candidates, new biomaterials, and edible materials. Recently, genetic approaches pertaining to macrofungi have been continuously growing for their identification, molecular breeding, and genetic engineering. However, purification and amplification of fungal DNA is challenging because of the rigid cell wall and presence of PCR inhibitory metabolites. Here, we established a direct PCR method to provide a rapid and efficient method for PCR-grade macrofungal DNA preparation applicable to both conventional PCR and real-time PCR. We first optimized the procedure of lysis and PCR using the mycelia of Lentinula edodes, one of the most widely consumed macrofungal species. Lysates prepared by neutralizing with (NH₄)₂SO₄ after heating the mycelia in a mixture of TE buffer and KOH at 65℃ for 10 min showed successful amplification in both conventional and real-time PCR. Moreover, the addition of bovine serum albumin to the PCR mixture enhanced the amplification in conventional PCR. Using this method, we successfully amplified not only internal transcribed spacer fragments but also low-copy genes ranging in length from 500 to 3,000 bp. Next, we applied this method to 62 different species (54 genera) of macrofungi, including edible mushrooms, such as Pleurotus ostreatus, and medicinal mushrooms such as Cordyceps militaris. It was found that our method is widely applicable to both ascomycetes and basidiomycetes. We expect that our method will contribute to accelerating PCR-based approaches, such as molecular identification, DNA marker typing, gene cloning, and transformant screening, in macrofungal studies.

• 한국결정성장학회지
• /
• 제8권3호
• /
• pp.508-512
• /
• 1998

마이크로파(2.45GHz) 에너지를 이용한 소결법으로 $1100^{\circ}C$~$1300^{\circ}C$의 온도범위에서 반도체 세라믹스인 $Mn_3O_4{\cdot}Co_3O_4{\cdot}3NiO$ 조성의 NTC 서미스터를 소결하였으며, 그 전기적 특성을 조사하였다. 소결온도가 높아질수록 소결밀도가 높은 치밀한 소결체를 얻을 수 있었으며, 25~$85^{\circ}C$ 범위의 온도변화에 따른 전기저항변화 특성으로부터 구한 비저항 $B_{25^{\circ/85^{\circ}}$ 정수는 3100~3200K이었다. 마이크로파 하이브리드, 소결법으로 소결된 시편과 일반소결법으로 소결된 시편을 비교하면 소결특성과 전기적물성에서 비슷한 결과를 얻을 수 있었다. 마이크로파 에너지를 이용한 소결공정은 20분 안에 완료되는 짧은 시간의 급속소결법으로 공정 시간과 에너지를 크게 절감할 수 있었다.

• 한국산학기술학회논문지
• /
• 제18권7호
• /
• pp.17-25
• /
• 2017

최근에 LED나 OLED와 같은 조명용 소자의 온도 상승에 따른 문제점을 개선하기 위하여 전기 도금 방법을 사용하여 제작한 두께가 두꺼운 금속 필름을 heat sink로 사용하고 있다. Cu 필름과 같은 두꺼운 금속 필름은 습식 방법인 전기 도금으로 제작하여 주로 소자의 방열판으로 사용되어 왔으나 건식의 증착 방법을 이용한 수 백 ${\mu}m$의 Cu 금속 필름에 대한 필요성이 요구되고 있다. 본 연구에서 설계 제작된 유도 가열 방식의 Cu 필름 증착 장비는 가열부가 세라믹 도가니 히터 부분과 세라믹 도가니 부분으로 분리된 이중 구조의 heating 방식을 채택하여 열 손실을 최소화 하고 보온 효과를 극대화시켰다. 또한 유도 가열 방식으로 초고속의 필름 증착 속도를 구현하였다. 그리고 열전도도가 높고 안정적인 두꺼운 Cu 필름 증착기술을 확보하고 최적화 하여 $1000{\AA}/s$의 증착율로 $100{\mu}m$의 필름을 증착 하였으며 ~2.0% 이내의 두께 균일도를 얻었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.50-50
• /
• 2009

In this paper, the plasma doping is performed on p-type wafers using $PH_3$ gas(10 %) diluted with He gas(90 %). The wafer is placed in the plasma generated with 200 W and a negative DC bias (1 kV) is applied to the substrate for 60 sec under no substrate heating. the flow rate of the diluted $PH_3$ gas and the process pressure are 100 sccm and 10 mTorr, respectively. In order to diffuse and activate the dopant, annealing process such as rapid thermal annealing (RTA) is performed. RTA process is performed either in $N_2$, $O_2$ or $O_2+N_2$ ambient at $900{\sim}950^{\circ}C$ for 10 sec. The sheet resistance is measured using four point probe. The shallow n+/p doping profiles are investigated using secondary ion mass spectromtry (SIMS). The analysis of crystalline defect is also done using transmission electron microscopy (TEM) and double crystal X-ray diffraction (DXRD).

• 한국세라믹학회지
• /
• 제56권6호
• /
• pp.583-588
• /
• 2019

Silicon carbide (SiC) fiber mats generate large amounts of heat through microwave interactions and are used as heating elements in rapid heat treatment furnaces. However, SiC fibers cool immediately when the microwave power is turned off. Therefore, ceramic layers are inserted between the SiC fiber layers to improve the heat conservation performance of SiC fiber mats. In this study, we fabricated SiC fiber mat composites (SMCs) with ceramic layers under various pressures. The SMC fabricated under 0.007 kPa showed the lowest heat-generating temperature and deviation because less necking was observed between the materials. On the other hand, the SMC fabricated under 0.375 kPa showed the highest heat-generating temperature of 1532.33℃. The SMCs prepared in this study using ceramic powder not only showed heat-generating temperatures comparable to those of conventional SiC fiber mats but also exhibited excellent heat-preserving ability.

• Journal of Welding and Joining
• /
• 제27권5호
• /
• pp.62-67
• /
• 2009

Welding deformation during the assembly process is affected by not only local shrinkage due to rapid heating and cooling, but also root gap and misalignment between parts to be welded. Therefore, the prediction and control of welding deformation have become of critical importance. In this study, it was focused on the development of the 3-axis apparatus for real-time measurement of the welded deformation. To achieve the objective, a D-H algorithm has been carried out to check the behavioral and performance evaluation for the developed robot. The sequence experiments were taken the base materials of $400{\times}200{\times}4.5mm$ plate for butt welding. The real-time experimental measurements are in good agreement with the measured results.

• 한국자동차공학회논문집
• /
• 제8권4호
• /
• pp.51-58
• /
• 2000

It is well known that the majority of the emissions measured from vehicle exhaust in the US Federal Test Procedure(FTP-75) are emitted during the first 60 seconds. This paper describes an experimental study on SI engine emissions reduction after cold start with interval secondary air injection and coolant control. Secondary air injection after cold start to reduce exhaust emissions causes an exothermic reaction at the exhaust port and gives sufficient air to the catalyst. For that reason engine-out emissions oxidized in the exhaust port and the rapid heating of a catalytic converter after cold start with CSAI and ISAI are estimated. The influence of the coolant temperature on SI engine emissions has been estimated. In the present studycoolant control of the cylinder head tempeature is used to investigate the effect of coolant temperature on SI engine emissions. The results show that engine-out hydrocarbon and carbon monoxide emissions are considerably reduced with interval secondary air injection and coolant control.