• Journal of Advanced Marine Engineering and Technology
• /
• v.15 no.1
• /
• pp.59-70
• /
• 1991

Rupture of lubricant film, thermal characteristics, and variation of viscosity are very important factors to evaluate the performance of journal bearing. Variation of external conditions, load or rotational speed, largely influence these facters. For example, if rotational speed increases lubricant bulk temperature increases and viscosity drops. In this paper the effect of rotational speed variation on the characteristics of lubricant film in a journal bearing is investigated by experiment and theoretical analysis. It has been measured number of lubricant film rupture and lubricant bulk temperature form journal bearing which have been established at the various operating speed of shaft. The range of speed variation is from 900rpm to 2100rpm. Theoretical analysis has been carried out for rupture of lubricant film and thermal characteristics, and these results are compared with experimental results.

• Journal of Korean Society for Atmospheric Environment
• /
• v.10 no.3
• /
• pp.203-208
• /
• 1994

The trend of visibility variation of Seoul during 1980-1993 is analyzed. Annual average visibility has been decreased during the 1980s except 1988 and 1989 but not decreasing during the early 1990s. Also, the number of days with haze during 1983-1993 did not increase. Mixing height is deemed to be a dominant factor determining visibility. During the period, the difference between the average visibility at 6 p.m and 9 a.m decreased with the average visual range at 9 a.m slightly increased. Thus there is possibility that the effect of Photochemcial reactions becomes noticeable. The number of vehicles and the concentration of criteria air pollutants on the trend of visibility variation of Seoul would not be directly related to the variation of visibility.

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.34C no.12
• /
• pp.37-42
• /
• 1997

A new temperature and supply-insensitive CMOS current reference circuit was designed and tested. Te temperature insensuitivity was achieved by eliminating the mobility dependence term through the multiplication of two current components, one which is proportional to mobility and the other which is inversely proportional to mobility, by using a newly designed CMOS square root circuit. The CMOS sqare root circuit was derived from its bipolar counterpart by operating the MOS transistors in the subthreshold region. The supply insensitivity was achieved by using an internal voltage generator. Te test chip was designed ans sent out for fabrication by using a 2.mu.m double-poly double-metal n-well CMOS technology. When an external voltage source was used for the square root circuit, the maximum variation and the average temperature sensitivity were measured to be 3% and 21.4ppm/.deg.C, respectively, for the temperature range of -15~130.deg.C. The maximum current variation with supply voltage was measured to be 3% within the commerical supply voltage range of 4.5~5.5V at 30.deg. C.

• Speech Sciences
• /
• v.8 no.3
• /
• pp.93-104
• /
• 2001

The author analyzed acoustic parameters of ten Korean numbers produced by ten male students using Praat. Variations of f0, F1, F2 and F3 within and between speakers were examined by determining an average and standard deviation of the parameters of each number and by comparing the acoustic values with one another. Results showed that each subject produced the numbers within a certain range of variation across time. Thus, speaker identification can be more certain using dynamic information of the acoustic parameters within each vocalic segment. Also, percent difference of within-subjects' variation to that of between-subjects can be utilized to determine which sounds would be better stimuli for speaker identification. According to the criteria, the number '2' proved the best stimulus while the number '7' was the worst. Future studies will be necessary to explore robust methods of speaker identification under noisy conditions.

• Journal of Sensor Science and Technology
• /
• v.13 no.2
• /
• pp.133-138
• /
• 2004

Today, the obstacle detection system has massive size and restrictive detection range. To solve these problems, this paper proposes the capacitance variation detector using the variated capacitance value as a result of the obstacle approaching. If obstacle approaches, the capacitance value of capacitance sensor is increased and the operating frequency of oscillator is decreased. Then this changed frequency appears to the output of the mixer that operate down conversion. The capacitance variation detector is produced by Hynix$0.35{\mu}$ CMOS process. In experiment result, the frequency of final output is 6.81 MHz at no obstacle and 31.45 MHz at approaching obstacle. In conclusion, proposed capacitance variation detector has small size, low power consumption and easiness to set up anywhere. So it is expected to substitute the obstacle detector.

• Journal of Institute of Control, Robotics and Systems
• /
• v.6 no.7
• /
• pp.611-616
• /
• 2000

This paper presents a design method for the robust flight controller of a hyghly maneuvering aircraft subject to C.G variation. This method is based on LMI(Linear Matrix ZInequality) pole-placement design methodology for the polytopic models. Simulation results show that the proposed LMI-based pole-placement design methodology robustly yields uniform performance with adequate Flying Qualities (FQ) over the entire CG variation range.

• Journal of Advanced Information Technology and Convergence
• /
• v.8 no.2
• /
• pp.59-67
• /
• 2018

The minimum power supply voltage of a typical bandgap current reference (BGCR) is limited by operating temperature and input common mode range (ICMR) of a feedback amplifier. A new BGCR using a bandgap voltage generator (BGVG) is proposed to minimize the effect of temperature, supply voltage, and process variation. The BGVG is designed with proportional to absolute temperature (PTAT) characteristic, and a feedback amplifier is designed with weak-inversion transistors for low voltage operation. It is verified with a $0.18-{\mu}m$ CMOS process with five corners for MOS transistors and three corners for BJTs. The proposed circuit is superior to other reported current references under temperature variation from $-40^{\circ}C$ to $120^{\circ}C$ and power supply variation from 1.2 V to 1.8 V. The total power consumption is $126{\mu}W$ under the conditions that the power supply voltage is 1.2 V, the output current is $10{\mu}A$, and the operating temperature is $20^{\circ}C$.

• Journal of the Korean Society for Geothermal and Hydrothermal Energy
• /
• v.13 no.2
• /
• pp.22-29
• /
• 2017

This study is performed to performance of the combined system the GSHP (Ground Source Heat Pump) system with the Earth tube system using EnergyPlus program. The Earth tube system using fan is characteristics as supply lower (higher) air temperature than outdoor air temperature in cooling and heating seasons, the GSHP system is characteristics as small indoor air temperature variation range. As the results of Earth tube + GSHP system simulation, GSHP power can be reduced than the GSHP single operation as 17.3% in cooling seasons and 32.5% in heating seasons, the GSHP design capacity can be replaced more small size.

• Proceedings of the Korean Operations and Management Science Society Conference
• /
• 2002.05a
• /
• pp.923-929
• /
• 2002

We discuss scheduling analysis for a discrete event system with time windows of which firing or holding time delays are subject to random variation within some finite range. To do this, we propose a modified p-lime Petri net, named p+-time Petri net. We develop a condition for which a synchronized transition does not have a dead token, that is, the firing epochs do not violate the time window constraints. We propose a method of computing the feasible range of the token sojourn time at each place based on a time difference graph. We also discuss an application for analyzing wafer residency times within the process chambers for a dual-armed cluster tool for chemical vapor deposition.

• Journal of Environmental Health Sciences
• /
• v.33 no.5
• /
• pp.451-455
• /
• 2007

This study was performed to evaluate the effects of input ratios of bulking material in aerobic composting of food wastes on variation of colony forming units(CFU) of fungi. Wood chips were used as a bulking material. Volume ratios of food wastes to wood chips in reactor of Control, WC-1 and WC-2 were 10/0, 10/5 and 10/10, respectively. Reactors were operated for 24 days with I hour stirring by 1rpm and 2 hours of the forced aeration rate of $80L/min{\cdot}m^3$ per day. WC-2 reached high temperature range faster than WC-1, and the maximum temperature of WC-2 was higher than that of WC-1. WC-2 reached high pH range faster than WC-1. and the maximum pH of WC-2 was higher than that of WC-1. WC-2 reached high Log(CFU/gram) range faster than WC-I, and the maximum Log(CFU/gram) of WC-2 was higher than that of WC-1. These all mean that the reaction velocity of composting of WC-2 was faster than that of WC-1. The profile of fungi changes in Log(CFU/gram) was similar to that of temperature changes (r=0.8861) not pH changes (r=0.1631).