• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2005년도 International Meeting on Information Displayvol.I
• /
• pp.307-309
• /
• 2005

We investigated light absorption layer effect on metal-induced lateral crystallization (MILC) growth rate and MILC thin films transistors (TFTs). As annealing method, we used scanning-rapid thermal annealing (RTA). MILC growth rate which was crystallized by light absorption layer and using scanning-RTA was 3 times than normal MILC which was without light absorption layer growth rate. Also we compared MILC TFTs characteristics which were combined to light absorption layer with conventional MILC TFTs. After scanning-RTA process, MILC-TFTs which were with light absorption layer were superior to conventional MILC-TFTs. With this new MILC-TFTs structure, we could reduced crystallization time and obtain good electrical properties.

• Journal of Magnetics
• /
• 제6권4호
• /
• pp.126-128
• /
• 2001

The effect of rapid thermal anneal (RTA) has been investigated on the properties of an FeMn exchange-biased magnetic tunnel junction (MTJ) using magnetoresistance and I-V measurements and transmission electron microscopy (TEM). The tunneling magnetoresistance (TMR) in an as-grown MTJ is found to be ∼27%, while the TMR in MTJs annealed by RTA increases with annealing temperature up to 300$\^{C}$, reaching ∼46%. A TEM image reveals a structural change in the interface of A1$_2$O$_3$layer for the MTJ annealed by RTA at 300$\^{C}$. The oxide barrier parameters are found to vary abruptly with annealing time within a few ten seconds. Our results demonstrate that the present RTA enhances the magnetoresistive properties of MTJs.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 제37회 하계학술대회 논문집 C
• /
• pp.1424-1425
• /
• 2006

A four-step rapid thermal annealing (RTA) process is proposed in order to improve the throughput and stabilize the process, compared to the six-step RTA process. Effects of annealing on the properties of a structure mode of CMOS process in both cases were investigated. The implanted dopant(As, $BF_2$ and Ti/TiN) movement in silicon during different rapid thermal annealing conditions was studied using secondary ion mass spectroscopy (SIMS) technique. These results show that the four-step RTA process significantly improves time effect and throughput (15%) by the condition of ramping up compared to the six-step RTA process.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1994년도 추계 학술발표 강연 및 논문 개요집
• /
• pp.53-54
• /
• 1994

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1992년도 춘계학술발표회
• /
• pp.96-97
• /
• 1992

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1996년도 재료학회 추계학술발표회
• /
• pp.49-49
• /
• 1996

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 1996년도 재료학회 추계학술발표회
• /
• pp.58-58
• /
• 1996

• The Korean Journal of Ceramics
• /
• 제6권2호
• /
• pp.138-142
• /
• 2000

Thin film $LiNbO_3$MFS (metal-ferroelectric-semiconductor) capacitor showed improved characteristics such as low interface trap density, low interaction with Si substrate, and large remanent polarization. This paper reports ferroelectric $LiNbO_3$thin films grown directly on p-type Si (100) substrates by 13.56 MHz RF magnetron sputtering system for FRAM (ferroelectric random access memory) applications. RTA (rapid thermal anneal) treatment was performed for as-deposited films in an oxygen atmosphere at $600^{\circ}C$ for 60sec. We learned from X-ray diffraction that the RTA treated films were changed from amorphous to poly-crystalline $LiNbO_3$which exhibited (012), (015), (022), and (023) plane. Low temperature film growth and post RTA treatments improved the leakage current of $LiNbO_3$films while keeping other properties almost as same as high substrate temperature grown samples. The leakage current density of $LiNbO_3$films decreased from $10^{-5}$ to $10^{-7}$A/$\textrm{cm}^2$ after RTA treatment. Breakdown electric field of the films exhibited higher than 500 kV/cm. C-V curves showed the clockwise hysteresis which represents ferroelectric switching characteristics. Calculated dielectric constant of thin film $LiNbO_3$illustrated as high as 27.9. From ferroelectric measurement, the remanent polarization and coercive field were achieved as 1.37 $\muC/\textrm{cm}^2$ and 170 kV/cm, respectively.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.414-414
• /
• 2013

InGaAlAs/InP은 $1.3{\sim}1.55{\mu}m$ 레이저 다이오드 응용을 위한 InGaAsP/InP를 대체하기 위한 물질로 많은 관심을 받아왔다. 디지털 합금 InGaAlAs 다중양자우물(multiple quantum wells: MQWs) 시료는 MBE (molecular beam epitaxy) 장비를 이용하여 n-InP 기판 위에 성장하였다. 양자우물과 장벽은 각각 (InGaAs)0.8(InAlAs)0.2와 (InGaAs)0.4(InAlAs)0.6 SPSs (short-period superlattices)로 $510^{\circ}C$에서 성장하였다. 발광특성을 향상시키기 위하여 질소분위기에서 $700^{\circ}C$ $750^{\circ}C$ 또는 $800^{\circ}C$에서 30초간 열처리(rapid thermal annealing: RTA)하였다. RTA 온도에 따른 디지털 합금 InGaAlAs MQWs의 발광특성을 분석하기 위해 PL (photoluminescence)과 TRPL(time-resolved PL)을 이용하였다. RTA 온도에 따른 InGaAlAs MQWs 시료의 발광 메카니즘 및 운반자 동력학을 연구하기 위하여 발광파장 및 온도에 따른 TRPL을 측정하였다. 저온(10 K)에서 PL 피크는 RTA 온도를 $700^{\circ}C$에서 $750^{\circ}C$로 증가하였을 때 1,242 nm에서 1,245 nm로 장파장 영역으로 이동하였다가 $800^{\circ}C$에서 열처리하였을 때 단파장 영역으로 이동하여 1,239 nm에서 나타났다. 또한 PL 세기는 RTA 온도를 증가함에 따라 증가함을 보이다가 RTA 온도를 $800^{\circ}C$로 증가하였을 때 PL 세기는 감소하였다. 발광소자 개발을 위한 InAlGaAs MQWs 시료의 최적의 열처리 조건을 이러한 PL과 TRPL 결과로부터 결정할 수 있다.

• 전자공학회논문지A
• /
• 제31A권8호
• /
• pp.80-90
• /
• 1994

The ultra shallow junction was formed by 2-step RTP. Phosphorus solid source(P$_{2}O_{5}$) was transfered on wafer surface during RTG(Rapid Thermal Glass Transfer) of which process condition was 80$0^{\circ}C$ and 60sec. The process temperature and time of the RTD(Rapid Thermal Diffusion) were 950~105$0^{\circ}C$ during 5~15sec respectively sheet resistances were measured as 175~320$\Omega$/m and junction depth and dopth and dopant surface concentration were measured as 0.075~0.18$\mu$m and 5${\times}10^{19}cm^{4}$ respectively. Ti-silicide was formed by 2-step RTA after 300$\AA$ Titanium was deposited. The 1st RTA (2nd RTA) was carried out at the temperature of $600^{\circ}C$(700~80$0^{\circ}C$) for 30 seconds (10~60 seconds) under N$_2$ ambient. Sheet resistances after 2nd RTA were measured as 46~63$\Omega$/D. Si/Ti component ratio was evaulated as 1.6~1.9 from Auger depth profile. Ti-Silicided n-p junction diode (pattern size : 400$\times$400$\mu$m) was fabricated under the RTD(the process was carried out at the temperature of 100$0^{\circ}C$ for 10seconds) and 2nd RTA(theprocess was carried out at the temperature of 750$^{\circ}C$ for 60 seconds). Leakage current was measured 1.8${\times}10^{7}A/mm^{2}$ at 5V reverse voltage. Whent the RTD process condition is at the temperature of 100$0^{\circ}C$ for 10seconds and the 2nd RTA process condition is at the temperature of 75$0^{\circ}C$ for 60 seconds leakage current was 29.15${\times}10^{9}A$(at 5V).